Author Topic: Help with secondary-feedback?  (Read 2521 times)

Offline nabzim

  • High Voltage Enthusiast
  • *
  • Posts: 25
  • Karma: +0/-0
  • My full name is Adam Baltazar Mizban. Hello there!
    • View Profile
    • My YouTube Channel
Help with secondary-feedback?
« on: June 27, 2017, 08:03:57 PM »
I made a post last night about my SSTC, but I realized I may as well ask for help with this issue I had. I have been only successful with with antenna feedback, and while it works great, it would be nice to not need a giant antenna sticking up and out of the base, always needing to be re-bent into a good position if it gets shifted while moving around and whatnot.
I attempted to use this current transformer that I wound: https://goo.gl/photos/3Z2faavbYM8r9SvL9
It has 54 turns of 24awg and the core is this one: http://www.ebay.com/itm/Toroid-Core-Magnetics-ZW-42507-TC-Power-Ferrite-1-00-OD-2-PCS-AL-7825/261788162368?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649

So, basically it works but only at low voltage. When I turn it up, it cuts-out past a certain point on my variac. I had been trying to use loneocean's sstc2 as the reference point to set up secondary feedback, so my feedback circuit is set up like his (except I do not have .1nF cap between the UCC input and ground). http://www.loneoceans.com/labs/sstc2/sstc2schematicv10.jpg
 I also tried a 1k burden resistor across the transformer's leads, after reading about current transformers, although that seems to be used for measuring current with a multimeter.

So I'm looking for some idea as to what I may be doing wrong or what I should try next... maybe different burden resistors, more turns of wire, or that the .1nF cap is more important than I assumed?

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1113
  • Karma: +17/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Help with secondary-feedback?
« Reply #1 on: June 28, 2017, 10:30:55 AM »
Leaving the filter capacitor out from the output of the hex Schmidt inverters could be a potential problem, that induced noise at higher powers is enough to knock the circuit out of order.

A current transformer should have a burden resistor, else you do not have a voltage across its output, just a current across the diode, which then maybe works from a voltage drop point of view and can activate the input of the IC, but that should really be made correct with a resistor in my opinion.

Secondary base current is possibly around 50 mA and up to max 1 A, I am really guessing a little bit here, not completely sure how much it is in a small coil, so you have to design the CT and burden resistor to provide enough feedback for the inverter input to switch properly.

It could also be that you saturate the CT core, is there a difference between continues wave mode, audio interruption or normal interruption from what voltage level it stops working?
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline nabzim

  • High Voltage Enthusiast
  • *
  • Posts: 25
  • Karma: +0/-0
  • My full name is Adam Baltazar Mizban. Hello there!
    • View Profile
    • My YouTube Channel
Re: Help with secondary-feedback?
« Reply #2 on: June 28, 2017, 09:53:38 PM »
Leaving the filter capacitor out from the output of the hex Schmidt inverters could be a potential problem, that induced noise at higher powers is enough to knock the circuit out of order.

A current transformer should have a burden resistor, else you do not have a voltage across its output, just a current across the diode, which then maybe works from a voltage drop point of view and can activate the input of the IC, but that should really be made correct with a resistor in my opinion.

Secondary base current is possibly around 50 mA and up to max 1 A, I am really guessing a little bit here, not completely sure how much it is in a small coil, so you have to design the CT and burden resistor to provide enough feedback for the inverter input to switch properly.

It could also be that you saturate the CT core, is there a difference between continues wave mode, audio interruption or normal interruption from what voltage level it stops working?
So, I tried the .1nF filter cap and that worked, pretty much. I can still get it to cut-out like it did before by adjusting to the position of the primary on the secondary. It works flawlessly when the primary is less coupled and starts to cut out with higher coupling. I am assuming then that too much current flowing through the secondary is causing the "cutting-out" to happen somehow.
Also there is this effect (at the proper coupling) where the output is very similar to a "ramped" type of tesla coil, with single, non-branched sparks that are much quieter than normal ones. I took a video of it you can see here: https://goo.gl/photos/ayWtdxZWsgqYksEi6

Also, I tried the resistor again after the filter cap worked, but there was no significant change that I noticed, other than when turning up the variac, I wouldn't get any spark until 25v, but before I would start to see spark output somewhere between 5 to 10 volts.
« Last Edit: June 28, 2017, 09:56:35 PM by nabzim »

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1113
  • Karma: +17/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Help with secondary-feedback?
« Reply #3 on: July 01, 2017, 08:22:12 AM »
If they sparks get quiet like that, it means that you have a much lower peak current in the primary and the waveform is close to a non-distorted sinus wave, so the energy transfer to the secondary circuit is properly better.

Higher and higher input voltages to achieve break out is mostly a phenomenon that I know from the DRSSTCs, because we de-tune the primary circuit to account for the secondary spark loading de-tuning, so in extreme examples we do not get any output before some hundred volts on the DC bus. It could be that for your SSTC you do not have enough gain in the feedback loop for it to work at low voltage.
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

High Voltage Forum

Re: Help with secondary-feedback?
« Reply #3 on: July 01, 2017, 08:22:12 AM »

 


* Recent Topics and Posts

post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
Today at 05:54:23 AM
post Re: Blast from the past!
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
klugesmith
Today at 05:05:55 AM
post Re: UD2.7 Gate Signals
[Dual Resonant Solid State Tesla coils]
coilinator
September 17, 2019, 08:24:59 PM
post Re: Blast from the past!
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
MRMILSTAR
September 17, 2019, 08:19:45 PM
post Re: Blast from the past!
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Mads Barnkob
September 17, 2019, 06:53:52 PM
post Blast from the past!
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
MRMILSTAR
September 17, 2019, 05:52:00 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
September 17, 2019, 05:00:47 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
davekni
September 17, 2019, 06:48:38 AM
post Re: My second DRSSTC
[Dual Resonant Solid State Tesla coils]
erdal
September 16, 2019, 11:07:27 PM
post Re: 750W solar offgrid 24V/150Ah battery setup with Victron charger
[Electronic circuits]
johnf
September 16, 2019, 09:48:37 PM
post Re: adventures in homemade flyback bobbins.
[Transformer (ferrite core)]
AlexanderHun
September 16, 2019, 10:42:44 AM
post Re: Offgrid 48V solar to 24V battery setup
[Electronic circuits]
Mads Barnkob
September 16, 2019, 09:40:27 AM
post Re: My second DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
September 16, 2019, 09:28:43 AM
post Re: Large Ferrite Core with IGBT-Brick Driver
[Transformer (ferrite core)]
Mads Barnkob
September 16, 2019, 09:24:17 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
T3sl4co1l
September 16, 2019, 06:59:12 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
davekni
September 16, 2019, 04:18:26 AM
post Re: My second DRSSTC
[Dual Resonant Solid State Tesla coils]
davekni
September 16, 2019, 02:49:28 AM
post Re: Large Ferrite Core with IGBT-Brick Driver
[Transformer (ferrite core)]
davekni
September 16, 2019, 02:43:18 AM
post Re: Homemade HV transformer
[Transformer (ferrite core)]
davekni
September 16, 2019, 02:36:17 AM
post Re: adventures in homemade flyback bobbins.
[Transformer (ferrite core)]
davekni
September 16, 2019, 02:26:40 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
September 16, 2019, 01:50:19 AM
post Re: UD2.7 Gate Signals
[Dual Resonant Solid State Tesla coils]
coilinator
September 15, 2019, 08:22:47 PM
post Re: My second DRSSTC
[Dual Resonant Solid State Tesla coils]
erdal
September 15, 2019, 02:09:17 PM
post Re: Homemade HV transformer
[Transformer (ferrite core)]
AlexanderHun
September 15, 2019, 10:39:29 AM
post Re: Homemade HV transformer
[Transformer (ferrite core)]
ElectroXa
September 14, 2019, 07:01:28 PM
post Re: adventures in homemade flyback bobbins.
[Transformer (ferrite core)]
AlexanderHun
September 14, 2019, 06:59:13 PM
post Re: Homemade HV transformer
[Transformer (ferrite core)]
AlexanderHun
September 14, 2019, 06:43:15 PM
post Re: Homemade HV transformer
[Transformer (ferrite core)]
ritaismyconscience
September 14, 2019, 06:35:32 PM
post Homemade HV transformer
[Transformer (ferrite core)]
AlexanderHun
September 14, 2019, 05:05:00 PM
post Re: UD2.7 Gate Signals
[Dual Resonant Solid State Tesla coils]
profdc9
September 14, 2019, 04:50:10 PM
post Re: UD2.7 Gate Signals
[Dual Resonant Solid State Tesla coils]
coilinator
September 14, 2019, 08:42:55 AM
post Re: Transistors good for DRSSTC?
[Dual Resonant Solid State Tesla coils]
ritaismyconscience
September 13, 2019, 05:50:53 AM
post Re: Transistors good for DRSSTC?
[Dual Resonant Solid State Tesla coils]
Max
September 12, 2019, 12:47:03 PM
post Re: Transistors good for DRSSTC?
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
September 12, 2019, 11:07:39 AM
post Re: "karma", "applause/smite" button meaning and use
[General chatting]
Mads Barnkob
September 12, 2019, 11:01:05 AM
post Re: Transistors good for DRSSTC?
[Dual Resonant Solid State Tesla coils]
Hydron
September 12, 2019, 08:44:48 AM
post Transistors good for DRSSTC?
[Dual Resonant Solid State Tesla coils]
ritaismyconscience
September 12, 2019, 05:53:51 AM
post Re: "karma", "applause/smite" button meaning and use
[General chatting]
oneKone
September 12, 2019, 05:37:11 AM
post "karma", "applause/smite" button meaning and use
[General chatting]
MRMILSTAR
September 12, 2019, 05:07:24 AM
post Re: Why did 4HV die??
[General chatting]
oneKone
September 12, 2019, 04:50:24 AM
post Drsstc 4, I'm never stopping
[Dual Resonant Solid State Tesla coils]
oneKone
September 12, 2019, 02:36:00 AM
post Re: Why did 4HV die??
[General chatting]
Hydron
September 12, 2019, 12:34:10 AM
post Re: Why did 4HV die??
[General chatting]
MRMILSTAR
September 11, 2019, 09:29:40 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
MRMILSTAR
September 11, 2019, 09:00:31 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
coilinator
September 11, 2019, 07:54:30 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
freq_out
September 11, 2019, 05:40:14 PM
post Re: SSTC not getting interrupted
[Solid state Tesla coils]
Fumeaux
September 11, 2019, 02:38:40 PM
post Re: SSTC not getting interrupted
[Solid state Tesla coils]
Saattvik24
September 11, 2019, 01:54:59 PM
post Re: Induction Heater schematic modification
[Electronic circuits]
ritaismyconscience
September 11, 2019, 07:48:43 AM
post Re: Using static electricity in the car painting
[Static electricity]
johnf
September 11, 2019, 07:00:03 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30