Author Topic: Help with secondary-feedback?  (Read 3177 times)

Offline nabzim

  • High Voltage Enthusiast
  • *
  • Posts: 25
  • Karma: +0/-0
  • My full name is Adam Baltazar Mizban. Hello there!
    • View Profile
    • My YouTube Channel
Help with secondary-feedback?
« on: June 27, 2017, 08:03:57 PM »
I made a post last night about my SSTC, but I realized I may as well ask for help with this issue I had. I have been only successful with with antenna feedback, and while it works great, it would be nice to not need a giant antenna sticking up and out of the base, always needing to be re-bent into a good position if it gets shifted while moving around and whatnot.
I attempted to use this current transformer that I wound: https://goo.gl/photos/3Z2faavbYM8r9SvL9
It has 54 turns of 24awg and the core is this one: http://www.ebay.com/itm/Toroid-Core-Magnetics-ZW-42507-TC-Power-Ferrite-1-00-OD-2-PCS-AL-7825/261788162368?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649

So, basically it works but only at low voltage. When I turn it up, it cuts-out past a certain point on my variac. I had been trying to use loneocean's sstc2 as the reference point to set up secondary feedback, so my feedback circuit is set up like his (except I do not have .1nF cap between the UCC input and ground). http://www.loneoceans.com/labs/sstc2/sstc2schematicv10.jpg
 I also tried a 1k burden resistor across the transformer's leads, after reading about current transformers, although that seems to be used for measuring current with a multimeter.

So I'm looking for some idea as to what I may be doing wrong or what I should try next... maybe different burden resistors, more turns of wire, or that the .1nF cap is more important than I assumed?

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1331
  • Karma: +21/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Help with secondary-feedback?
« Reply #1 on: June 28, 2017, 10:30:55 AM »
Leaving the filter capacitor out from the output of the hex Schmidt inverters could be a potential problem, that induced noise at higher powers is enough to knock the circuit out of order.

A current transformer should have a burden resistor, else you do not have a voltage across its output, just a current across the diode, which then maybe works from a voltage drop point of view and can activate the input of the IC, but that should really be made correct with a resistor in my opinion.

Secondary base current is possibly around 50 mA and up to max 1 A, I am really guessing a little bit here, not completely sure how much it is in a small coil, so you have to design the CT and burden resistor to provide enough feedback for the inverter input to switch properly.

It could also be that you saturate the CT core, is there a difference between continues wave mode, audio interruption or normal interruption from what voltage level it stops working?
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline nabzim

  • High Voltage Enthusiast
  • *
  • Posts: 25
  • Karma: +0/-0
  • My full name is Adam Baltazar Mizban. Hello there!
    • View Profile
    • My YouTube Channel
Re: Help with secondary-feedback?
« Reply #2 on: June 28, 2017, 09:53:38 PM »
Leaving the filter capacitor out from the output of the hex Schmidt inverters could be a potential problem, that induced noise at higher powers is enough to knock the circuit out of order.

A current transformer should have a burden resistor, else you do not have a voltage across its output, just a current across the diode, which then maybe works from a voltage drop point of view and can activate the input of the IC, but that should really be made correct with a resistor in my opinion.

Secondary base current is possibly around 50 mA and up to max 1 A, I am really guessing a little bit here, not completely sure how much it is in a small coil, so you have to design the CT and burden resistor to provide enough feedback for the inverter input to switch properly.

It could also be that you saturate the CT core, is there a difference between continues wave mode, audio interruption or normal interruption from what voltage level it stops working?
So, I tried the .1nF filter cap and that worked, pretty much. I can still get it to cut-out like it did before by adjusting to the position of the primary on the secondary. It works flawlessly when the primary is less coupled and starts to cut out with higher coupling. I am assuming then that too much current flowing through the secondary is causing the "cutting-out" to happen somehow.
Also there is this effect (at the proper coupling) where the output is very similar to a "ramped" type of tesla coil, with single, non-branched sparks that are much quieter than normal ones. I took a video of it you can see here: https://goo.gl/photos/ayWtdxZWsgqYksEi6

Also, I tried the resistor again after the filter cap worked, but there was no significant change that I noticed, other than when turning up the variac, I wouldn't get any spark until 25v, but before I would start to see spark output somewhere between 5 to 10 volts.
« Last Edit: June 28, 2017, 09:56:35 PM by nabzim »

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1331
  • Karma: +21/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Help with secondary-feedback?
« Reply #3 on: July 01, 2017, 08:22:12 AM »
If they sparks get quiet like that, it means that you have a much lower peak current in the primary and the waveform is close to a non-distorted sinus wave, so the energy transfer to the secondary circuit is properly better.

Higher and higher input voltages to achieve break out is mostly a phenomenon that I know from the DRSSTCs, because we de-tune the primary circuit to account for the secondary spark loading de-tuning, so in extreme examples we do not get any output before some hundred volts on the DC bus. It could be that for your SSTC you do not have enough gain in the feedback loop for it to work at low voltage.
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

High Voltage Forum

Re: Help with secondary-feedback?
« Reply #3 on: July 01, 2017, 08:22:12 AM »

 


* Recent Topics and Posts

post Re: Class E SSTC Topology
[Solid State Tesla Coils (SSTC)]
davekni
Today at 06:38:45 AM
post Re: Power MOSFETs with fast recovery body diodes
[Electronic Circuits]
John123
Today at 06:33:52 AM
post Re: Power MOSFETs with fast recovery body diodes
[Electronic Circuits]
davekni
Today at 05:47:51 AM
post Re: Power MOSFETs with fast recovery body diodes
[Electronic Circuits]
John123
Today at 05:32:41 AM
post Re: Power MOSFETs with fast recovery body diodes
[Electronic Circuits]
T3sl4co1l
Today at 05:10:31 AM
post Re: Class E SSTC Topology
[Solid State Tesla Coils (SSTC)]
ZakW
Today at 04:17:27 AM
post Re: Power MOSFETs with fast recovery body diodes
[Electronic Circuits]
John123
April 08, 2020, 11:40:04 PM
post Has anybody got this board?
[Solid State Tesla Coils (SSTC)]
TMS
April 08, 2020, 10:34:42 PM
post Re: TVS diode selection for 400v transistor
[Electronic Circuits]
John123
April 08, 2020, 07:53:19 PM
post Re: GDT keeps on killing IGBTs
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
April 08, 2020, 04:15:12 AM
post Re: GDT keeps on killing IGBTs
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ritaismyconscience
April 08, 2020, 01:05:28 AM
post Re: TVS diode selection for 400v transistor
[Electronic Circuits]
SteveN87
April 08, 2020, 12:53:15 AM
post Re: GDT keeps on killing IGBTs
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
April 07, 2020, 10:54:57 PM
post Re: GDT keeps on killing IGBTs
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ritaismyconscience
April 07, 2020, 10:24:16 PM
post Re: Class E SSTC Topology
[Solid State Tesla Coils (SSTC)]
ZakW
April 07, 2020, 09:22:16 PM
post Re: Class E SSTC Topology
[Solid State Tesla Coils (SSTC)]
johnf
April 07, 2020, 09:04:34 PM
post Re: Class E SSTC Topology
[Solid State Tesla Coils (SSTC)]
ZakW
April 07, 2020, 08:48:01 PM
post Re: Class E SSTC Topology
[Solid State Tesla Coils (SSTC)]
Weston
April 07, 2020, 08:15:43 PM
post Re: TVS diode selection for 400v transistor
[Electronic Circuits]
John123
April 07, 2020, 06:23:47 PM
post Re: Where is plasma globe arc arcing to?
[Beginners]
John123
April 07, 2020, 05:59:09 PM
post Re: Where is plasma globe arc arcing to?
[Beginners]
alan sailer
April 07, 2020, 04:30:26 PM
post Re: Powerful easy to build MIDI Interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Max
April 07, 2020, 01:10:30 PM
post Re: TVS diode selection for 400v transistor
[Electronic Circuits]
SteveN87
April 07, 2020, 12:44:56 PM
post Re: Where is plasma globe arc arcing to?
[Beginners]
John123
April 07, 2020, 07:05:30 AM
post Re: Where is plasma globe arc arcing to?
[Beginners]
Jun
April 07, 2020, 06:40:02 AM
post Re: Class E SSTC Topology
[Solid State Tesla Coils (SSTC)]
ZakW
April 07, 2020, 05:07:31 AM
post Re: TVS diode selection for 400v transistor
[Electronic Circuits]
John123
April 07, 2020, 03:38:12 AM
post Re: TVS diode selection for 400v transistor
[Electronic Circuits]
SteveN87
April 07, 2020, 03:21:55 AM
post Re: TVS diode selection for 400v transistor
[Electronic Circuits]
John123
April 07, 2020, 02:59:28 AM
post Re: TVS diode selection for 400v transistor
[Electronic Circuits]
davekni
April 07, 2020, 02:52:19 AM
post Re: Small DIY plasma globe using ZVS oscillator
[Transformer (Ferrite Core)]
John123
April 07, 2020, 02:29:21 AM
post Re: Where is plasma globe arc arcing to?
[Beginners]
John123
April 07, 2020, 02:21:55 AM
post Re: TVS diode selection for 400v transistor
[Electronic Circuits]
John123
April 07, 2020, 02:00:26 AM
post Re: TVS diode selection for 400v transistor
[Electronic Circuits]
SteveN87
April 07, 2020, 01:25:47 AM
post Re: TVS diode selection for 400v transistor
[Electronic Circuits]
John123
April 07, 2020, 12:38:59 AM
post Re: TVS diode selection for 400v transistor
[Electronic Circuits]
petespaco
April 07, 2020, 12:13:11 AM
post Re: Corona lockdown thread, tell about your situation
[General Chat]
John123
April 06, 2020, 10:07:59 PM
post Re: TVS diode selection for 400v transistor
[Electronic Circuits]
davekni
April 06, 2020, 10:07:11 PM
post Re: Corona lockdown thread, tell about your situation
[General Chat]
Mads Barnkob
April 06, 2020, 09:57:29 PM
post Re: TVS diode selection for 400v transistor
[Electronic Circuits]
John123
April 06, 2020, 08:04:52 PM
post Re: Power MOSFETs with fast recovery body diodes
[Electronic Circuits]
John123
April 06, 2020, 07:49:30 PM
post Re: Where is plasma globe arc arcing to?
[Beginners]
davekni
April 06, 2020, 06:30:24 PM
post Re: GDT keeps on killing IGBTs
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
April 06, 2020, 06:23:27 PM
post Where is plasma globe arc arcing to?
[Beginners]
Jun
April 06, 2020, 02:10:18 PM
post Re: Interuppter code help for sstc (LONEOCEANS SSTC2 )
[Solid State Tesla Coils (SSTC)]
Max
April 06, 2020, 10:21:47 AM
post Journey to a small stand alone CW signal synthesizer
[Radio Frequency]
Da_Stier
April 06, 2020, 09:56:07 AM
post Re: GDT keeps on killing IGBTs
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ritaismyconscience
April 06, 2020, 05:09:29 AM
post Re: Class E SSTC Topology
[Solid State Tesla Coils (SSTC)]
ZakW
April 06, 2020, 02:26:28 AM
post Re: Skm100 coil
[Dual Resonant Solid State Tesla coils (DRSSTC)]
oneKone
April 06, 2020, 02:16:56 AM
post Re: Portable Q(uarantine)CW Tesla Coil
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
April 06, 2020, 12:43:50 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal