Author Topic: Corona on the.... GDT??  (Read 115 times)

Offline nick

  • High Voltage Enthusiast
  • *
  • Posts: 9
  • Karma: +0/-0
    • View Profile
Corona on the.... GDT??
« on: November 29, 2019, 12:40:05 PM »
Weird experience I had yesterday. I built a GDT for a full bridge but was testing it on my half bridge. The coil worked as expected (albeit I mostly test at voltages ~45v) but I spent probably 15 minutes trying to figure out where the sound of a second spark breakout was taking place (in addition to the breakout point). I was then surprised to notice that the sound was coming from the GDT (with 2 coils left open) and even more surprised to see a light corona between the wires... it was weird but kind of pretty.

Anyway when I connect it to the full bridge, this effect disappears (unfortunately the coil itself doesn't work but that's another story....).

I'm guessing the disconnected windings are acting like antennas? Interesting that it doesn't seem to negatively affect the performance of the half bridge....

Offline Weston

  • High Voltage Enthusiast
  • *
  • Posts: 27
  • Karma: +2/-0
    • View Profile
Re: Corona on the.... GDT??
« Reply #1 on: December 01, 2019, 12:14:57 PM »
Is your driver circuit grounded? Are you using antenna feedback? The secondary wires are close to the primary windings so the electric field for the two should be ~ the same, so unless things are really wired weird I don't think the unconnected windings are acting like an antenna. If you wanted to eliminate this as a cause you could connect one side of the unconnected GDT winding to a connected winding.

The secondary side of the GDT is referenced to the inverter, which has low impedance paths to defined voltages. Any voltage is likely between the primary and secondary, which means your driver circuit could be floating referenced to the inverter. Are you using a separate power supply for the driver? Is there a common ground or something?

High Voltage Forum

Re: Corona on the.... GDT??
« Reply #1 on: December 01, 2019, 12:14:57 PM »

 


* Recent Topics and Posts

post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
Today at 12:53:57 AM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
davekni
December 08, 2019, 09:57:51 PM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
MRMILSTAR
December 08, 2019, 05:28:09 PM
post Aethra CCD Webcam Teardown - From Back When Streaming Was Expensive!
[Electronic circuits]
Mads Barnkob
December 08, 2019, 01:33:30 PM
post Platter resistance & inductance
[Induction launchers, coil guns and rails guns]
klugesmith
December 08, 2019, 11:41:00 AM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
davekni
December 08, 2019, 06:50:11 AM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
plasma
December 08, 2019, 12:00:00 AM
post CW multiplier resistor string suggestions
[Voltage Multipliers]
MRMILSTAR
December 07, 2019, 11:32:49 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 07, 2019, 09:54:31 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 07, 2019, 09:48:21 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 07, 2019, 08:59:57 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
MRMILSTAR
December 06, 2019, 08:35:29 PM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 06, 2019, 05:19:26 AM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
davekni
December 06, 2019, 03:48:34 AM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
the_anomaly
December 06, 2019, 03:35:39 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
AstRii
December 06, 2019, 01:27:03 AM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 05, 2019, 11:38:59 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
Mads Barnkob
December 05, 2019, 07:33:01 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
sjsimmo
December 05, 2019, 11:09:20 AM
post Cost reduction in consumer electrics
[Electronic circuits]
klugesmith
December 05, 2019, 07:25:20 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 05, 2019, 05:52:11 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 05, 2019, 05:21:07 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 04, 2019, 06:05:11 PM
post Re: Full bridge showing half the voltage
[Beginners]
shrad
December 04, 2019, 02:57:02 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
Uspring
December 04, 2019, 12:40:51 PM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 04, 2019, 11:20:25 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 04, 2019, 08:28:15 AM
post Re: Full bridge showing half the voltage
[Beginners]
klugesmith
December 04, 2019, 07:41:21 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
MRMILSTAR
December 04, 2019, 05:15:49 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 04, 2019, 05:06:39 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 04, 2019, 04:31:16 AM
post Re: Full bridge showing half the voltage
[Beginners]
davekni
December 04, 2019, 04:26:38 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 04, 2019, 04:10:16 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 04, 2019, 12:28:15 AM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 04, 2019, 12:11:32 AM
post Re: HV resistor in oil
[Voltage Multipliers]
johnf
December 03, 2019, 07:58:41 PM
post Re: Driving Nixie-tubes with arduino
[Electronic circuits]
johnf
December 03, 2019, 07:54:08 PM
post Re: Full bridge showing half the voltage
[Beginners]
klugesmith
December 03, 2019, 07:41:00 PM
post Re: Driving Nixie-tubes with arduino
[Electronic circuits]
kamelryttarn
December 03, 2019, 02:14:00 PM
post Re: Driving Nixie-tubes with arduino
[Electronic circuits]
Mads Barnkob
December 03, 2019, 01:24:00 PM
post Re: Driving Nixie-tubes with arduino
[Electronic circuits]
klugesmith
December 03, 2019, 10:45:58 AM
post Driving Nixie-tubes with arduino
[Electronic circuits]
kamelryttarn
December 03, 2019, 09:04:42 AM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 03, 2019, 07:29:48 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 03, 2019, 05:07:28 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 03, 2019, 04:34:46 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 02, 2019, 09:06:07 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
T3sl4co1l
December 02, 2019, 10:51:33 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 02, 2019, 05:49:05 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
December 02, 2019, 04:10:14 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
December 02, 2019, 04:09:37 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30