Author Topic: safty gap resisitor  (Read 137 times)

Offline thedoc298

  • High Voltage Experimenter
  • **
  • Posts: 65
  • Karma: +0/-0
    • View Profile
safty gap resisitor
« on: October 10, 2019, 06:54:46 PM »
I was reading back a few months and someone mentioned,"don't forget your safty gap resisitor, few ohms would be good". This would be so your cap is not doing a direct short which make sence. I am going to use a 100watt 4 ohm. The question is are you guys out their doing this and what value are you using. Thanks

Offline MRMILSTAR

  • High Voltage Technician
  • ***
  • Posts: 116
  • Karma: +4/-0
  • Cedar Rapids, Iowa
    • View Profile
Re: safty gap resisitor
« Reply #1 on: October 10, 2019, 08:38:04 PM »
The purpose of the safety gap is to protect the transformer, not the capacitor. If the capacitor is suitably rated in voltage (at least 2.5x) that should be protection enough for it.

Since the safety gap is there to protect the transformer, the safety gap should be connected in parallel with the normal spark gap. Because of this there is no need for a resistor because the discharge is still into the tesla primary coil which will oscillate with the capacitor as with the normal firing.

I have seen a circuit with the safety gap in series with a resistor connected across the capacitor but this makes no sense to me unless it is an attempt to protect an under-rated capacitor.

My safety gap is connected in parallel with my SRSG as with all other RSGTCs I have seen.
« Last Edit: October 10, 2019, 09:28:51 PM by MRMILSTAR »
Steve White
Cedar Rapids, Iowa
Retired electrical engineer

Offline thedoc298

  • High Voltage Experimenter
  • **
  • Posts: 65
  • Karma: +0/-0
    • View Profile
Re: safty gap resisitor
« Reply #2 on: October 11, 2019, 01:09:18 AM »
The purpose of the safety gap is to protect the transformer, not the capacitor. If the capacitor is suitably rated in voltage (at least 2.5x) that should be protection enough for it.

Since the safety gap is there to protect the transformer, the safety gap should be connected in parallel with the normal spark gap. Because of this there is no need for a resistor because the discharge is still into the tesla primary coil which will oscillate with the capacitor as with the normal firing.

I have seen a circuit with the safety gap in series with a resistor connected across the capacitor but this makes no sense to me unless it is an attempt to protect an under-rated capacitor.

My safety gap is connected in parallel with my SRSG as with all other RSGTCs I have seen.
[/quote

yea I just looked again and when the safty fires it is not dead shorting the cap which is what I thought. The primary is in series with it with the cap so no short.

When I looked at my papers I kept seeing the safty across the cap dead shorting when it would fire, but it was across the main spark gap. Anyway all is well and you fixed a problem that did not exist. Cant believe how my eyes were playing tricks. The whole problem is i drew the cap and the safty gap the same.

She is about ready to fire, just got to put the terry filter stuff in, kind of forgot that stuff, so a little backtracking. Thanks again I feel better now.

High Voltage Forum

Re: safty gap resisitor
« Reply #2 on: October 11, 2019, 01:09:18 AM »

 


* Recent Topics and Posts

post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
davekni
Today at 09:57:51 PM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
MRMILSTAR
Today at 05:28:09 PM
post Aethra CCD Webcam Teardown - From Back When Streaming Was Expensive!
[Electronic circuits]
Mads Barnkob
Today at 01:33:30 PM
post Platter resistance & inductance
[Induction launchers, coil guns and rails guns]
klugesmith
Today at 11:41:00 AM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
davekni
Today at 06:50:11 AM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
plasma
Today at 12:00:00 AM
post CW multiplier resistor string suggestions
[Voltage Multipliers]
MRMILSTAR
December 07, 2019, 11:32:49 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 07, 2019, 09:54:31 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 07, 2019, 09:48:21 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 07, 2019, 08:59:57 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
MRMILSTAR
December 06, 2019, 08:35:29 PM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 06, 2019, 05:19:26 AM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
davekni
December 06, 2019, 03:48:34 AM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
the_anomaly
December 06, 2019, 03:35:39 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
AstRii
December 06, 2019, 01:27:03 AM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 05, 2019, 11:38:59 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
Mads Barnkob
December 05, 2019, 07:33:01 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
sjsimmo
December 05, 2019, 11:09:20 AM
post Cost reduction in consumer electrics
[Electronic circuits]
klugesmith
December 05, 2019, 07:25:20 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 05, 2019, 05:52:11 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 05, 2019, 05:21:07 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 04, 2019, 06:05:11 PM
post Re: Full bridge showing half the voltage
[Beginners]
shrad
December 04, 2019, 02:57:02 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
Uspring
December 04, 2019, 12:40:51 PM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 04, 2019, 11:20:25 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 04, 2019, 08:28:15 AM
post Re: Full bridge showing half the voltage
[Beginners]
klugesmith
December 04, 2019, 07:41:21 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
MRMILSTAR
December 04, 2019, 05:15:49 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 04, 2019, 05:06:39 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 04, 2019, 04:31:16 AM
post Re: Full bridge showing half the voltage
[Beginners]
davekni
December 04, 2019, 04:26:38 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 04, 2019, 04:10:16 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 04, 2019, 12:28:15 AM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 04, 2019, 12:11:32 AM
post Re: HV resistor in oil
[Voltage Multipliers]
johnf
December 03, 2019, 07:58:41 PM
post Re: Driving Nixie-tubes with arduino
[Electronic circuits]
johnf
December 03, 2019, 07:54:08 PM
post Re: Full bridge showing half the voltage
[Beginners]
klugesmith
December 03, 2019, 07:41:00 PM
post Re: Driving Nixie-tubes with arduino
[Electronic circuits]
kamelryttarn
December 03, 2019, 02:14:00 PM
post Re: Driving Nixie-tubes with arduino
[Electronic circuits]
Mads Barnkob
December 03, 2019, 01:24:00 PM
post Re: Driving Nixie-tubes with arduino
[Electronic circuits]
klugesmith
December 03, 2019, 10:45:58 AM
post Driving Nixie-tubes with arduino
[Electronic circuits]
kamelryttarn
December 03, 2019, 09:04:42 AM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 03, 2019, 07:29:48 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 03, 2019, 05:07:28 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 03, 2019, 04:34:46 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 02, 2019, 09:06:07 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
T3sl4co1l
December 02, 2019, 10:51:33 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 02, 2019, 05:49:05 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
December 02, 2019, 04:10:14 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
December 02, 2019, 04:09:37 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 02, 2019, 03:42:16 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30