Author Topic: Transistors good for DRSSTC?  (Read 408 times)

Offline ritaismyconscience

  • High Voltage Enthusiast
  • *
  • Posts: 14
  • Karma: +0/-0
    • View Profile
Transistors good for DRSSTC?
« on: September 12, 2019, 05:53:51 AM »
So I found a good deal for these transistors:
https://www.mouser.com/datasheet/2/240/ixys_ds99525cixgq24n30pbix5187-1547450.pdf

The main problem I see with using this in a Tesla coil is that it's only rated for 300V. However, it can handle quite a bit of current. Is there anything I should be aware of before buying?

Offline Hydron

  • Administrator
  • High Voltage Engineer
  • *****
  • Posts: 273
  • Karma: +8/-0
    • View Profile
Re: Transistors good for DRSSTC?
« Reply #1 on: September 12, 2019, 08:44:48 AM »
The low voltage rating would be rather limiting, but the other issue I can see is the lack of an anti parallel diode, which is necessary for drsstc use. In theory an external diode could be used, but it's not worth the hassle when good IGBTs are available with them already integrated.

On another note, does anyone know what these parts are actually intended for (datasheet says "For PDP Applications")? The 300V limit is unusually low for an igbt!

Edit: PDP of course means plasma display panel, never mind my question!
« Last Edit: September 12, 2019, 08:46:46 AM by Hydron »

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1179
  • Karma: +17/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Transistors good for DRSSTC?
« Reply #2 on: September 12, 2019, 11:07:39 AM »
While they do look interesting to use in 120VAC countries there seems to be more cons than pros, simply due to the IGBTs getting destroyed from heat.

The 500Apeak rating is only specified for 10uS pulses
The legs are derated to a mere 75A

It is worth looking into paralleling these, obvious nice looking specs are gate charge, switching speed and Vce(sat)

I would worry the most about the Fmax2 calculation due to thermal limitations on this part, guide to calculate Fmax2: http://kaizerpowerelectronics.dk/tesla-coils/drsstc-design-guide/igbts/
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline Max

  • High Voltage Enthusiast
  • *
  • Posts: 24
  • Karma: +2/-0
    • View Profile
Re: Transistors good for DRSSTC?
« Reply #3 on: September 12, 2019, 12:47:03 PM »
Remember that these 75A are Arms. With 10% duty this equals around 580Apk (Source) - should be enough. Maybe for a 120V table top DRSSTC they work?


Kind regards,
Max

Offline ritaismyconscience

  • High Voltage Enthusiast
  • *
  • Posts: 14
  • Karma: +0/-0
    • View Profile
Re: Transistors good for DRSSTC?
« Reply #4 on: September 13, 2019, 05:50:53 AM »
I can also get these:
https://www.infineon.com/dgdl/Infineon-IKW75N60T-DS-v02_08-en.pdf?fileId=db3a304412b407950112b42890113e25

for about a third of the price. Seems like a better idea?

High Voltage Forum

Re: Transistors good for DRSSTC?
« Reply #4 on: September 13, 2019, 05:50:53 AM »

 


* Recent Topics and Posts

post Re: Royer oscillator (ZVS) driven Jacob's ladder, E80 core transformer
[Transformer (ferrite core)]
AndreiRS
Today at 03:59:49 AM
post How do you keep in contact with forum people...?
[General chatting]
AndreiRS
Today at 03:23:31 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
klugesmith
Today at 12:16:53 AM
post Re: My first DRSSTC on bricks
[Dual Resonant Solid State Tesla coils]
Laci
December 12, 2019, 08:35:24 PM
post Re: How To Make a Stencil For Spray Paint With Cheap Hand Tools
[General chatting]
johnf
December 12, 2019, 07:53:35 PM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
December 12, 2019, 02:52:58 PM
post Re: Royer oscillator (ZVS) driven Jacob's ladder, E80 core transformer
[Transformer (ferrite core)]
John123
December 12, 2019, 02:42:19 PM
post Re: Full bridge much "weaker" than half bridge?
[Solid state Tesla coils]
nick
December 12, 2019, 11:17:36 AM
post Re: Royer oscillator (ZVS) driven Jacob's ladder, E80 core transformer
[Transformer (ferrite core)]
davekni
December 12, 2019, 04:51:08 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
davekni
December 12, 2019, 04:26:22 AM
post Re: How To Make a Stencil For Spray Paint With Cheap Hand Tools
[General chatting]
AndreiRS
December 12, 2019, 01:21:35 AM
post Re: Using same winding on separate rails?
[Transformer (iron core)]
Twospoons
December 11, 2019, 10:49:04 PM
post Re: A dynamical arc model v2
[Dual Resonant Solid State Tesla coils]
Uspring
December 11, 2019, 05:28:46 PM
post Re: Full bridge much "weaker" than half bridge?
[Solid state Tesla coils]
Fumeaux
December 11, 2019, 03:11:42 PM
post Re: Royer oscillator (ZVS) driven Jacob's ladder, E80 core transformer
[Transformer (ferrite core)]
John123
December 11, 2019, 02:22:10 PM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
December 11, 2019, 02:09:19 PM
post Full bridge much "weaker" than half bridge?
[Solid state Tesla coils]
nick
December 11, 2019, 01:10:57 PM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
kamelryttarn
December 11, 2019, 08:48:36 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
December 11, 2019, 06:08:48 AM
post Re: SSTC low voltage at gate transformer and heating drivers
[Solid state Tesla coils]
davekni
December 11, 2019, 05:38:17 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
davekni
December 11, 2019, 05:01:31 AM
post Re: Using same winding on separate rails?
[Transformer (iron core)]
John123
December 11, 2019, 01:52:43 AM
post Re: Using same winding on separate rails?
[Transformer (iron core)]
klugesmith
December 11, 2019, 01:41:04 AM
post Re: Worlds Weirdest Microwave Oven, From A Weapons Factory - The Husqvarna Cupol
[Transformer (iron core)]
klugesmith
December 11, 2019, 01:37:13 AM
post Re: Using same winding on separate rails?
[Transformer (iron core)]
John123
December 11, 2019, 01:19:58 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 11, 2019, 01:14:32 AM
post Re: Using same winding on separate rails?
[Transformer (iron core)]
klugesmith
December 11, 2019, 01:04:08 AM
post Re: SSTC low voltage at gate transformer and heating drivers
[Solid state Tesla coils]
babass
December 10, 2019, 11:24:50 PM
post Using same winding on separate rails?
[Transformer (iron core)]
John123
December 10, 2019, 10:52:50 PM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
December 10, 2019, 03:35:40 PM
post Re: Why did 4HV die??
[General chatting]
John123
December 10, 2019, 03:21:07 PM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
Mads Barnkob
December 10, 2019, 03:04:28 PM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
December 10, 2019, 02:57:45 PM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
kamelryttarn
December 10, 2019, 11:23:48 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
Mads Barnkob
December 10, 2019, 10:27:54 AM
post Re: Worlds Weirdest Microwave Oven, From A Weapons Factory - The Husqvarna Cupol
[Transformer (iron core)]
Mads Barnkob
December 10, 2019, 10:20:17 AM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
Mads Barnkob
December 10, 2019, 10:16:32 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
December 10, 2019, 06:04:28 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
davekni
December 10, 2019, 05:28:54 AM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
davekni
December 10, 2019, 04:12:29 AM
post Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
December 09, 2019, 10:52:59 PM
post Replacement guide for Windows Media Center
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
MRMILSTAR
December 09, 2019, 08:29:16 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
Uspring
December 09, 2019, 04:23:33 PM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
MRMILSTAR
December 09, 2019, 03:59:02 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 09, 2019, 03:41:42 PM
post Possible use for large inductor (laminated core)
[Transformer (iron core)]
kamelryttarn
December 09, 2019, 09:43:11 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
December 09, 2019, 12:53:57 AM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
davekni
December 08, 2019, 09:57:51 PM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
MRMILSTAR
December 08, 2019, 05:28:09 PM
post Aethra CCD Webcam Teardown - From Back When Streaming Was Expensive!
[Electronic circuits]
Mads Barnkob
December 08, 2019, 01:33:30 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30