Author Topic: A problem solved with hand tools  (Read 288 times)

Offline klugesmith

  • High Voltage Enthusiast
  • *
  • Posts: 16
  • Karma: +0/-0
    • View Profile
A problem solved with hand tools
« on: July 15, 2019, 07:52:41 AM »
Is there a better sub-forum to discuss metalworking, and fabrication of things other than electric circuits?

The other day my old wet-or-dry Shop-Vac had a sudden failure.  Motor slowed down and started howling.  Probably time for a new vacuum cleaner.  But not before a good-faith attempt to fix the 25-year-old unit.  They don't make 'em like they used to, i.e. with tanks of steel instead of plastic.

Can't get to motor without removing the impeller, secured to shaft with a rusty old nut.  The impeller is hard to hold, in this model, because it's surrounded by molded plastic "stator blades".  Don't want to damage the thin sheet metal, nor have the circular edge slice into live human fingers when the grip slips.

Let's see if a jpg attachment, my first here, survives the upload and tells the story.  First use of the "chain" Vise-Grip tool that came my way some time in the last year.


[edit] So far so good.  Now about the second picture, revealing a very troubled bearing on this end:
p.s. Don't mix up the English words vise and vice.  Vise is a work-holding tool.  Vice is a personal habit, like smoking or drinking too much alcohol, that's considered bad for health or moral reasons. :-)  Like fuse and fuze, but that's another story.
« Last Edit: July 15, 2019, 08:06:41 AM by klugesmith »

Offline Hydron

  • Administrator
  • High Voltage Engineer
  • *****
  • Posts: 248
  • Karma: +7/-0
    • View Profile
Re: A problem solved with hand tools
« Reply #1 on: July 15, 2019, 11:21:29 AM »
The only tools like that I'd seen before were "chain whips" for working on bicycles (specifically for holding the sprockets for removal). Looks like a pretty handy tool, glad I know about it's existence now!

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1114
  • Karma: +17/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: A problem solved with hand tools
« Reply #2 on: July 15, 2019, 01:48:08 PM »
Nice to see a old unit, where you can actually repair it, gets repaired and put back in service :)

My father always had some of those in his garage, those were oil filter changing wrenches.

https://www.bahco.com/en/p/chain-oil-filter-wrench/ca-a5-b5-25-fa-c2-a1-5d-30-b5-60-9c-c3-85-d1-73/

http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline klugesmith

  • High Voltage Enthusiast
  • *
  • Posts: 16
  • Karma: +0/-0
    • View Profile
Re: A problem solved with hand tools
« Reply #3 on: August 12, 2019, 08:29:20 AM »
I gave up on that shop vac motor.  The ball bearing at near end had moved axially within molded plastic end bell.

Took the opportunity, yesterday, to get a picture of that chain tool, which locks tight with an adjustable over-center mechanism just like vise-grip pliers.  https://www.irwin.com/tools/locking-tools/the-original-locking-chain-clamp


« Last Edit: August 12, 2019, 08:42:01 AM by klugesmith »

Offline klugesmith

  • High Voltage Enthusiast
  • *
  • Posts: 16
  • Karma: +0/-0
    • View Profile
Re: A problem solved with hand tools
« Reply #4 on: August 26, 2019, 06:05:41 AM »
Hope this does not look like beating a dead horse.
For the picture in previous post, the vise-grip chain tool was too short to fit around the white plastic sleeve, so it had to go on the Pb-filled steel pipe that extends above the plastic.  Today it clamped onto the larger diameter section (circumference 19.8 inches or 503 mm), using a loose dowel pin in the last hole of the last link.
« Last Edit: August 26, 2019, 06:09:42 AM by klugesmith »

High Voltage Forum

Re: A problem solved with hand tools
« Reply #4 on: August 26, 2019, 06:05:41 AM »

 


* Recent Topics and Posts

post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
September 18, 2019, 07:27:46 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
September 18, 2019, 06:56:20 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
September 18, 2019, 05:08:06 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
September 18, 2019, 01:35:58 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
September 18, 2019, 05:54:23 AM
post Re: Blast from the past!
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
klugesmith
September 18, 2019, 05:05:55 AM
post Re: UD2.7 Gate Signals
[Dual Resonant Solid State Tesla coils]
coilinator
September 17, 2019, 08:24:59 PM
post Re: Blast from the past!
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
MRMILSTAR
September 17, 2019, 08:19:45 PM
post Re: Blast from the past!
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Mads Barnkob
September 17, 2019, 06:53:52 PM
post Blast from the past!
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
MRMILSTAR
September 17, 2019, 05:52:00 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
September 17, 2019, 05:00:47 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
davekni
September 17, 2019, 06:48:38 AM
post Re: My second DRSSTC
[Dual Resonant Solid State Tesla coils]
erdal
September 16, 2019, 11:07:27 PM
post Re: 750W solar offgrid 24V/150Ah battery setup with Victron charger
[Electronic circuits]
johnf
September 16, 2019, 09:48:37 PM
post Re: adventures in homemade flyback bobbins.
[Transformer (ferrite core)]
AlexanderHun
September 16, 2019, 10:42:44 AM
post Re: Offgrid 48V solar to 24V battery setup
[Electronic circuits]
Mads Barnkob
September 16, 2019, 09:40:27 AM
post Re: My second DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
September 16, 2019, 09:28:43 AM
post Re: Large Ferrite Core with IGBT-Brick Driver
[Transformer (ferrite core)]
Mads Barnkob
September 16, 2019, 09:24:17 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
T3sl4co1l
September 16, 2019, 06:59:12 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
davekni
September 16, 2019, 04:18:26 AM
post Re: My second DRSSTC
[Dual Resonant Solid State Tesla coils]
davekni
September 16, 2019, 02:49:28 AM
post Re: Large Ferrite Core with IGBT-Brick Driver
[Transformer (ferrite core)]
davekni
September 16, 2019, 02:43:18 AM
post Re: Homemade HV transformer
[Transformer (ferrite core)]
davekni
September 16, 2019, 02:36:17 AM
post Re: adventures in homemade flyback bobbins.
[Transformer (ferrite core)]
davekni
September 16, 2019, 02:26:40 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
September 16, 2019, 01:50:19 AM
post Re: UD2.7 Gate Signals
[Dual Resonant Solid State Tesla coils]
coilinator
September 15, 2019, 08:22:47 PM
post Re: My second DRSSTC
[Dual Resonant Solid State Tesla coils]
erdal
September 15, 2019, 02:09:17 PM
post Re: Homemade HV transformer
[Transformer (ferrite core)]
AlexanderHun
September 15, 2019, 10:39:29 AM
post Re: Homemade HV transformer
[Transformer (ferrite core)]
ElectroXa
September 14, 2019, 07:01:28 PM
post Re: adventures in homemade flyback bobbins.
[Transformer (ferrite core)]
AlexanderHun
September 14, 2019, 06:59:13 PM
post Re: Homemade HV transformer
[Transformer (ferrite core)]
AlexanderHun
September 14, 2019, 06:43:15 PM
post Re: Homemade HV transformer
[Transformer (ferrite core)]
ritaismyconscience
September 14, 2019, 06:35:32 PM
post Homemade HV transformer
[Transformer (ferrite core)]
AlexanderHun
September 14, 2019, 05:05:00 PM
post Re: UD2.7 Gate Signals
[Dual Resonant Solid State Tesla coils]
profdc9
September 14, 2019, 04:50:10 PM
post Re: UD2.7 Gate Signals
[Dual Resonant Solid State Tesla coils]
coilinator
September 14, 2019, 08:42:55 AM
post Re: Transistors good for DRSSTC?
[Dual Resonant Solid State Tesla coils]
ritaismyconscience
September 13, 2019, 05:50:53 AM
post Re: Transistors good for DRSSTC?
[Dual Resonant Solid State Tesla coils]
Max
September 12, 2019, 12:47:03 PM
post Re: Transistors good for DRSSTC?
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
September 12, 2019, 11:07:39 AM
post Re: "karma", "applause/smite" button meaning and use
[General chatting]
Mads Barnkob
September 12, 2019, 11:01:05 AM
post Re: Transistors good for DRSSTC?
[Dual Resonant Solid State Tesla coils]
Hydron
September 12, 2019, 08:44:48 AM
post Transistors good for DRSSTC?
[Dual Resonant Solid State Tesla coils]
ritaismyconscience
September 12, 2019, 05:53:51 AM
post Re: "karma", "applause/smite" button meaning and use
[General chatting]
oneKone
September 12, 2019, 05:37:11 AM
post "karma", "applause/smite" button meaning and use
[General chatting]
MRMILSTAR
September 12, 2019, 05:07:24 AM
post Re: Why did 4HV die??
[General chatting]
oneKone
September 12, 2019, 04:50:24 AM
post Drsstc 4, I'm never stopping
[Dual Resonant Solid State Tesla coils]
oneKone
September 12, 2019, 02:36:00 AM
post Re: Why did 4HV die??
[General chatting]
Hydron
September 12, 2019, 12:34:10 AM
post Re: Why did 4HV die??
[General chatting]
MRMILSTAR
September 11, 2019, 09:29:40 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
MRMILSTAR
September 11, 2019, 09:00:31 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
coilinator
September 11, 2019, 07:54:30 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
freq_out
September 11, 2019, 05:40:14 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30