Author Topic: tesla coil varnish is dumb  (Read 1405 times)

Offline Fumeaux

  • High Voltage Experimenter
  • **
  • Posts: 76
  • Karma: +7/-0
    • View Profile
tesla coil varnish is dumb
« on: July 14, 2019, 05:29:10 PM »
Dear High Voltage Forum!

Some time ago I started to wind a new coil. I chose a PU-dispersion paint, which turned out to be a mistake. My guess is that normal PU-paint would have worked, but the watersolvable-dispersion-stuff didn't. Now my coil has countless fingernail wide cracks. I don't think that is that big of an issue, as I have a layer of electricaltape underneath to make it structurally sound. But I'm still worried about the insulation aspect. That's why I'm asking for your thoughts on this.



Does anybody think is should fix it? And what do you suggest?

I can't reccomend this lacker.

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1512
  • Karma: +26/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: tesla coil varnish is dumb
« Reply #1 on: July 14, 2019, 08:20:52 PM »
I tried something similar once, where I tried to fix it with a different type of varnish and that was just another mistake on a mistake. I used a oil based furniture varnish first and when that failed I tried to add spray on polyurethane and that just cracked up everywhere!

Since it cracks its either reacting with the electrical tape or you had huge temperature differences?

Fixing it.... hmm, try to fill out the cracks with another varnish type and just live with the fact that it will never be pretty :)

You have a sad doggo in the varnish.

http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline T3sl4co1l

  • High Voltage Technician
  • ***
  • Posts: 153
  • Karma: +9/-0
    • View Profile
Re: tesla coil varnish is dumb
« Reply #2 on: July 14, 2019, 09:59:40 PM »
Huh.  What's the point of varnishing the outside, if there's air between the wires, under the tape?

I have one experience with water-based urethane; I was thoroughly underwhelmed by its performance.  It cost much more, went on much thinner (it's mostly water, so the dried film is quite thin and many coats are needed), is softer (though still strong enough not to be peeled off by fingernails alone), and seems to turn a bit gooey/sticky with prolonged contact with oils.

There probably are better-performing mixes, and I happened to get the worst one out there.  Ironically, I feel like the stuff I had, wouldn't have given you trouble -- it doesn't seem brittle enough to crack.  But then again, vinyl tape is rich with plasticizers (basically, oils that turn the plastic gooey -- pure PVC is a brittle white solid -- see where this is going?), and maybe that's strained or weakened your coating, causing it to crack.

Varnish is kind of dumb anyway, since at the voltages we're talking here, you need whole cm's of thickness to effectively insulate something.  Modest layers can still provide some protection, such as corona suppression or protecting against smaller streamers; I don't have enough experience in this direction to know how significant this is, so I'll let others fill in.

Tim

Offline Hydron

  • Administrator
  • High Voltage Engineer
  • *****
  • Posts: 345
  • Karma: +11/-0
    • View Profile
Re: tesla coil varnish is dumb
« Reply #3 on: July 14, 2019, 10:49:03 PM »
Huh.  What's the point of varnishing the outside, if there's air between the wires, under the tape?
Kizmo kinda got around this by making a pipe lathe to cut a groove for a spaced secondary winding, which both cut down the secondary impedance and also gave better insulation properties (as there were spaces between turns for varnish to fill).

I tend to agree that varnish is probably fairly futile from an electrical insulation perspective, but in terms of holding the coil together mechanically it makes sense. Especially if you have the coil on a motorised winding jig it's pretty easy to slap on some polyurethane or epoxy to hold the windings together and give some protection from minor scrapes etc.

Offline Teravolt

  • High Voltage Technician
  • ***
  • Posts: 124
  • Karma: +2/-0
    • View Profile
Re: tesla coil varnish is dumb
« Reply #4 on: August 27, 2019, 09:32:41 PM »
I just use minwax urithane in a spray can just after winding to hold the windings in place not to insulate.  the wire will strech after winding and I have had coils unravle

Offline MRMILSTAR

  • High Voltage Engineer
  • ****
  • Posts: 213
  • Karma: +4/-0
  • Cedar Rapids, Iowa
    • View Profile
Re: tesla coil varnish is dumb
« Reply #5 on: October 10, 2019, 05:26:08 AM »
Varnish is not for insulation. It is used to hold the coil windings in place during temperature extremes. If you don't varnish the coil, a big temperature swing can actually cause your secondary windings to collapse and fall off of the form. This has happened to a number of people.
« Last Edit: October 10, 2019, 08:47:56 PM by MRMILSTAR »
Steve White
Cedar Rapids, Iowa
Retired electrical engineer

High Voltage Forum

Re: tesla coil varnish is dumb
« Reply #5 on: October 10, 2019, 05:26:08 AM »

 


* Recent Topics and Posts

post Re: Rogowski current probe
[Laboratories, Equipment and Tools]
Hydron
Today at 05:27:37 PM
post Re: DRSSTC Tuning for Music vs Big Sparks?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Zipdox
Today at 04:32:53 PM
post Re: DRSSTC Tuning for Music vs Big Sparks?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
Today at 04:17:51 PM
post Re: DRSSTC Tuning for Music vs Big Sparks?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
GKnapp
Today at 02:06:04 PM
post Re: Rogowski current probe
[Laboratories, Equipment and Tools]
flyglas
Today at 10:57:58 AM
post Re: DRSSTC Tuning for Music vs Big Sparks?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
Today at 08:55:27 AM
post Re: DRSSTC Tuning for Music vs Big Sparks?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
Today at 05:19:45 AM
post Re: Rogowski current probe
[Laboratories, Equipment and Tools]
klugesmith
Today at 04:46:12 AM
post Re: Easy to build Polyphonic MIDI Interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Max
Today at 01:14:47 AM
post Re: Rogowski current probe
[Laboratories, Equipment and Tools]
flyglas
September 25, 2020, 09:41:10 PM
post Re: DRSSTC Tuning for Music vs Big Sparks?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
September 25, 2020, 08:40:39 PM
post Re: Easy to build Polyphonic MIDI Interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Mads Barnkob
September 25, 2020, 08:26:52 PM
post Re: FPGA speeds these days?
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
SteveN87
September 25, 2020, 06:56:41 PM
post Re: FPGA speeds these days?
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
klugesmith
September 25, 2020, 06:15:47 PM
post Re: FPGA speeds these days?
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
SteveN87
September 25, 2020, 01:56:27 PM
post Re: FPGA speeds these days?
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
TMaxElectronics
September 25, 2020, 11:55:05 AM
post Re: FPGA speeds these days?
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Weston
September 25, 2020, 09:18:51 AM
post One NOS ac flyback is nice. Finding its identical twin 3 months later is awesome
[Transformer (Ferrite Core)]
extremeodd
September 25, 2020, 03:43:26 AM
post Re: FPGA speeds these days?
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
davekni
September 25, 2020, 03:42:56 AM
post FPGA speeds these days?
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
klugesmith
September 25, 2020, 02:13:40 AM
post Re: Server PSU OPV Hack - Fujitsu DPS-800GB-5 A
[Electronic Circuits]
klugesmith
September 24, 2020, 03:02:00 PM
post Re: Server PSU OPV Hack - Fujitsu DPS-800GB-5 A
[Electronic Circuits]
v.coelho
September 24, 2020, 01:11:27 PM
post Re: Info needed: probably old military High Voltage Multiplier?
[Voltage Multipliers]
Zipdox
September 24, 2020, 10:25:42 AM
post Re: Info needed: probably old military High Voltage Multiplier?
[Voltage Multipliers]
johnnyzoo
September 24, 2020, 07:32:43 AM
post Re: Current transformer for narrow spaces
[Laboratories, Equipment and Tools]
klugesmith
September 23, 2020, 11:20:53 PM
post WTS [US]:"Terry filter" varistors for sale
[Sell / Buy / Trade]
MRMILSTAR
September 23, 2020, 10:41:54 PM
post Re: Info needed: probably old military High Voltage Multiplier?
[Voltage Multipliers]
Zipdox
September 23, 2020, 10:25:07 PM
post Info needed: probably old military High Voltage Multiplier?
[Voltage Multipliers]
HighVoltageRulezz
September 23, 2020, 10:06:30 PM
post Re: Server PSU OPV Hack - Fujitsu DPS-800GB-5 A
[Electronic Circuits]
petespaco
September 23, 2020, 04:26:34 PM
post Re: 6" Coil Update now 72" and better lighting
[Spark Gap Tesla Coils (SGTC)]
klugesmith
September 23, 2020, 03:06:28 PM
post Re: Server PSU OPV Hack - Fujitsu DPS-800GB-5 A
[Electronic Circuits]
Zipdox
September 23, 2020, 01:34:42 PM
post Server PSU OPV Hack - Fujitsu DPS-800GB-5 A
[Electronic Circuits]
v.coelho
September 23, 2020, 01:11:50 PM
post 6" Coil Update now 72" and better lighting
[Spark Gap Tesla Coils (SGTC)]
Bradselph
September 23, 2020, 09:03:56 AM
post Re: steam engine
[Capacitor Banks]
plasma
September 23, 2020, 12:53:49 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic Circuits]
extremeodd
September 23, 2020, 12:35:16 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic Circuits]
petespaco
September 22, 2020, 08:15:40 PM
post Re: Am I Misunderstanding of DC Blocking Capacitors
[Solid State Tesla Coils (SSTC)]
klugesmith
September 22, 2020, 05:59:21 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic Circuits]
klugesmith
September 22, 2020, 05:42:28 PM
post Re: Am I Misunderstanding of DC Blocking Capacitors
[Solid State Tesla Coils (SSTC)]
T3sl4co1l
September 22, 2020, 06:48:34 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic Circuits]
petespaco
September 22, 2020, 01:48:11 AM
post Re: steam engine
[Capacitor Banks]
klugesmith
September 21, 2020, 11:58:09 PM
post Re: steam engine
[Capacitor Banks]
plasma
September 21, 2020, 11:21:28 PM
post Re: steam engine
[Capacitor Banks]
HiVi
September 21, 2020, 08:30:22 PM
post Re: steam engine
[Capacitor Banks]
klugesmith
September 21, 2020, 07:11:30 PM
post Re: Am I Misunderstanding of DC Blocking Capacitors
[Solid State Tesla Coils (SSTC)]
klugesmith
September 21, 2020, 06:57:13 PM
post Re: DRSSTC Tuning for Music vs Big Sparks?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Uspring
September 21, 2020, 05:50:56 PM
post Re: Easy to build Polyphonic MIDI Interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Max
September 21, 2020, 02:59:47 PM
post Re: VTTC on GU-81M
[Vacuum Tube Tesla Coils (VTTC)]
Continuum
September 21, 2020, 12:18:10 PM
post Re: steam engine
[Capacitor Banks]
plasma
September 21, 2020, 09:49:57 AM
post Re: steam engine
[Capacitor Banks]
Zipdox
September 21, 2020, 09:18:53 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal