Author Topic: Bought huge capacitors  (Read 301 times)

Offline ritaismyconscience

  • High Voltage Enthusiast
  • *
  • Posts: 10
  • Karma: +0/-0
    • View Profile
Bought huge capacitors
« on: June 12, 2019, 03:02:50 AM »
http://imgur.com/gallery/OcA4IgW

I bought these 15600uF 2800v for 50 dollars each and I was wondering what kind of project I should build with them. I probably won't be able to afford scrs and switching 100kj is likely not easy. Any ideas?

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1021
  • Karma: +16/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Bought huge capacitors
« Reply #1 on: June 12, 2019, 10:56:39 AM »
First, congratulations on a bargain buy there! I will buy them off you if shipping isn't a killer!

I got some good papers collected on high current discharges, especially the one on erosion is interesting when it comes to designing spark gaps: http://kaizerpowerelectronics.dk/tools/file-archive/?drawer=application_notes*pulse_power

One of these capacitors is obvious choice as DC bus capacitor in a large DRSSTC, as in serisouly large, multiply 600-1200A IGBTs in parallel, 5-6 meters tall, so might not be the project you are looking for. Or build your own electric car.

Ring launchers, can crushers etc. utilizes lower voltage better as you have less flash-over of the work coil, so there is always that.
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline Hydron

  • Administrator
  • High Voltage Engineer
  • *****
  • Posts: 231
  • Karma: +6/-0
    • View Profile
Re: Bought huge capacitors
« Reply #2 on: June 12, 2019, 01:52:33 PM »
My 2c:
- very nice score!
- take those safety warnings seriously
- play around with mechanical switching, triggered spark gaps etc. This sort of energy is probably beyond normal SCR territory anyway!

Offline ritaismyconscience

  • High Voltage Enthusiast
  • *
  • Posts: 10
  • Karma: +0/-0
    • View Profile
Re: Bought huge capacitors
« Reply #3 on: June 12, 2019, 06:38:07 PM »
One of my other concerns is that my neighbors would get mad at me (it'll probably sound like an explosion)

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1021
  • Karma: +16/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Bought huge capacitors
« Reply #4 on: June 12, 2019, 09:48:22 PM »
One of my other concerns is that my neighbors would get mad at me (it'll probably sound like an explosion)

More in the region of gun shot, it does not get that deep boom from a huge displacement of a lot of air, it is a sharp metallic snapping from the intense and short lived short circuit energy discharge.

With some soft materials around, which can also act as blast shields, you can absorb a lot of sound. Even just a closed door to a garage will take most of it.

Also, take safety serious as Hydron says, these energy levels can remove your hand or any other flesh that becomes a conductor.
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline badpeter

  • High Voltage Enthusiast
  • *
  • Posts: 27
  • Karma: +1/-0
    • View Profile
Re: Bought huge capacitors
« Reply #5 on: June 13, 2019, 06:14:58 PM »
This immediately reminds me of youtuber "PhotonicInduction" who does all kinds of very odd things with crazy parts like that!

Offline Max

  • High Voltage Enthusiast
  • *
  • Posts: 23
  • Karma: +2/-0
    • View Profile
Re: Bought huge capacitors
« Reply #6 on: June 16, 2019, 12:25:59 PM »
Some time ago I visited a high voltage lab. Beside highly interesting things like a 900kV transformer they also had a few serious cap banks. One of them was used to blow up an Aluminium wire with 30kJ. We stand a few meters away and the "boom" was deep and intense enough to be felt in the whole body. There was much more energy released because the aluminium reacts with the oxygen - and as it's evaporated and very hot it does this rather quickly ;)

Outdoors the sound might be sharper, but it definetly has nothing to do with your <5kJ home made cap banks.


Kind regards,
Max

Offline MRMILSTAR

  • High Voltage Enthusiast
  • *
  • Posts: 14
  • Karma: +0/-0
  • Cedar Rapids, Iowa
    • View Profile
Re: Bought huge capacitors
« Reply #7 on: June 16, 2019, 06:07:06 PM »
Switching a high energy at low voltage like that is definitely a challenge. My quarter shrinker uses 2 brass electrodes, each of which is 2 inches in diameter. I can move them as close as 1 mm with good precision but that is not good enough for your low voltage capacitors unless you can make a switch with enough precision to achieve sub-millimeter spacing without touching. Normally, you don't want the electrodes to touch when firing to prevent welding. I only see 2 options for your low voltage: triggered gap or contact switch.

I haven't seen any triggered gaps that operate at these low voltages (<2500 volts). You may be able to build one but it would take some experimentation.

The other option is a contact switch. You can make a sacrificial switch that welds each time it is used. This is not very attractive because it would have ti be replaced after each firing. Another possibility is the use of pure tungsten electrodes. These might be able to make contact without welding. I don't know. Even if it would work, large tungsten electrodes would be expensive. Perhaps you could cut up some tungsten welding rods and use the rods in parallel to make a large electrode.

Offline dexter

  • High Voltage Enthusiast
  • *
  • Posts: 22
  • Karma: +2/-0
    • View Profile
Re: Bought huge capacitors
« Reply #8 on: June 16, 2019, 08:25:16 PM »
in a 2015 post from 4hv by Kizmo about triggered spark gaps he says it works at any capacitor voltage even as low as 20V
https://4hv.org/e107_plugins/forum/forum_viewtopic.php?p=1&id=171055#post-171722

also saw some russians playing with a homemade taser on the mains wiring of their house which had the same effect as a triggered spark gap

Offline MRMILSTAR

  • High Voltage Enthusiast
  • *
  • Posts: 14
  • Karma: +0/-0
  • Cedar Rapids, Iowa
    • View Profile
Re: Bought huge capacitors
« Reply #9 on: June 17, 2019, 04:34:02 PM »
Triggered spark gaps make me nervous. They don't seem to be extremely reliable. Most of the time they fire but sometimes they don't. When they don't, you're sitting there with a huge capacitor with massive energy stored in it. Then you have to figure out a way to discharge it. That's why I use a simple 2-electrode switch that depends only on proximity to fire. Of course any impulse energy device such as this should have a way to safely and slowly discharge a fully-charged capacitor bank. I use a group of power resistors.

Given your low maximum voltage, a triggered spark gap may be your best option if you can make it work reliably and without destroying the trigger circuit.

High Voltage Forum

Re: Bought huge capacitors
« Reply #9 on: June 17, 2019, 04:34:02 PM »

 


* Recent Topics and Posts

post Re: "LightningStorm" VTTC project
[Vacuum tube Tesla coils]
Avenger
Today at 03:18:07 PM
post Re: Onetesla TS driver board for OWN coil need some help
[Dual Resonant Solid State Tesla coils]
donnersm
Today at 03:18:03 PM
post Re: Onetesla TS driver board for OWN coil need some help
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
Today at 02:56:29 PM
post Re: SSTC interruptor not working
[Solid state Tesla coils]
Mads Barnkob
Today at 11:46:44 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Mads Barnkob
Today at 11:45:11 AM
post Re: "LightningStorm" VTTC project
[Vacuum tube Tesla coils]
Mads Barnkob
Today at 11:40:18 AM
post Re: My first DRSSTC on bricks
[Dual Resonant Solid State Tesla coils]
Netzpfuscher
Today at 07:46:25 AM
post Re: Si-wafers, ideas?
[Electronic circuits]
Weston
Today at 07:07:57 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
hightemp1
Today at 05:45:55 AM
post Re: My first DRSSTC on bricks
[Dual Resonant Solid State Tesla coils]
Laci
June 24, 2019, 09:26:47 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
Bert911
June 24, 2019, 04:58:39 PM
post Re: Static electricity measurement
[Static electricity]
Doros
June 24, 2019, 01:56:17 PM
post Re: "LightningStorm" VTTC project
[Vacuum tube Tesla coils]
Avenger
June 24, 2019, 01:28:59 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Patrick
June 24, 2019, 12:47:16 AM
post SSTC interruptor not working
[Solid state Tesla coils]
juuzpo
June 23, 2019, 10:58:48 PM
post Re: Is one of these good?
[Dual Resonant Solid State Tesla coils]
Golddustpeak
June 23, 2019, 07:22:47 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Jeff B
June 23, 2019, 05:52:56 PM
post Re: Onetesla TS driver board for OWN coil need some help
[Dual Resonant Solid State Tesla coils]
dexter
June 23, 2019, 03:15:53 PM
post Onetesla TS driver board for OWN coil need some help
[Dual Resonant Solid State Tesla coils]
donnersm
June 23, 2019, 10:09:40 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Patrick
June 23, 2019, 10:07:04 AM
post Vacuum Epoxy Potting Attempt in Progress... (Pic Update 6/23/19)
[Transformer (ferrite core)]
Patrick
June 23, 2019, 08:50:14 AM
post Re: Si-wafers, ideas?
[Electronic circuits]
johnf
June 23, 2019, 01:28:20 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Twospoons
June 23, 2019, 01:17:50 AM
post Re: Si-wafers, ideas?
[Electronic circuits]
Twospoons
June 23, 2019, 01:04:13 AM
post Re: What happens when L and C are not matched?
[Electronic circuits]
Twospoons
June 23, 2019, 01:02:55 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Coupling
June 22, 2019, 11:10:02 PM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
flyrod
June 22, 2019, 08:45:17 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
flyrod
June 22, 2019, 08:36:34 PM
post Impressive 500,000 watt radio station from the 1930's
[Electronic circuits]
petespaco
June 22, 2019, 06:18:22 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
hightemp1
June 22, 2019, 05:47:22 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
T3sl4co1l
June 22, 2019, 05:21:58 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
hightemp1
June 22, 2019, 06:10:01 AM
post Re: Siemens Polyphos 30 xray machine
[X-ray]
Mads Barnkob
June 21, 2019, 09:08:16 AM
post Re: Choke-input DC-filter
[Electronic circuits]
johnf
June 20, 2019, 08:58:07 PM
post Re: CRT hacking ideas....
[Electronic circuits]
badpeter
June 20, 2019, 07:28:00 PM
post Re: Ideas needed!
[General chatting]
MRMILSTAR
June 20, 2019, 05:13:57 PM
post Re: Why did 4HV die??
[General chatting]
MRMILSTAR
June 20, 2019, 05:07:41 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
Bert911
June 20, 2019, 02:14:55 PM
post Re: Choke-input DC-filter
[Electronic circuits]
kamelryttarn
June 20, 2019, 12:53:58 PM
post Re: Choke-input DC-filter
[Electronic circuits]
johnf
June 20, 2019, 12:09:27 PM
post Choke-input DC-filter
[Electronic circuits]
kamelryttarn
June 20, 2019, 11:43:58 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
shrad
June 20, 2019, 08:57:42 AM
post Re: adventures in homemade flyback bobbins.
[Transformer (ferrite core)]
Patrick
June 20, 2019, 04:06:00 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
johnf
June 20, 2019, 03:50:56 AM
post Re: CRT hacking ideas....
[Electronic circuits]
petespaco
June 19, 2019, 11:29:28 PM
post Re: A dynamical arc model v2
[Dual Resonant Solid State Tesla coils]
Uspring
June 19, 2019, 01:40:16 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Mads Barnkob
June 19, 2019, 10:49:45 AM
post Re: A dynamical arc model v2
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
June 19, 2019, 10:43:32 AM
post Re: Light, laser and optics - Link collection
[Light, lasers and optics]
shrad
June 19, 2019, 10:03:54 AM
post Re: How go get single mode optic fiber to work
[Light, lasers and optics]
shrad
June 19, 2019, 10:02:21 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30