Author Topic: Flat Secondary Coil on PCB?  (Read 288 times)

Offline profdc9

  • High Voltage Engineer
  • ****
  • Posts: 216
  • Karma: +10/-0
    • View Profile
Flat Secondary Coil on PCB?
« on: May 01, 2019, 05:54:26 PM »
I was thinking about designing a small kit-based Tesla coil where rather than the seconary coil being a solenoid, it is a flat spiral.  Of course the secondary inductance goes down, but is there any reason this shouldn't work?  Flat spirals are already used for resonant power transfer applications (e.g. wireless charging and induction cookers).

The board I designed has (I calculate) about 1 mH of inductance.  It is about 150 turns of 0.13 mm wide traces separated by 0.15 mm.  This is the thinnest I could fit in the design rules of the process.

Anyways I was up late last night and drew up a PCB.  The hole in the middle is for a post to put the topload on sticking up from the PCB.  The hole on the edge is to connect the ground.  There is a six turn coil on the back that is used to sense the current in the secondary for feedback purposes.

I was thinking too that I could stack the boards to get more turns and place a thick HDPE insulator between them.    The center of each coil would be connected to the ground of the next in series, and these would be stacked as to be placed over the primary coil  so that the board would intersect  the magnetic field lines of the primary coil.

Here is what I drew up last night:



Any comments about this design?  I want to call it the "Conversation Piece" which would be a little tabletop SSTC coil.  It would be powered by 12-30 VAC.

Dan

Offline Phoenix

  • High Voltage Experimenter
  • **
  • Posts: 63
  • Karma: +1/-0
    • View Profile

Offline profdc9

  • High Voltage Engineer
  • ****
  • Posts: 216
  • Karma: +10/-0
    • View Profile
Re: Flat Secondary Coil on PCB?
« Reply #2 on: May 01, 2019, 07:34:33 PM »
You wouldn't happen to know of a video of it in use?  I am curious to see how they work.  I was thinking of adding a buck converter before the half/full bridge so that I could modulate the power with an audio signal.

Dan

Hello

I know that such tesla coils work, because they are sold commercially: https://highvoltageshop.com/epages/b73088c0-9f9a-4230-9ffc-4fd5c619abc4.sf/de_DE/?ObjectPath=/Shops/b73088c0-9f9a-4230-9ffc-4fd5c619abc4/Products/TESLA_MINI_v1.2_

In the description you can see the technical data of the coil, it has 120 turns: https://highvoltageshop.com/epages/b73088c0-9f9a-4230-9ffc-4fd5c619abc4.sf/de_DE/?ObjectPath=/Shops/b73088c0-9f9a-4230-9ffc-4fd5c619abc4/Products/TC12_flach

Greetings
Phoenix

Offline Phoenix

  • High Voltage Experimenter
  • **
  • Posts: 63
  • Karma: +1/-0
    • View Profile
Re: Flat Secondary Coil on PCB?
« Reply #3 on: May 01, 2019, 08:17:27 PM »
No, i do not have a video about this coil. But if you look at the image from the second link, you can see that the primary is on the same PCB as the secondary. There are 2 bigger traces after the secondary coil.

The description says that this is a class E SSTC. I think you could use any normal Audio PLL Class E SSTC schematic and simply hook this coil up instead of a classical resonator: http://uzzors2k.4hv.org/projectfiles/classesstc1/classE_SSTC.GIF

Maybe you need to adjust some component values according to your resonant frequency, but the basic principle is the same.

Greetings
Phoenix

Offline oneKone

  • High Voltage Engineer
  • ****
  • Posts: 249
  • Karma: +5/-0
    • View Profile
Re: Flat Secondary Coil on PCB?
« Reply #4 on: May 02, 2019, 01:24:07 AM »
The only thing I can offer here is another reference. This coil is still early days but it is a drsstc.
https://hackaday.io/project/165112-pcbtc-gan-edition

Offline profdc9

  • High Voltage Engineer
  • ****
  • Posts: 216
  • Karma: +10/-0
    • View Profile
Re: Flat Secondary Coil on PCB?
« Reply #5 on: May 02, 2019, 02:06:27 AM »
The only thing I can offer here is another reference. This coil is still early days but it is a drsstc.
https://hackaday.io/project/165112-pcbtc-gan-edition

Thanks for the link.  That looks like an awesome project.

Thanks to you both for the info.  It gives food for thought.  I didn't think I was the only one who thought of this, but obviously there's been some movement here. :)

I was thinking of keeping the primary and secondary on separate PCBs so I could stack several secondaries to get more turns, and also I put the sense coil on the other side of the secondary board so that it there is less of a chance of having a coil strike damage the circuity (if it is possible to have a streamer that long).

dan

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1021
  • Karma: +16/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Flat Secondary Coil on PCB?
« Reply #6 on: June 04, 2019, 09:04:46 AM »
You could stack multiply PCBs as its done with planar transformers where the PCB are connected with VIA and the primary/secondary are interleaved for highest possible coupling.

I know this might not work as well with a high voltage output like this, but at least it is a common used practise to make these electronic layer cakes.
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

High Voltage Forum

Re: Flat Secondary Coil on PCB?
« Reply #6 on: June 04, 2019, 09:04:46 AM »

 


* Recent Topics and Posts

post Re: "LightningStorm" VTTC project
[Vacuum tube Tesla coils]
Avenger
Today at 03:18:07 PM
post Re: Onetesla TS driver board for OWN coil need some help
[Dual Resonant Solid State Tesla coils]
donnersm
Today at 03:18:03 PM
post Re: Onetesla TS driver board for OWN coil need some help
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
Today at 02:56:29 PM
post Re: SSTC interruptor not working
[Solid state Tesla coils]
Mads Barnkob
Today at 11:46:44 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Mads Barnkob
Today at 11:45:11 AM
post Re: "LightningStorm" VTTC project
[Vacuum tube Tesla coils]
Mads Barnkob
Today at 11:40:18 AM
post Re: My first DRSSTC on bricks
[Dual Resonant Solid State Tesla coils]
Netzpfuscher
Today at 07:46:25 AM
post Re: Si-wafers, ideas?
[Electronic circuits]
Weston
Today at 07:07:57 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
hightemp1
Today at 05:45:55 AM
post Re: My first DRSSTC on bricks
[Dual Resonant Solid State Tesla coils]
Laci
June 24, 2019, 09:26:47 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
Bert911
June 24, 2019, 04:58:39 PM
post Re: Static electricity measurement
[Static electricity]
Doros
June 24, 2019, 01:56:17 PM
post Re: "LightningStorm" VTTC project
[Vacuum tube Tesla coils]
Avenger
June 24, 2019, 01:28:59 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Patrick
June 24, 2019, 12:47:16 AM
post SSTC interruptor not working
[Solid state Tesla coils]
juuzpo
June 23, 2019, 10:58:48 PM
post Re: Is one of these good?
[Dual Resonant Solid State Tesla coils]
Golddustpeak
June 23, 2019, 07:22:47 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Jeff B
June 23, 2019, 05:52:56 PM
post Re: Onetesla TS driver board for OWN coil need some help
[Dual Resonant Solid State Tesla coils]
dexter
June 23, 2019, 03:15:53 PM
post Onetesla TS driver board for OWN coil need some help
[Dual Resonant Solid State Tesla coils]
donnersm
June 23, 2019, 10:09:40 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Patrick
June 23, 2019, 10:07:04 AM
post Vacuum Epoxy Potting Attempt in Progress... (Pic Update 6/23/19)
[Transformer (ferrite core)]
Patrick
June 23, 2019, 08:50:14 AM
post Re: Si-wafers, ideas?
[Electronic circuits]
johnf
June 23, 2019, 01:28:20 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Twospoons
June 23, 2019, 01:17:50 AM
post Re: Si-wafers, ideas?
[Electronic circuits]
Twospoons
June 23, 2019, 01:04:13 AM
post Re: What happens when L and C are not matched?
[Electronic circuits]
Twospoons
June 23, 2019, 01:02:55 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Coupling
June 22, 2019, 11:10:02 PM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
flyrod
June 22, 2019, 08:45:17 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
flyrod
June 22, 2019, 08:36:34 PM
post Impressive 500,000 watt radio station from the 1930's
[Electronic circuits]
petespaco
June 22, 2019, 06:18:22 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
hightemp1
June 22, 2019, 05:47:22 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
T3sl4co1l
June 22, 2019, 05:21:58 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
hightemp1
June 22, 2019, 06:10:01 AM
post Re: Siemens Polyphos 30 xray machine
[X-ray]
Mads Barnkob
June 21, 2019, 09:08:16 AM
post Re: Choke-input DC-filter
[Electronic circuits]
johnf
June 20, 2019, 08:58:07 PM
post Re: CRT hacking ideas....
[Electronic circuits]
badpeter
June 20, 2019, 07:28:00 PM
post Re: Ideas needed!
[General chatting]
MRMILSTAR
June 20, 2019, 05:13:57 PM
post Re: Why did 4HV die??
[General chatting]
MRMILSTAR
June 20, 2019, 05:07:41 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
Bert911
June 20, 2019, 02:14:55 PM
post Re: Choke-input DC-filter
[Electronic circuits]
kamelryttarn
June 20, 2019, 12:53:58 PM
post Re: Choke-input DC-filter
[Electronic circuits]
johnf
June 20, 2019, 12:09:27 PM
post Choke-input DC-filter
[Electronic circuits]
kamelryttarn
June 20, 2019, 11:43:58 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
shrad
June 20, 2019, 08:57:42 AM
post Re: adventures in homemade flyback bobbins.
[Transformer (ferrite core)]
Patrick
June 20, 2019, 04:06:00 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
johnf
June 20, 2019, 03:50:56 AM
post Re: CRT hacking ideas....
[Electronic circuits]
petespaco
June 19, 2019, 11:29:28 PM
post Re: A dynamical arc model v2
[Dual Resonant Solid State Tesla coils]
Uspring
June 19, 2019, 01:40:16 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Mads Barnkob
June 19, 2019, 10:49:45 AM
post Re: A dynamical arc model v2
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
June 19, 2019, 10:43:32 AM
post Re: Light, laser and optics - Link collection
[Light, lasers and optics]
shrad
June 19, 2019, 10:03:54 AM
post Re: How go get single mode optic fiber to work
[Light, lasers and optics]
shrad
June 19, 2019, 10:02:21 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30