Author Topic: Are holes in the heatsink under the IGBT brick baseplate a problem?  (Read 748 times)

Offline Phoenix

  • High Voltage Experimenter
  • **
  • Posts: 70
  • Karma: +1/-0
    • View Profile
Hello

As you may know, it is very hard to find new large heatsinks without any holes. I am trying to find a heatsink for my large DRSSTC with at least 30x30cm dimensions, but all the offers I can find have holes in them.

Is it a big problem if there are for example a few M5 and M6 holes under the baseplates of the IGBTs? I personally do not really think that this is a big issue, because the heat will get spreaded by the highly thermally conductive baseplate, but I would like to hear your thoughts.

And do you know where I could get such a heatsink?

With best regards
Phoenix
« Last Edit: April 30, 2019, 04:10:24 PM by Phoenix »

Offline oneKone

  • High Voltage Engineer
  • ****
  • Posts: 282
  • Karma: +7/-0
    • View Profile
In many of my projects I've used heatsinks with holes in them. I have the same perspective as you, with large devices like igbt bricks there's quite a large surface area to dissipate heat.

The 2 sources that I can think of for heatsinks are rs components (expensive) or depending on where you live a scrapyard or solar company for old house inverters.

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1180
  • Karma: +17/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
I would not worry too much about a few holes underneath a CM300, with a area of about 70 square-centimeter, a M6 hole is properly around 1/280 (guess) of the total area.

You could fill the holes with brass screws and gently and carefully cut them off with a grinder and sand the surface down to be level, this could however ruin the very even surface and make heat transfer even worse.

I got enough heat sinks so that I could sell you a large one, but it is very expensive to ship. I guess its around 70-80 Euro to another country in Europe.
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline Phoenix

  • High Voltage Experimenter
  • **
  • Posts: 70
  • Karma: +1/-0
    • View Profile
Thank you for your replies  :)

I really didn't knew that RS components sells such large heatsinks, but they are quite expensive as you said, oneKone.

My IGBT Bricks are way larger than CM300 Bricks and they have an area of about 182cm² each, so a few small M6 holes shouldn't really be a problem like you said, Mads.

I think I could still close the holes with some metal epoxy (JB Weld). I just need to be careful that nothing protrudes from the hole, because then the baseplate wouldn't make perfect contact. With the epoxy there also would be no need for grinding, because I can simply wipe away the excess before the whole thing cures.

Greetings
Phoenix

Offline Teravolt

  • High Voltage Technician
  • ***
  • Posts: 101
  • Karma: +2/-0
    • View Profile

Offline oneKone

  • High Voltage Engineer
  • ****
  • Posts: 282
  • Karma: +7/-0
    • View Profile
@phoenix

If you haven't mounted the modules yet you could loctite in some M6 grubscrews and fill the smaller void with heatsink paste. Obviously it's not the best solution but it would stop the paste from leaking out (assuming the holes are drilled through) and it might and a tiny bit more thermal transfer?

Offline Bambinz

  • High Voltage Enthusiast
  • *
  • Posts: 34
  • Karma: +1/-1
    • View Profile
Probably some small holes will not be a big problem because the surface of the IGBT is very large compared to the hole area.
The very important things is that the hole do not compromise the planarity of the heatsink, therefore a little countersink can be a good things.

High Voltage Forum


 


* Recent Topics and Posts

post Re: Unusual polarized non-electrolytic energy discharge capacitor
[Capacitor banks]
MRMILSTAR
Today at 05:19:51 AM
post Re: High voltage Christmas ornaments
[Light, lasers and optics]
klugesmith
Today at 04:57:27 AM
post Re: Unusual polarized non-electrolytic energy discharge capacitor
[Capacitor banks]
T3sl4co1l
Today at 04:04:35 AM
post Re: High voltage Christmas ornaments
[Light, lasers and optics]
John123
Today at 03:29:26 AM
post Re: Mineral oil breakdown voltage
[Voltage Multipliers]
klugesmith
Today at 01:14:06 AM
post High voltage Christmas ornaments
[Light, lasers and optics]
klugesmith
Today at 12:03:49 AM
post Small 65Kv X Ray Transformer hosuing build
[Transformer (iron core)]
DashApple
December 14, 2019, 10:52:49 PM
post Re: Mineral oil breakdown voltage
[Voltage Multipliers]
johnf
December 14, 2019, 09:23:27 PM
post Re: Mineral oil breakdown voltage
[Voltage Multipliers]
MRMILSTAR
December 14, 2019, 09:12:47 PM
post Re: Mineral oil breakdown voltage
[Voltage Multipliers]
johnf
December 14, 2019, 09:07:42 PM
post Re: Unusual polarized non-electrolytic energy discharge capacitor
[Capacitor banks]
MRMILSTAR
December 14, 2019, 09:04:49 PM
post Re: Mineral oil breakdown voltage
[Voltage Multipliers]
MRMILSTAR
December 14, 2019, 08:32:36 PM
post Re: Unusual polarized non-electrolytic energy discharge capacitor
[Capacitor banks]
klugesmith
December 14, 2019, 07:01:18 PM
post Re: Mineral oil breakdown voltage
[Voltage Multipliers]
klugesmith
December 14, 2019, 06:21:27 PM
post Mineral oil breakdown voltage
[Voltage Multipliers]
MRMILSTAR
December 14, 2019, 05:00:39 PM
post Re: QCW ramp generator
[Dual Resonant Solid State Tesla coils]
hammertone
December 14, 2019, 03:05:48 PM
post Re: Unusual polarized non-electrolytic energy discharge capacitor
[Capacitor banks]
T3sl4co1l
December 14, 2019, 05:45:54 AM
post Re: Modern go-to switching devices
[Beginners]
T3sl4co1l
December 14, 2019, 05:37:17 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
December 14, 2019, 05:26:41 AM
post Re: Modern go-to switching devices
[Beginners]
klugesmith
December 14, 2019, 04:54:15 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
December 14, 2019, 02:30:40 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
jturnerkc
December 14, 2019, 02:21:19 AM
post Re: Aethra CCD Webcam Teardown - From Back When Streaming Was Expensive!
[Electronic circuits]
John123
December 14, 2019, 02:14:48 AM
post Modern go-to switching devices
[Beginners]
John123
December 14, 2019, 01:54:55 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
December 14, 2019, 01:37:03 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 14, 2019, 12:57:15 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
MRMILSTAR
December 13, 2019, 11:48:12 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 13, 2019, 11:19:27 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
John123
December 13, 2019, 11:00:18 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 13, 2019, 10:50:03 PM
post Re: Unusual polarized non-electrolytic energy discharge capacitor
[Capacitor banks]
MRMILSTAR
December 13, 2019, 10:46:20 PM
post Re: Unusual polarized non-electrolytic energy discharge capacitor
[Capacitor banks]
klugesmith
December 13, 2019, 10:31:03 PM
post Re: Unusual polarized non-electrolytic energy discharge capacitor
[Capacitor banks]
AndreiRS
December 13, 2019, 10:00:04 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
John123
December 13, 2019, 09:08:28 PM
post Unusual polarized non-electrolytic energy discharge capacitor
[Capacitor banks]
MRMILSTAR
December 13, 2019, 09:06:47 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
MRMILSTAR
December 13, 2019, 08:56:27 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 13, 2019, 05:05:55 PM
post Re: How do you keep in contact with forum people...?
[General chatting]
Mads Barnkob
December 13, 2019, 09:31:58 AM
post Re: My first DRSSTC on bricks
[Dual Resonant Solid State Tesla coils]
johnf
December 13, 2019, 07:56:39 AM
post Re: Royer oscillator (ZVS) driven Jacob's ladder, E80 core transformer
[Transformer (ferrite core)]
AndreiRS
December 13, 2019, 03:59:49 AM
post How do you keep in contact with forum people...?
[General chatting]
AndreiRS
December 13, 2019, 03:23:31 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
klugesmith
December 13, 2019, 12:16:53 AM
post Re: My first DRSSTC on bricks
[Dual Resonant Solid State Tesla coils]
Laci
December 12, 2019, 08:35:24 PM
post Re: How To Make a Stencil For Spray Paint With Cheap Hand Tools
[General chatting]
johnf
December 12, 2019, 07:53:35 PM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
December 12, 2019, 02:52:58 PM
post Re: Royer oscillator (ZVS) driven Jacob's ladder, E80 core transformer
[Transformer (ferrite core)]
John123
December 12, 2019, 02:42:19 PM
post Re: Full bridge much "weaker" than half bridge?
[Solid state Tesla coils]
nick
December 12, 2019, 11:17:36 AM
post Re: Royer oscillator (ZVS) driven Jacob's ladder, E80 core transformer
[Transformer (ferrite core)]
davekni
December 12, 2019, 04:51:08 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
davekni
December 12, 2019, 04:26:22 AM
post Re: How To Make a Stencil For Spray Paint With Cheap Hand Tools
[General chatting]
AndreiRS
December 12, 2019, 01:21:35 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30