Author Topic: Are holes in the heatsink under the IGBT brick baseplate a problem?  (Read 736 times)

Offline Phoenix

  • High Voltage Experimenter
  • **
  • Posts: 70
  • Karma: +1/-0
    • View Profile
Hello

As you may know, it is very hard to find new large heatsinks without any holes. I am trying to find a heatsink for my large DRSSTC with at least 30x30cm dimensions, but all the offers I can find have holes in them.

Is it a big problem if there are for example a few M5 and M6 holes under the baseplates of the IGBTs? I personally do not really think that this is a big issue, because the heat will get spreaded by the highly thermally conductive baseplate, but I would like to hear your thoughts.

And do you know where I could get such a heatsink?

With best regards
Phoenix
« Last Edit: April 30, 2019, 04:10:24 PM by Phoenix »

Offline oneKone

  • High Voltage Engineer
  • ****
  • Posts: 282
  • Karma: +7/-0
    • View Profile
In many of my projects I've used heatsinks with holes in them. I have the same perspective as you, with large devices like igbt bricks there's quite a large surface area to dissipate heat.

The 2 sources that I can think of for heatsinks are rs components (expensive) or depending on where you live a scrapyard or solar company for old house inverters.

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1178
  • Karma: +17/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
I would not worry too much about a few holes underneath a CM300, with a area of about 70 square-centimeter, a M6 hole is properly around 1/280 (guess) of the total area.

You could fill the holes with brass screws and gently and carefully cut them off with a grinder and sand the surface down to be level, this could however ruin the very even surface and make heat transfer even worse.

I got enough heat sinks so that I could sell you a large one, but it is very expensive to ship. I guess its around 70-80 Euro to another country in Europe.
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline Phoenix

  • High Voltage Experimenter
  • **
  • Posts: 70
  • Karma: +1/-0
    • View Profile
Thank you for your replies  :)

I really didn't knew that RS components sells such large heatsinks, but they are quite expensive as you said, oneKone.

My IGBT Bricks are way larger than CM300 Bricks and they have an area of about 182cm² each, so a few small M6 holes shouldn't really be a problem like you said, Mads.

I think I could still close the holes with some metal epoxy (JB Weld). I just need to be careful that nothing protrudes from the hole, because then the baseplate wouldn't make perfect contact. With the epoxy there also would be no need for grinding, because I can simply wipe away the excess before the whole thing cures.

Greetings
Phoenix

Offline Teravolt

  • High Voltage Technician
  • ***
  • Posts: 101
  • Karma: +2/-0
    • View Profile

Offline oneKone

  • High Voltage Engineer
  • ****
  • Posts: 282
  • Karma: +7/-0
    • View Profile
@phoenix

If you haven't mounted the modules yet you could loctite in some M6 grubscrews and fill the smaller void with heatsink paste. Obviously it's not the best solution but it would stop the paste from leaking out (assuming the holes are drilled through) and it might and a tiny bit more thermal transfer?

Offline Bambinz

  • High Voltage Enthusiast
  • *
  • Posts: 34
  • Karma: +1/-1
    • View Profile
Probably some small holes will not be a big problem because the surface of the IGBT is very large compared to the hole area.
The very important things is that the hole do not compromise the planarity of the heatsink, therefore a little countersink can be a good things.

High Voltage Forum


 


* Recent Topics and Posts

post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
Mads Barnkob
Today at 10:27:54 AM
post Re: Worlds Weirdest Microwave Oven, From A Weapons Factory - The Husqvarna Cupol
[Transformer (iron core)]
Mads Barnkob
Today at 10:20:17 AM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
Mads Barnkob
Today at 10:16:32 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
Today at 06:04:28 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
davekni
Today at 05:28:54 AM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
davekni
Today at 04:12:29 AM
post Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
December 09, 2019, 10:52:59 PM
post Replacement guide for Windows Media Center
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
MRMILSTAR
December 09, 2019, 08:29:16 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
Uspring
December 09, 2019, 04:23:33 PM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
MRMILSTAR
December 09, 2019, 03:59:02 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 09, 2019, 03:41:42 PM
post Possible use for large inductor (laminated core)
[Transformer (iron core)]
kamelryttarn
December 09, 2019, 09:43:11 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
December 09, 2019, 12:53:57 AM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
davekni
December 08, 2019, 09:57:51 PM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
MRMILSTAR
December 08, 2019, 05:28:09 PM
post Aethra CCD Webcam Teardown - From Back When Streaming Was Expensive!
[Electronic circuits]
Mads Barnkob
December 08, 2019, 01:33:30 PM
post Platter resistance & inductance
[Induction launchers, coil guns and rails guns]
klugesmith
December 08, 2019, 11:41:00 AM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
davekni
December 08, 2019, 06:50:11 AM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
plasma
December 08, 2019, 12:00:00 AM
post CW multiplier resistor string suggestions
[Voltage Multipliers]
MRMILSTAR
December 07, 2019, 11:32:49 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 07, 2019, 09:54:31 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 07, 2019, 09:48:21 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 07, 2019, 08:59:57 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
MRMILSTAR
December 06, 2019, 08:35:29 PM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 06, 2019, 05:19:26 AM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
davekni
December 06, 2019, 03:48:34 AM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
the_anomaly
December 06, 2019, 03:35:39 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
AstRii
December 06, 2019, 01:27:03 AM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 05, 2019, 11:38:59 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
Mads Barnkob
December 05, 2019, 07:33:01 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
sjsimmo
December 05, 2019, 11:09:20 AM
post Cost reduction in consumer electrics
[Electronic circuits]
klugesmith
December 05, 2019, 07:25:20 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 05, 2019, 05:52:11 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 05, 2019, 05:21:07 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 04, 2019, 06:05:11 PM
post Re: Full bridge showing half the voltage
[Beginners]
shrad
December 04, 2019, 02:57:02 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
Uspring
December 04, 2019, 12:40:51 PM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 04, 2019, 11:20:25 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 04, 2019, 08:28:15 AM
post Re: Full bridge showing half the voltage
[Beginners]
klugesmith
December 04, 2019, 07:41:21 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
MRMILSTAR
December 04, 2019, 05:15:49 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 04, 2019, 05:06:39 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 04, 2019, 04:31:16 AM
post Re: Full bridge showing half the voltage
[Beginners]
davekni
December 04, 2019, 04:26:38 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 04, 2019, 04:10:16 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 04, 2019, 12:28:15 AM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 04, 2019, 12:11:32 AM
post Re: HV resistor in oil
[Voltage Multipliers]
johnf
December 03, 2019, 07:58:41 PM
post Re: Driving Nixie-tubes with arduino
[Electronic circuits]
johnf
December 03, 2019, 07:54:08 PM
post Re: Full bridge showing half the voltage
[Beginners]
klugesmith
December 03, 2019, 07:41:00 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30