Author Topic: [Development] Project of an SSTC driver.  (Read 913 times)

Offline Bambinz

  • High Voltage Enthusiast
  • *
  • Posts: 34
  • Karma: +1/-1
    • View Profile
[Development] Project of an SSTC driver.
« on: April 29, 2019, 08:25:46 PM »
Dear all,
I am developing a new SSTC driver to drive my small teslacoil, because the current driver is not very reliable.

The characteristic will be the followings:
   - Half-bridge configuration
   - Feedback on the secondary with an current trasformer.
   - 2x Separated Board: 1 board for the driver and one board for the half bridge
   - Measure of the primary current
   - Measure of the switch frequency
   - Measure of the mosfet temperature
   - UVLO (under voltage protection)
   - Mosfet protection (Gate protection with zener, Drain-Source protection with snubber and TVS)
   - Minimized connection inductance to allow high current switching at high frequency.
   - Microcontroller STM32F103 to acquire the data, enable/disable the driver in the case of fault condition and generate the interrupt signal.
   - Wi-Fi connect with an ESP32 to send all acquired data to an computer software and to receive the Frequency and duty-cycle of the interrupter, in addition in future to stream the music

If you have any suggestion please write me!!!
I have completed the bridge schematic, tomorrow I will post them.

Offline oneKone

  • High Voltage Engineer
  • ****
  • Posts: 282
  • Karma: +7/-0
    • View Profile
Re: [Development] Project of an SSTC driver.
« Reply #1 on: April 30, 2019, 11:05:17 AM »
Sounds like an interesting project. I'm assuming your going to measure the switching frequency from secondary current feedback?

Offline Bambinz

  • High Voltage Enthusiast
  • *
  • Posts: 34
  • Karma: +1/-1
    • View Profile
Re: [Development] Project of an SSTC driver.
« Reply #2 on: April 30, 2019, 12:48:21 PM »
Yes, I will read the switching frequency from the secondary current feedback, that will be also the driving signal for the driver.

In addition, I would try to implement a ZCS (Zero-current-switch) by reading the primary current and then by using a zero zero cross detector to enable the driver only near the zero current. But i think that will be difficult at 1MHz.


Offline Netzpfuscher

  • High Voltage Experimenter
  • **
  • Posts: 89
  • Karma: +4/-0
    • View Profile
Re: [Development] Project of an SSTC driver.
« Reply #3 on: April 30, 2019, 01:04:44 PM »
If you are planning to have a PC application you can take a look at our Teslaterm: https://github.com/Netzpfuscher/Teslaterm/tree/typescript
I also have a ESP32 Interface: https://github.com/Netzpfuscher/UD3_ESP32

Teslaterm is very flexible. It's not specifically designed for UD3. You can send text to the terminal window and use the c library to send telemetry like scope data or data for the gauges. I even have simple graphics functions for sending text/lines/colors from the microcontroller to the terminal screen.



Offline Bambinz

  • High Voltage Enthusiast
  • *
  • Posts: 34
  • Karma: +1/-1
    • View Profile
Re: [Development] Project of an SSTC driver.
« Reply #4 on: April 30, 2019, 06:22:36 PM »
Thank you very much for the indication. The software is fantastic!
I will try to adapt the software with my data.
Eventually, I will rebuild a simplified interface with python :)

Offline Bambinz

  • High Voltage Enthusiast
  • *
  • Posts: 34
  • Karma: +1/-1
    • View Profile
Re: [Development] Project of an SSTC driver.
« Reply #5 on: May 03, 2019, 07:52:19 PM »
This is the schematic of the half-bridge:

Offline Bambinz

  • High Voltage Enthusiast
  • *
  • Posts: 34
  • Karma: +1/-1
    • View Profile
Re: [Development] Project of an SSTC driver.
« Reply #6 on: May 05, 2019, 01:33:37 PM »
I would like to make some changes in the driver.
I have found a 440VA 53VAC transformer that I would like to use for the next teslacoil.

Therefore VDC will be +- 75V (that can reach +-90 without load), therefore I have choosed a mosfet of 250Vds ->  IRFB4229
With a very short and semplified thermal calculation, result that can handle about 55A with the interrupter set to 20Hz and duty-cycle of 5% (Setted as worst case).

I would like to have the same carachteristic of the small coil with an high peak current and a low duty-cycle to have an low mean power and an high pulse power.

Thereticaly the small teslacoil have an peak current of about 30A, with a 24V supply and a push-pull driver will results in a 30A*24V*2= 1440W (peak power) and an average power of 40W. The results is about 7-8cm of spark.

Therefore the average current will be about: 55A * 0.05 = 2.75A with an average power of 75V*2.75 = 206W. And a Peak power of about 75V*55A =4125W

Therefore we will have a 4x power therefore I will expect a sparklength in the range of 30cm. Can be correct?

Offline Bambinz

  • High Voltage Enthusiast
  • *
  • Posts: 34
  • Karma: +1/-1
    • View Profile
Re: [Development] Project of an SSTC driver.
« Reply #7 on: August 08, 2019, 11:56:51 AM »
I have just ordered the board from PCBWay for the driver. I hope that all works good xD
In the next day I will post the complete schematic :)

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1179
  • Karma: +17/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: [Development] Project of an SSTC driver.
« Reply #8 on: August 16, 2019, 10:07:31 PM »
I would like to make some changes in the driver.
I have found a 440VA 53VAC transformer that I would like to use for the next teslacoil.

Therefore VDC will be +- 75V (that can reach +-90 without load), therefore I have choosed a mosfet of 250Vds ->  IRFB4229
With a very short and semplified thermal calculation, result that can handle about 55A with the interrupter set to 20Hz and duty-cycle of 5% (Setted as worst case).

I would like to have the same carachteristic of the small coil with an high peak current and a low duty-cycle to have an low mean power and an high pulse power.

Thereticaly the small teslacoil have an peak current of about 30A, with a 24V supply and a push-pull driver will results in a 30A*24V*2= 1440W (peak power) and an average power of 40W. The results is about 7-8cm of spark.

Therefore the average current will be about: 55A * 0.05 = 2.75A with an average power of 75V*2.75 = 206W. And a Peak power of about 75V*55A =4125W

Therefore we will have a 4x power therefore I will expect a sparklength in the range of 30cm. Can be correct?

Spark length estimation for SSTC was never really linear in my experiments, it felt more like that I could just keep adding topload capacitance to get longer arcs :)
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

High Voltage Forum

Re: [Development] Project of an SSTC driver.
« Reply #8 on: August 16, 2019, 10:07:31 PM »

 


* Recent Topics and Posts

post Re: Royer oscillator (ZVS) driven Jacob's ladder, E80 core transformer
[Transformer (ferrite core)]
AndreiRS
Today at 03:59:49 AM
post How do you keep in contact with forum people...?
[General chatting]
AndreiRS
Today at 03:23:31 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
klugesmith
Today at 12:16:53 AM
post Re: My first DRSSTC on bricks
[Dual Resonant Solid State Tesla coils]
Laci
December 12, 2019, 08:35:24 PM
post Re: How To Make a Stencil For Spray Paint With Cheap Hand Tools
[General chatting]
johnf
December 12, 2019, 07:53:35 PM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
December 12, 2019, 02:52:58 PM
post Re: Royer oscillator (ZVS) driven Jacob's ladder, E80 core transformer
[Transformer (ferrite core)]
John123
December 12, 2019, 02:42:19 PM
post Re: Full bridge much "weaker" than half bridge?
[Solid state Tesla coils]
nick
December 12, 2019, 11:17:36 AM
post Re: Royer oscillator (ZVS) driven Jacob's ladder, E80 core transformer
[Transformer (ferrite core)]
davekni
December 12, 2019, 04:51:08 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
davekni
December 12, 2019, 04:26:22 AM
post Re: How To Make a Stencil For Spray Paint With Cheap Hand Tools
[General chatting]
AndreiRS
December 12, 2019, 01:21:35 AM
post Re: Using same winding on separate rails?
[Transformer (iron core)]
Twospoons
December 11, 2019, 10:49:04 PM
post Re: A dynamical arc model v2
[Dual Resonant Solid State Tesla coils]
Uspring
December 11, 2019, 05:28:46 PM
post Re: Full bridge much "weaker" than half bridge?
[Solid state Tesla coils]
Fumeaux
December 11, 2019, 03:11:42 PM
post Re: Royer oscillator (ZVS) driven Jacob's ladder, E80 core transformer
[Transformer (ferrite core)]
John123
December 11, 2019, 02:22:10 PM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
December 11, 2019, 02:09:19 PM
post Full bridge much "weaker" than half bridge?
[Solid state Tesla coils]
nick
December 11, 2019, 01:10:57 PM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
kamelryttarn
December 11, 2019, 08:48:36 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
December 11, 2019, 06:08:48 AM
post Re: SSTC low voltage at gate transformer and heating drivers
[Solid state Tesla coils]
davekni
December 11, 2019, 05:38:17 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
davekni
December 11, 2019, 05:01:31 AM
post Re: Using same winding on separate rails?
[Transformer (iron core)]
John123
December 11, 2019, 01:52:43 AM
post Re: Using same winding on separate rails?
[Transformer (iron core)]
klugesmith
December 11, 2019, 01:41:04 AM
post Re: Worlds Weirdest Microwave Oven, From A Weapons Factory - The Husqvarna Cupol
[Transformer (iron core)]
klugesmith
December 11, 2019, 01:37:13 AM
post Re: Using same winding on separate rails?
[Transformer (iron core)]
John123
December 11, 2019, 01:19:58 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 11, 2019, 01:14:32 AM
post Re: Using same winding on separate rails?
[Transformer (iron core)]
klugesmith
December 11, 2019, 01:04:08 AM
post Re: SSTC low voltage at gate transformer and heating drivers
[Solid state Tesla coils]
babass
December 10, 2019, 11:24:50 PM
post Using same winding on separate rails?
[Transformer (iron core)]
John123
December 10, 2019, 10:52:50 PM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
December 10, 2019, 03:35:40 PM
post Re: Why did 4HV die??
[General chatting]
John123
December 10, 2019, 03:21:07 PM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
Mads Barnkob
December 10, 2019, 03:04:28 PM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
December 10, 2019, 02:57:45 PM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
kamelryttarn
December 10, 2019, 11:23:48 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
Mads Barnkob
December 10, 2019, 10:27:54 AM
post Re: Worlds Weirdest Microwave Oven, From A Weapons Factory - The Husqvarna Cupol
[Transformer (iron core)]
Mads Barnkob
December 10, 2019, 10:20:17 AM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
Mads Barnkob
December 10, 2019, 10:16:32 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
December 10, 2019, 06:04:28 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
davekni
December 10, 2019, 05:28:54 AM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
davekni
December 10, 2019, 04:12:29 AM
post Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
December 09, 2019, 10:52:59 PM
post Replacement guide for Windows Media Center
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
MRMILSTAR
December 09, 2019, 08:29:16 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
Uspring
December 09, 2019, 04:23:33 PM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
MRMILSTAR
December 09, 2019, 03:59:02 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 09, 2019, 03:41:42 PM
post Possible use for large inductor (laminated core)
[Transformer (iron core)]
kamelryttarn
December 09, 2019, 09:43:11 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
December 09, 2019, 12:53:57 AM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
davekni
December 08, 2019, 09:57:51 PM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
MRMILSTAR
December 08, 2019, 05:28:09 PM
post Aethra CCD Webcam Teardown - From Back When Streaming Was Expensive!
[Electronic circuits]
Mads Barnkob
December 08, 2019, 01:33:30 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30