Author Topic: Phoenix's Large DRSSTC II  (Read 956 times)

Offline Phoenix

  • High Voltage Experimenter
  • **
  • Posts: 64
  • Karma: +1/-0
    • View Profile
Phoenix's Large DRSSTC II
« on: April 08, 2019, 01:12:14 PM »
Hello everyone  :)

About one year ago, I have finished my 160mm DRSSTC. Now, i am planning a 315mm DRSSTC. I have already ordered 6 large GTO Snubbers with 6µF and 3200V DC. I will put them in series to get 19200V DC @1µF. The capacitors can handle up to 2200A peak and 100 A RMS. Here is the ebay link: https://www.ebay.at/itm/Electronicon-6uF-660Vac-3200V-DC-1050V-AC-Cylindrical-Film-Capacitor/362555302076?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649

I got them for 35€ each, which is not too bad.

Here are my JAVA TC calculations: 


Secondary Diameter: 315mm
Wire diameter: 0.8mm
1800 Turns
158cm winding length

Primary inner diameter: 385mm
outer diameter: 865mm
15mm Copper tube
15mm turn spacing
8 turns in total
tapped at around 4.8 Turns including spark loading

Topload:
40cm Aluflextube
150cm diameter

I am planning on using a fullbridge made out of cm600du-24nf Igbts. The coil is going to run on a DIY 3 Phase variac that can deliver up to 30kW for one minute. This will give me up to 660V DC Bus voltage. What do you think about this specs?

Here is another question: Is there a big difference in terms of performance between DC Link and electrolytic capacitors? I know that you need less dc bus energy if you use dc link capacitors. How much less energy do i need?

Greetings
Phoenix 
« Last Edit: April 08, 2019, 04:06:11 PM by Phoenix »

Online Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1117
  • Karma: +17/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Phoenix's Large DRSSTC II
« Reply #1 on: April 23, 2019, 09:39:04 PM »
Get ready for the ride of your life, a big coil is just a whole other game, the sound, the weight, the noise, the sparks, everything is just mindblowing.

All your specs looks fine, well specified and thoughtfully planned.

I ran my large DRSSTC on a 3 phase stack of mere 10A variacs and pulling 15kW through those did not make them heat up one bit, tough little transformers :)

I am not sure about the capacitance ratio when comparing electrolytics and dc link capacitors, but maybe you can get an idea from looking at the dV/dt times and ESR to see how much faster it can deliver some peak current.

Looking forward to see this monster :)
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline Phoenix

  • High Voltage Experimenter
  • **
  • Posts: 64
  • Karma: +1/-0
    • View Profile
Re: Phoenix's Large DRSSTC II
« Reply #2 on: April 25, 2019, 11:14:32 AM »
Hello Mads

Thank you for your advice  :)

I have found a good ebay offer on new 10000µF 350V electrolytic capacitors, so I bought 6 of them to get 700V @ 15000µF for the inverter. This gives me around 3600 Joules, which is more than enough.

I also found a good offer for large IGBT Bricks, so I bought 4× FZ800R12KF4 from Eupec/Infineon. These Bricks are not based on the newest technologies, but i believe they are still suitable. According to my calculations, they should easily handle up to 3000A. I really like that these Bricks only have 55nF gate capacitance, which is really low for a 800A IGBT. This low capacitance enables me to use a GDT instead of a direct drive IC. Here you can download the data sheet: https://www.mouser.at/datasheet/2/196/fz800r12kf4-93487.pdf

Here you can see the electrolytic capacitors and the GTO Snubber Caps:


Here you can see the MMC. I will try to get more of these caps to increase my RMS and Peak current capability. Right now, i am limited to 2200A, because of the maximum peak current of the capacitors.


I have got another question about the RMS current capability of these large GTO snubber capacitors. According to the datasheet value, they can handle 100A RMS. But according to my own hotspot temperature calculations, they should be able to handle around 180A RMS. I think the capacitors are only rated as 100A because of the terminals. I saw on your website that the capacitors in your large DRSSTC III are rated for 80A RMS. Did you run into any heating issues because of that?

Have you seen my comment about the IGBT calculations on your website? I think I found a mistake there, but I am not sure.

Greetings
Phoenix

 
« Last Edit: April 25, 2019, 11:42:37 AM by Phoenix »

Offline Phoenix

  • High Voltage Experimenter
  • **
  • Posts: 64
  • Karma: +1/-0
    • View Profile
Re: Phoenix's Large DRSSTC II
« Reply #3 on: April 29, 2019, 08:21:26 PM »
The IGBT Bricks have finally arrived and they are way bigger then expected ;D

The SKM200 looks tiny next to them:



They are the same size like the CM600DU24NF Halfbridge Brick, but I need 4 of them, because this are single IGBTs.

Online Laci

  • High Voltage Engineer
  • ****
  • Posts: 209
  • Karma: +6/-0
    • View Profile
Re: Phoenix's Large DRSSTC II
« Reply #4 on: April 29, 2019, 08:42:52 PM »
...and I thought my SKM400s are huge...
I wonder how big your heatsink will be too. :D

Good luck for the building and looking forward to steal some techniques.  ;)

Offline Bambinz

  • High Voltage Enthusiast
  • *
  • Posts: 34
  • Karma: +1/-1
    • View Profile
Re: Phoenix's Large DRSSTC II
« Reply #5 on: April 29, 2019, 08:50:58 PM »
This is an awesome project.
I'am an electronic Engineer but I haven't the competence to develop an so high power device.
You are crazy xD please pay attention because a failure will results in a new years show xD

Offline Phoenix

  • High Voltage Experimenter
  • **
  • Posts: 64
  • Karma: +1/-0
    • View Profile
Re: Phoenix's Large DRSSTC II
« Reply #6 on: April 29, 2019, 09:05:38 PM »
Hello Laci and Bambinz

Thank you for your compliments and the nice replies  :)

@Laci

I have yet to find a heatsink that large, but there are quite frequent ebay offers for such heatsinks.

I think you can't steal techniques from me, i have seen your thread and you definitely know how to build a DRSSTC  :)

@Bambinz

It really means a lot to me to hear something like that from an electronic Engineer   :D

I know the components may look intemidating, but it really isn't more difficult to build a large DRSSTC than a medium DRSSTC. Everything just needs to get scaled up, the basic working principle stays the same. But as you already said, you have to be way more careful with a large DRSSTC. The arcs could strike further than you might expect and a crash of the fullbridge could cause a lot of shrapnell to fly around. 3600 Joules is definitely more than enough to really blow something up.

Greetings
Phoenix

Offline Bambinz

  • High Voltage Enthusiast
  • *
  • Posts: 34
  • Karma: +1/-1
    • View Profile
Re: Phoenix's Large DRSSTC II
« Reply #7 on: April 30, 2019, 06:34:07 PM »
It is a very difficult project also for an Engineer, because handle an so high current/voltage is not obvious. Theoreticaly, probably, is not very complex but in practise there are many things to take care: Layout, Power dissipation, ...
Requires many experience in the field, I think that you have certainly build many DRSSTC in various size.

To reduce the thermal resistance, I know that in generaly, the heatsink is polished to have a perfect planarity to increas the contact area. In addition, you should respect the mounting torque to have the best possible contact.  ;D

Offline Phoenix

  • High Voltage Experimenter
  • **
  • Posts: 64
  • Karma: +1/-0
    • View Profile
Re: Phoenix's Large DRSSTC II
« Reply #8 on: May 01, 2019, 08:31:05 PM »
Yes, you are right, there are quite a lot of things to consider when building a DRSSTC. You need to keep the stray inductance of your bus layout low, you have to make sure that no components get overloaded via calculations, you need to take care when winding the secondary to avoid flashovers, you need to keep the distance from the primary coil to the secondary coil high enough to prevent flashovers between them, ....

Here you can see the primary coil I designed with a computer software called "Geogebra". The red lines are the primary supports and by measuring the points via the software where the spiral crosses them, I get the distance and I know where to drill without any annoying calculations and possible mistakes. The x and y scales are in mm.



Greetings
Phoenix


Offline Bambinz

  • High Voltage Enthusiast
  • *
  • Posts: 34
  • Karma: +1/-1
    • View Profile
Re: Phoenix's Large DRSSTC II
« Reply #9 on: May 03, 2019, 07:45:13 PM »
Very good!
Geogebra is a good software. I have used it during the Bachelor for the mathematics and physics :)

Why in the big teslacoil is used almost always a flat spiral for the primary?  To maximixing the distance between the primary and the secondary and to not have a too high coupling?

Online Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1117
  • Karma: +17/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Phoenix's Large DRSSTC II
« Reply #10 on: May 03, 2019, 10:26:23 PM »
I have got another question about the RMS current capability of these large GTO snubber capacitors. According to the datasheet value, they can handle 100A RMS. But according to my own hotspot temperature calculations, they should be able to handle around 180A RMS. I think the capacitors are only rated as 100A because of the terminals. I saw on your website that the capacitors in your large DRSSTC III are rated for 80A RMS. Did you run into any heating issues because of that?

Have you seen my comment about the IGBT calculations on your website? I think I found a mistake there, but I am not sure.

Greetings
Phoenix

I assumed their RMS rating to be 80A compared to similar sized GTO snubber capacitors where the value was given in the datasheet. It is properly higher as they have rather large terminals.

GTO capacitors large physical size and if they are connected to heavy copper busbar will help them dissipate the losses fast and thus the dooms day prophecies of my MMC calculator wont come true, as it predicts I run them at 195 degree Celsius temperature rise :)

I saw your comment the day you wrote it, thought about it, looked at my calculations and had to check my spreadsheets on the PC to find out why I did as I wrote. I have concluded that the shown graph certainly isn't from the CM600. So I updated the article with a note about it being an example and that the 0.081 used for the CM600 is the thermal impedance multiplied with the single pulse normalized transient given in the datasheet, at 0.02 duty cycle that corresponds to 1, so I left that out in 2015, but added that now as there might be other cases where duty cycle is lower or higher.

So it was just a worst case scenario that apparently aligned up with a number from the example by coincidence. 
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

High Voltage Forum

Re: Phoenix's Large DRSSTC II
« Reply #10 on: May 03, 2019, 10:26:23 PM »

 


* Recent Topics and Posts

post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
Today at 05:43:13 PM
post Re: Help choosing a Hantek USB oscilloscope
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Twospoons
Today at 01:32:30 PM
post Re: Adventures in induction heating
[Electronic circuits]
Coyote
Today at 10:56:19 AM
post Re: Help choosing a Hantek USB oscilloscope
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
kamelryttarn
Today at 10:02:28 AM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
davekni
Today at 07:05:19 AM
post Re: Help choosing a Hantek USB oscilloscope
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Hydron
September 19, 2019, 11:16:21 PM
post Re: The new toy
[Laboratories ]
AlexanderHun
September 19, 2019, 09:49:30 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
September 19, 2019, 09:49:15 PM
post Re: The new toy
[Laboratories ]
Mads Barnkob
September 19, 2019, 09:13:29 PM
post Re: Help choosing a Hantek USB oscilloscope
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Mads Barnkob
September 19, 2019, 09:08:20 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
September 19, 2019, 07:16:20 PM
post Help choosing a Hantek USB oscilloscope
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
kamelryttarn
September 19, 2019, 04:19:58 PM
post The new toy
[Laboratories ]
AlexanderHun
September 19, 2019, 09:01:46 AM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
September 18, 2019, 07:27:46 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
September 18, 2019, 06:56:20 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
September 18, 2019, 05:08:06 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
September 18, 2019, 01:35:58 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
September 18, 2019, 05:54:23 AM
post Re: Blast from the past!
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
klugesmith
September 18, 2019, 05:05:55 AM
post Re: UD2.7 Gate Signals
[Dual Resonant Solid State Tesla coils]
coilinator
September 17, 2019, 08:24:59 PM
post Re: Blast from the past!
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
MRMILSTAR
September 17, 2019, 08:19:45 PM
post Re: Blast from the past!
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Mads Barnkob
September 17, 2019, 06:53:52 PM
post Blast from the past!
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
MRMILSTAR
September 17, 2019, 05:52:00 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
September 17, 2019, 05:00:47 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
davekni
September 17, 2019, 06:48:38 AM
post Re: My second DRSSTC
[Dual Resonant Solid State Tesla coils]
erdal
September 16, 2019, 11:07:27 PM
post Re: 750W solar offgrid 24V/150Ah battery setup with Victron charger
[Electronic circuits]
johnf
September 16, 2019, 09:48:37 PM
post Re: adventures in homemade flyback bobbins.
[Transformer (ferrite core)]
AlexanderHun
September 16, 2019, 10:42:44 AM
post Re: Offgrid 48V solar to 24V battery setup
[Electronic circuits]
Mads Barnkob
September 16, 2019, 09:40:27 AM
post Re: My second DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
September 16, 2019, 09:28:43 AM
post Re: Large Ferrite Core with IGBT-Brick Driver
[Transformer (ferrite core)]
Mads Barnkob
September 16, 2019, 09:24:17 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
T3sl4co1l
September 16, 2019, 06:59:12 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
davekni
September 16, 2019, 04:18:26 AM
post Re: My second DRSSTC
[Dual Resonant Solid State Tesla coils]
davekni
September 16, 2019, 02:49:28 AM
post Re: Large Ferrite Core with IGBT-Brick Driver
[Transformer (ferrite core)]
davekni
September 16, 2019, 02:43:18 AM
post Re: Homemade HV transformer
[Transformer (ferrite core)]
davekni
September 16, 2019, 02:36:17 AM
post Re: adventures in homemade flyback bobbins.
[Transformer (ferrite core)]
davekni
September 16, 2019, 02:26:40 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
September 16, 2019, 01:50:19 AM
post Re: UD2.7 Gate Signals
[Dual Resonant Solid State Tesla coils]
coilinator
September 15, 2019, 08:22:47 PM
post Re: My second DRSSTC
[Dual Resonant Solid State Tesla coils]
erdal
September 15, 2019, 02:09:17 PM
post Re: Homemade HV transformer
[Transformer (ferrite core)]
AlexanderHun
September 15, 2019, 10:39:29 AM
post Re: Homemade HV transformer
[Transformer (ferrite core)]
ElectroXa
September 14, 2019, 07:01:28 PM
post Re: adventures in homemade flyback bobbins.
[Transformer (ferrite core)]
AlexanderHun
September 14, 2019, 06:59:13 PM
post Re: Homemade HV transformer
[Transformer (ferrite core)]
AlexanderHun
September 14, 2019, 06:43:15 PM
post Re: Homemade HV transformer
[Transformer (ferrite core)]
ritaismyconscience
September 14, 2019, 06:35:32 PM
post Homemade HV transformer
[Transformer (ferrite core)]
AlexanderHun
September 14, 2019, 05:05:00 PM
post Re: UD2.7 Gate Signals
[Dual Resonant Solid State Tesla coils]
profdc9
September 14, 2019, 04:50:10 PM
post Re: UD2.7 Gate Signals
[Dual Resonant Solid State Tesla coils]
coilinator
September 14, 2019, 08:42:55 AM
post Re: Transistors good for DRSSTC?
[Dual Resonant Solid State Tesla coils]
ritaismyconscience
September 13, 2019, 05:50:53 AM
post Re: Transistors good for DRSSTC?
[Dual Resonant Solid State Tesla coils]
Max
September 12, 2019, 12:47:03 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30