Author Topic: Car starter on PWM  (Read 637 times)

Offline AndreiRS

  • High Voltage Experimenter
  • **
  • Posts: 73
  • Karma: +0/-0
    • View Profile
Car starter on PWM
« on: April 06, 2019, 02:59:17 AM »
Hi all. Oooof I have been away for a while. Not really doing much on electronics or HV, just renovating the house and working a bit. I also had to put my TC on the shelf because capacitors are not available here for a decent price. Then I got back to building a diy jet engine lol. But I did a project on electronics and today I remembered I should share it. ;D

So I got a normal PWM circuit, like the one you would get on ebay, it uses a LM324 as signal generator. 555 generators used to burn mosfets for some reason. Then I just removed the IRF540 from PWM board and put a mosfet push-pull driver there. Just a NPN and PNP transistors in series.



But instead of 1 mosfet, I used 4 IRF3205 in parallel, which should be capable of 110A each. And I think one 10ohm resistor on each gate. Yeah they will probably explode a lot earlier before those 110 amps hahah. But they are doing good till now. I started using 3600Hz as calculated using some "motor constant", it didn't work well. Latter I lowered it to 500Hz to have more torque available.

I'm kinda quiet here on the forum, I just don't have anything good to post and I don't know a thing about SSTCs. I will read other people post, maybe I can help someone a bit.

The plan is to use this on a electric bike. I just don't like "torqueless" brushless DC motors. Brushed motors from car engine starters are way more crazy haha. I had to remove all the front part of the car starter. Then I bought another rear end cover from the same model and used it as front cover too. Video is in portuguese but I said there about the same I said here. The 2.5mm² wires got warm with this small test. But it was just a test. I will use 10mm² wires.

« Last Edit: April 06, 2019, 03:06:44 AM by AndreiRS »

Offline T3sl4co1l

  • High Voltage Experimenter
  • **
  • Posts: 91
  • Karma: +8/-0
    • View Profile
Re: Car starter on PWM
« Reply #1 on: April 06, 2019, 09:04:32 AM »
No catch diodes across the motor? :o

Tim

Offline AndreiRS

  • High Voltage Experimenter
  • **
  • Posts: 73
  • Karma: +0/-0
    • View Profile
Re: Car starter on PWM
« Reply #2 on: April 06, 2019, 03:43:45 PM »
I have a MUR1620 in parallel, but it is at the connector part. ::)

Offline petespaco

  • High Voltage Technician
  • ***
  • Posts: 130
  • Karma: +8/-0
    • View Profile
    • French Creek Valley Activities
Re: Car starter on PWM
« Reply #3 on: April 06, 2019, 04:22:50 PM »
I didn't think that car starters were rated for continuous duty.  is this one different?

Offline AndreiRS

  • High Voltage Experimenter
  • **
  • Posts: 73
  • Karma: +0/-0
    • View Profile
Re: Car starter on PWM
« Reply #4 on: April 06, 2019, 05:47:37 PM »
It is just like all others. But I will "drop" it inside a small radiator fluid tank. I have seen some people do that, it works. Then the sprocket will come out from the top.

High Voltage Forum

Re: Car starter on PWM
« Reply #4 on: April 06, 2019, 05:47:37 PM »

 


* Recent Topics and Posts

post Re: Unusual polarized non-electrolytic energy discharge capacitor
[Capacitor banks]
MRMILSTAR
Today at 05:19:51 AM
post Re: High voltage Christmas ornaments
[Light, lasers and optics]
klugesmith
Today at 04:57:27 AM
post Re: Unusual polarized non-electrolytic energy discharge capacitor
[Capacitor banks]
T3sl4co1l
Today at 04:04:35 AM
post Re: High voltage Christmas ornaments
[Light, lasers and optics]
John123
Today at 03:29:26 AM
post Re: Mineral oil breakdown voltage
[Voltage Multipliers]
klugesmith
Today at 01:14:06 AM
post High voltage Christmas ornaments
[Light, lasers and optics]
klugesmith
Today at 12:03:49 AM
post Small 65Kv X Ray Transformer hosuing build
[Transformer (iron core)]
DashApple
December 14, 2019, 10:52:49 PM
post Re: Mineral oil breakdown voltage
[Voltage Multipliers]
johnf
December 14, 2019, 09:23:27 PM
post Re: Mineral oil breakdown voltage
[Voltage Multipliers]
MRMILSTAR
December 14, 2019, 09:12:47 PM
post Re: Mineral oil breakdown voltage
[Voltage Multipliers]
johnf
December 14, 2019, 09:07:42 PM
post Re: Unusual polarized non-electrolytic energy discharge capacitor
[Capacitor banks]
MRMILSTAR
December 14, 2019, 09:04:49 PM
post Re: Mineral oil breakdown voltage
[Voltage Multipliers]
MRMILSTAR
December 14, 2019, 08:32:36 PM
post Re: Unusual polarized non-electrolytic energy discharge capacitor
[Capacitor banks]
klugesmith
December 14, 2019, 07:01:18 PM
post Re: Mineral oil breakdown voltage
[Voltage Multipliers]
klugesmith
December 14, 2019, 06:21:27 PM
post Mineral oil breakdown voltage
[Voltage Multipliers]
MRMILSTAR
December 14, 2019, 05:00:39 PM
post Re: QCW ramp generator
[Dual Resonant Solid State Tesla coils]
hammertone
December 14, 2019, 03:05:48 PM
post Re: Unusual polarized non-electrolytic energy discharge capacitor
[Capacitor banks]
T3sl4co1l
December 14, 2019, 05:45:54 AM
post Re: Modern go-to switching devices
[Beginners]
T3sl4co1l
December 14, 2019, 05:37:17 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
December 14, 2019, 05:26:41 AM
post Re: Modern go-to switching devices
[Beginners]
klugesmith
December 14, 2019, 04:54:15 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
December 14, 2019, 02:30:40 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
jturnerkc
December 14, 2019, 02:21:19 AM
post Re: Aethra CCD Webcam Teardown - From Back When Streaming Was Expensive!
[Electronic circuits]
John123
December 14, 2019, 02:14:48 AM
post Modern go-to switching devices
[Beginners]
John123
December 14, 2019, 01:54:55 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
December 14, 2019, 01:37:03 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 14, 2019, 12:57:15 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
MRMILSTAR
December 13, 2019, 11:48:12 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 13, 2019, 11:19:27 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
John123
December 13, 2019, 11:00:18 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 13, 2019, 10:50:03 PM
post Re: Unusual polarized non-electrolytic energy discharge capacitor
[Capacitor banks]
MRMILSTAR
December 13, 2019, 10:46:20 PM
post Re: Unusual polarized non-electrolytic energy discharge capacitor
[Capacitor banks]
klugesmith
December 13, 2019, 10:31:03 PM
post Re: Unusual polarized non-electrolytic energy discharge capacitor
[Capacitor banks]
AndreiRS
December 13, 2019, 10:00:04 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
John123
December 13, 2019, 09:08:28 PM
post Unusual polarized non-electrolytic energy discharge capacitor
[Capacitor banks]
MRMILSTAR
December 13, 2019, 09:06:47 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
MRMILSTAR
December 13, 2019, 08:56:27 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 13, 2019, 05:05:55 PM
post Re: How do you keep in contact with forum people...?
[General chatting]
Mads Barnkob
December 13, 2019, 09:31:58 AM
post Re: My first DRSSTC on bricks
[Dual Resonant Solid State Tesla coils]
johnf
December 13, 2019, 07:56:39 AM
post Re: Royer oscillator (ZVS) driven Jacob's ladder, E80 core transformer
[Transformer (ferrite core)]
AndreiRS
December 13, 2019, 03:59:49 AM
post How do you keep in contact with forum people...?
[General chatting]
AndreiRS
December 13, 2019, 03:23:31 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
klugesmith
December 13, 2019, 12:16:53 AM
post Re: My first DRSSTC on bricks
[Dual Resonant Solid State Tesla coils]
Laci
December 12, 2019, 08:35:24 PM
post Re: How To Make a Stencil For Spray Paint With Cheap Hand Tools
[General chatting]
johnf
December 12, 2019, 07:53:35 PM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
December 12, 2019, 02:52:58 PM
post Re: Royer oscillator (ZVS) driven Jacob's ladder, E80 core transformer
[Transformer (ferrite core)]
John123
December 12, 2019, 02:42:19 PM
post Re: Full bridge much "weaker" than half bridge?
[Solid state Tesla coils]
nick
December 12, 2019, 11:17:36 AM
post Re: Royer oscillator (ZVS) driven Jacob's ladder, E80 core transformer
[Transformer (ferrite core)]
davekni
December 12, 2019, 04:51:08 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
davekni
December 12, 2019, 04:26:22 AM
post Re: How To Make a Stencil For Spray Paint With Cheap Hand Tools
[General chatting]
AndreiRS
December 12, 2019, 01:21:35 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30