Author Topic: about drsstc interrupter connection  (Read 425 times)

Offline Ect1453

  • High Voltage Enthusiast
  • *
  • Posts: 2
  • Karma: +0/-0
    • View Profile
about drsstc interrupter connection
« on: December 28, 2018, 02:50:31 PM »
Hey, guys, I need a suggestion. you know we use fiber optic transceiver to connect an intruperter to drsstc. what else does he use?  Anybody try Optocoupler?. or do you have any other suggestions ?

Offline sjsimmo

  • High Voltage Enthusiast
  • *
  • Posts: 34
  • Karma: +3/-0
  • Australia
    • View Profile
Re: about drsstc interrupter connection
« Reply #1 on: December 29, 2018, 02:20:47 AM »

Hi Ect1453, :)

Some people just use shielded RCA cable, or similar. Of course this doesn't give the same amount of isolation as Fibre Optic though.

On my first SSTC I used an optocoupler at the SSTC end, and shielded RCA cable to the interrupter. This works, but probably shouldn't be used at the high power levels of a DRSSTC, unless using a simple 555 interrupter (or similar micro-controller/midi/laptop free design).
When testing my SSTC, I did notice some noise making it into the interrupter circuit. This may be prevented by another optocoupler at the interrupter end of the RCA cable, but I'm not entirely sure.
« Last Edit: December 29, 2018, 02:27:25 AM by sjsimmo »
I like my food cooked with lightning.

Offline Mads Barnkob

  • Administrator
  • High Voltage Senior
  • *****
  • Posts: 990
  • Karma: +15/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: about drsstc interrupter connection
« Reply #2 on: December 29, 2018, 12:55:50 PM »
I have also used shielded mini-jack for audio input to a SSTC and it only gave me problems. I spend more time shielding it than building a isolated interface would have. I did also make a mistake by having the audio interrupter in the enclosure under the coil. But the noise issue was more the audio source that would halt, reboot and lock up when I turned up the voltage to the cool too much.

I only make coils with fiber connected interrupters now, for less noise problems and human safety :)
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline Ect1453

  • High Voltage Enthusiast
  • *
  • Posts: 2
  • Karma: +0/-0
    • View Profile
Re: about drsstc interrupter connection
« Reply #3 on: December 30, 2018, 06:46:26 AM »
The BNC connector for the drsstc cutter produced in China also added output. it makes sense to me.   what kind of solution Do you think BNC would have?

Offline Mads Barnkob

  • Administrator
  • High Voltage Senior
  • *****
  • Posts: 990
  • Karma: +15/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: about drsstc interrupter connection
« Reply #4 on: January 03, 2019, 11:54:34 AM »
With BNC you will have some good standard parts that is well shielded, but constructed for 50/75 Ohm impedance.

The biggest problem with direct cabling is not shielding it, but that the shield conducts noise from the coil to the interrupter/keyboard/whatever you are sending the signal from.
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

High Voltage Forum

Re: about drsstc interrupter connection
« Reply #4 on: January 03, 2019, 11:54:34 AM »

 


* Recent Topics and Posts

post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
hightemp1
Today at 05:51:09 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
Today at 04:07:17 AM
post Strange GDT signals (need to help)
[Dual Resonant Solid State Tesla coils]
VNTC
Today at 02:19:24 AM
post Re: Easy access to optimal resonance frequency but the benefit is quite small
[Dual Resonant Solid State Tesla coils]
VNTC
Today at 02:00:48 AM
post Re: Strange gdt waveforms
[Dual Resonant Solid State Tesla coils]
VNTC
Today at 01:33:56 AM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
May 22, 2019, 08:31:55 PM
post Re: Easy access to optimal resonance frequency but the benefit is quite small
[Dual Resonant Solid State Tesla coils]
dexter
May 22, 2019, 08:31:51 PM
post Easy access to optimal resonance frequency but the benefit is quite small
[Dual Resonant Solid State Tesla coils]
VNTC
May 21, 2019, 11:35:57 PM
post Re: Offgrid 48V solar to 24V battery setup
[Electronic circuits]
Mads Barnkob
May 21, 2019, 09:59:54 PM
post Re: General Oscilloscope Probing Techniques for (DR)SSTC h-bridge
[Beginners]
Mads Barnkob
May 21, 2019, 09:51:27 PM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
T3sl4co1l
May 21, 2019, 09:49:03 PM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
82026
May 21, 2019, 09:02:10 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Vaclav
May 21, 2019, 08:59:57 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
May 21, 2019, 08:28:43 PM
post Re: Identification of unknown embedded computer, help needed.
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Mads Barnkob
May 21, 2019, 08:22:28 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Vaclav
May 21, 2019, 06:21:37 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
May 21, 2019, 06:12:55 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
profdc9
May 21, 2019, 04:06:38 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Vaclav
May 21, 2019, 03:56:56 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Vaclav
May 21, 2019, 03:46:56 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
profdc9
May 21, 2019, 02:32:59 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
May 21, 2019, 06:12:18 AM
post Re: Offgrid 48V solar to 24V battery setup
[Electronic circuits]
profdc9
May 20, 2019, 11:30:34 PM
post DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Vaclav
May 20, 2019, 06:38:54 PM
post Re: General Oscilloscope Probing Techniques for (DR)SSTC h-bridge
[Beginners]
Teravolt
May 20, 2019, 06:33:49 PM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
82026
May 20, 2019, 02:27:59 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
hightemp1
May 20, 2019, 02:57:46 AM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
T3sl4co1l
May 20, 2019, 01:06:27 AM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
82026
May 19, 2019, 09:14:59 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
May 19, 2019, 06:40:41 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
flyrod
May 19, 2019, 04:04:12 PM
post Re: Offgrid 48V solar to 24V battery setup
[Electronic circuits]
Mads Barnkob
May 19, 2019, 11:24:46 AM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
flyrod
May 19, 2019, 03:22:54 AM
post Re: Are bleeder resistors necessary if I can easily discharge my capacitor?
[Spark gap Tesla coils]
profdc9
May 19, 2019, 03:18:52 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
May 18, 2019, 10:48:59 PM
post Re: Is one of these good?
[Dual Resonant Solid State Tesla coils]
Golddustpeak
May 18, 2019, 04:19:11 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
May 17, 2019, 10:57:17 PM
post Are bleeder resistors necessary if I can easily discharge my capacitor?
[Spark gap Tesla coils]
jpb133
May 17, 2019, 09:41:56 PM
post Re: Is one of these good?
[Dual Resonant Solid State Tesla coils]
Uspring
May 17, 2019, 12:41:17 PM
post ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
82026
May 16, 2019, 04:15:58 PM
post Re: Identification of unknown embedded computer, help needed.
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Fumeaux
May 16, 2019, 02:19:39 PM
post Re: Is one of these good?
[Dual Resonant Solid State Tesla coils]
Golddustpeak
May 16, 2019, 01:50:44 PM
post Re: Is one of these good?
[Dual Resonant Solid State Tesla coils]
Uspring
May 16, 2019, 12:17:01 PM
post Re: Identification of unknown embedded computer, help needed.
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Fumeaux
May 16, 2019, 08:45:15 AM
post Re: Identification of unknown embedded computer, help needed.
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Mads Barnkob
May 15, 2019, 11:49:59 PM
post Re: Identification of unknown embedded computer, help needed.
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Hydron
May 15, 2019, 10:51:33 PM
post Identification of unknown embedded computer, help needed.
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Mads Barnkob
May 15, 2019, 09:35:41 PM
post Re: Is one of these good?
[Dual Resonant Solid State Tesla coils]
Golddustpeak
May 15, 2019, 05:07:20 PM
post Re: Mounting LCD CFL's around DRSSTC?
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
May 15, 2019, 12:46:33 PM
post Re: General Oscilloscope Probing Techniques for (DR)SSTC h-bridge
[Beginners]
Mads Barnkob
May 15, 2019, 10:08:11 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30