Author Topic: Up to 9 half-bridges of FS35R12 IGBTs in parallel, per board...  (Read 154 times)

Offline Mads Barnkob

  • Administrator
  • High Voltage Senior
  • *****
  • Posts: 817
  • Karma: +6/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Up to 9 half-bridges of FS35R12 IGBTs in parallel, per board...
« on: October 08, 2018, 09:25:14 PM »
obvious click-bait head line, but I got no plans... so what to call to it :)

I got these inverter boards from a large 60 kVA UPS system where each cabinet had 4 of these modules inside.

It consisted of 10 FS35R12 IGBT bricks, which is a 3 phased full bridge module, but here they used 2 of these modules for a halfbridge where all 3 "halfbridges" inside the module was used in parallel.

There is a common DC bus supply for the 3 phases, the other 2 halfbridge inverters was either PFC or intermediate inverters, so I removed those and I now have a board with 3 halfbridges that consists of 3 parallel halfbridges.

So if I parallel these 3 outputs I would have 9 parallel halfbridges where each igbt die is rated for 70 Apeak, which is a little low, but with the huge thermal mass that 9 parallel bridges gives, this could properly be pushed above 100A without too much trouble.

At these low peak currents I think there is only one plan for these boards, a QCWDRSSTC. I could try even longer than normal on-times due to the low peak current or as I have 5 of these boards and extra IGBT modules, I could run 2 or more interleaved to allow more time for cooling.



Anyone got comments or suggestions to this plan?
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

High Voltage Forum

Up to 9 half-bridges of FS35R12 IGBTs in parallel, per board...
« on: October 08, 2018, 09:25:14 PM »

 


* Recent Topics and Posts

post spectral analysis of Tesla coils
[Spark gap Tesla coils]
Physikfan
December 15, 2018, 02:24:20 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
DashApple
December 14, 2018, 10:21:25 PM
post Re: DRSSTC design guide - progress report
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 14, 2018, 08:38:52 PM
post Re: DRSSTC design guide - progress report
[Dual Resonant Solid State Tesla coils]
Uspring
December 13, 2018, 12:23:30 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 12, 2018, 11:57:02 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 12, 2018, 01:15:30 PM
post Re: DRSSTC design guide - progress report
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 12, 2018, 01:00:34 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 12, 2018, 11:45:08 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 11, 2018, 09:13:49 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 11, 2018, 12:03:54 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 10, 2018, 12:25:15 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 10, 2018, 11:13:38 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 10, 2018, 09:18:24 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Mads Barnkob
December 10, 2018, 09:13:37 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 10, 2018, 02:18:59 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
sjsimmo
December 09, 2018, 11:09:34 PM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Fumeaux
December 09, 2018, 10:23:38 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 09, 2018, 06:05:02 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Jesjes
December 09, 2018, 04:50:56 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Laci
December 08, 2018, 12:52:41 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 08, 2018, 09:51:47 AM
post Huawei RRU3928 1800MHz radio base station teardown (part 1 of 2)
[Radio frequency]
Mads Barnkob
December 06, 2018, 07:49:06 PM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Fumeaux
December 03, 2018, 10:35:13 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
sjsimmo
December 03, 2018, 08:40:43 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Jesjes
December 03, 2018, 05:31:29 AM
post Re: Hacking the IKEA 2000 Watt induction stove (5 parts)
[Electronic circuits]
chjarup
December 02, 2018, 11:44:14 PM
post SSTC-Driver PCB 1.3
[Printed Circuit Board]
Fumeaux
December 02, 2018, 10:25:23 PM
post Re: Hacking the IKEA 2000 Watt induction stove (5 parts)
[Electronic circuits]
Mads Barnkob
December 02, 2018, 04:23:16 PM
post Re: Hacking the IKEA 2000 Watt induction stove (5 parts)
[Electronic circuits]
chjarup
December 02, 2018, 12:12:57 PM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Mads Barnkob
December 02, 2018, 09:57:04 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Fumeaux
December 01, 2018, 09:15:01 PM
post First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Jesjes
December 01, 2018, 03:38:37 AM
post Re: How sensitive are Tesla coils to Arduino boards?
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Laci
November 29, 2018, 08:34:50 PM
post Re: How sensitive are Tesla coils to Arduino boards?
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Netzpfuscher
November 29, 2018, 09:18:47 AM
post Re: My X-Ray Machine
[X-ray]
neukyhm
November 28, 2018, 07:33:44 PM
post Re: My X-Ray Machine
[X-ray]
Mads Barnkob
November 28, 2018, 07:14:52 PM
post My X-Ray Machine
[X-ray]
neukyhm
November 28, 2018, 04:42:32 PM
post Re: How sensitive are Tesla coils to Arduino boards?
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Mads Barnkob
November 28, 2018, 09:55:58 AM
post How sensitive are Tesla coils to Arduino boards?
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Laci
November 27, 2018, 08:50:54 PM
post Re: My First SSTC
[Solid state Tesla coils]
sjsimmo
November 27, 2018, 09:56:16 AM
post Re: My First SSTC
[Solid state Tesla coils]
Mads Barnkob
November 27, 2018, 08:53:35 AM
post Re: My First SSTC
[Solid state Tesla coils]
sjsimmo
November 26, 2018, 02:28:22 AM
post Re: My First SSTC
[Solid state Tesla coils]
pentode
November 23, 2018, 11:18:58 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
November 23, 2018, 06:39:47 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
November 23, 2018, 03:48:47 AM
post Re: Nokia Siemens Flexi BTS base station teardown: Power amplifier (part 1 and 2)
[Radio frequency]
Mads Barnkob
November 22, 2018, 10:03:48 PM
post Re: Usable vacuum tube?
[Vacuum tube Tesla coils]
Mads Barnkob
November 22, 2018, 11:36:49 AM
post Re: Usable vacuum tube?
[Vacuum tube Tesla coils]
sjsimmo
November 22, 2018, 01:17:32 AM
post My First SSTC
[Solid state Tesla coils]
sjsimmo
November 21, 2018, 11:43:46 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
November 20, 2018, 11:12:10 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30