Author Topic: My first DRSSTC  (Read 1042 times)

Offline erdal

  • High Voltage Enthusiast
  • *
  • Posts: 32
  • Karma: +1/-0
    • View Profile
Re: My first DRSSTC
« Reply #20 on: September 27, 2018, 02:15:59 PM »
Hi Mads,
Quote
Did you try to add such close proximity walls in JavaTC? It has a really big effect on the secondary circuit resonant frequency.
Yes, seconder resonant reduce to 210khz to 185 khz. My primary coil is not fully adjusted at the moment, I am planning to make a new adjustable primary winding with 1/4" copper pipe in my hand.

My new full bridge inverter is quite powerful, 6 amp fuse blows at 115v ac. I got dozen of broken fuse :)) I don't want to install 8 or 10 amp fuses for IGBT's health. Clearly I don't think I'll try with 230v ac in the indoor (at home) environment.

MMC cold, heatsink cold but bus cap (2200 uf/400 v) a little hot. Is this normal?

My new One Tesla midi interrupter working very well

Edit: I would recommend the IXGK60N60C2D1 IGBT. It's same to IXGN60N60c2d1 minibrick but TO-264 case. Only 4.5 usd with taxes. digikey or mouser are not in stock, but my local store have ~20000 in stock :)

Finally,
DRSSTC makes a lot of noise, how are you with your neighbors? :))

Levan Polka 85 v AC

Popcorn 115 v AC
« Last Edit: September 27, 2018, 02:51:57 PM by erdal »

Offline erdal

  • High Voltage Enthusiast
  • *
  • Posts: 32
  • Karma: +1/-0
    • View Profile
Re: My first DRSSTC
« Reply #21 on: September 28, 2018, 02:33:06 PM »
I made a new primer. Tuned best point to resonant. I first tried to wrap the PVC pipe. it's not a good idea. Because the coupling was too high, so the sparks from the primer to the secondary. Then I removed the PVC pipe, adjusted the height of the secondary and primery.


Take Five 115 volt AC

Mission Impossible (Fuse Blown)

Offline Mads Barnkob

  • Administrator
  • High Voltage Senior
  • *****
  • Posts: 825
  • Karma: +6/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: My first DRSSTC
« Reply #22 on: October 01, 2018, 01:37:18 PM »
MMC cold, heatsink cold but bus cap (2200 uf/400 v) a little hot. Is this normal?

Finally,
DRSSTC makes a lot of noise, how are you with your neighbors? :))

Good results with all the MIDI playing, makes it worth the effort of building it :)

It sounds like your DC bus capacitors are not suitable for the amount of ripple current you are loading it with, try to do the calculations for your coil as you can see how to do here: http://kaizerpowerelectronics.dk/tesla-coils/drsstc-design-guide/dc-bus-capacitor/

Noise is a serious issue with a DRSSTC and I have had neighbors yelling at me to stop it, especially when we ran the large DRSSTC at 500 BPS 14kW, that was one loud and ear ringing tone :D
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

High Voltage Forum

Re: My first DRSSTC
« Reply #22 on: October 01, 2018, 01:37:18 PM »

 


* Recent Topics and Posts

post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
Today at 12:19:32 AM
post Re: TO-247 IGBT Comparison for High Frequency & Paralleled Operation
[Dual Resonant Solid State Tesla coils]
Laci
December 18, 2018, 10:30:34 PM
post Re: TO-247 IGBT Comparison for High Frequency & Paralleled Operation
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 18, 2018, 09:42:25 PM
post Re: TO-247 IGBT Comparison for High Frequency & Paralleled Operation
[Dual Resonant Solid State Tesla coils]
Laci
December 18, 2018, 09:25:26 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 18, 2018, 12:50:45 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 18, 2018, 10:45:01 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 18, 2018, 09:47:51 AM
post Re: TO-247 IGBT Comparison for High Frequency & Paralleled Operation
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 18, 2018, 03:18:05 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 18, 2018, 02:08:57 AM
post Re: TO-247 IGBT Comparison for High Frequency & Paralleled Operation
[Dual Resonant Solid State Tesla coils]
Fumeaux
December 17, 2018, 10:22:31 PM
post TO-247 IGBT Comparison for High Frequency & Paralleled Operation
[Dual Resonant Solid State Tesla coils]
Laci
December 17, 2018, 09:36:03 PM
post Re: spectral analysis of Tesla coils
[Spark gap Tesla coils]
Mads Barnkob
December 17, 2018, 02:20:01 PM
post Re: DRSSTC design guide - progress report
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 17, 2018, 01:13:34 PM
post Re: spectral analysis of Tesla coils
[Spark gap Tesla coils]
Uspring
December 17, 2018, 01:02:35 PM
post Re: DRSSTC design guide - progress report
[Dual Resonant Solid State Tesla coils]
Uspring
December 17, 2018, 12:33:07 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 17, 2018, 12:26:08 PM
post Re: Building of my first tesla coil
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 17, 2018, 10:42:17 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 17, 2018, 06:49:52 AM
post Re: Building of my first tesla coil
[Dual Resonant Solid State Tesla coils]
Skylex86
December 16, 2018, 09:09:13 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Mads Barnkob
December 16, 2018, 07:48:55 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
NordicGaben
December 16, 2018, 06:13:54 PM
post spectral analysis of Tesla coils
[Spark gap Tesla coils]
Physikfan
December 15, 2018, 02:24:20 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
DashApple
December 14, 2018, 10:21:25 PM
post Re: DRSSTC design guide - progress report
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 14, 2018, 08:38:52 PM
post Re: DRSSTC design guide - progress report
[Dual Resonant Solid State Tesla coils]
Uspring
December 13, 2018, 12:23:30 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 12, 2018, 11:57:02 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 12, 2018, 01:15:30 PM
post Re: DRSSTC design guide - progress report
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 12, 2018, 01:00:34 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 12, 2018, 11:45:08 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 11, 2018, 09:13:49 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 11, 2018, 12:03:54 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 10, 2018, 12:25:15 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 10, 2018, 11:13:38 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 10, 2018, 09:18:24 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Mads Barnkob
December 10, 2018, 09:13:37 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 10, 2018, 02:18:59 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
sjsimmo
December 09, 2018, 11:09:34 PM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Fumeaux
December 09, 2018, 10:23:38 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 09, 2018, 06:05:02 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Jesjes
December 09, 2018, 04:50:56 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Laci
December 08, 2018, 12:52:41 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 08, 2018, 09:51:47 AM
post Huawei RRU3928 1800MHz radio base station teardown (part 1 of 2)
[Radio frequency]
Mads Barnkob
December 06, 2018, 07:49:06 PM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Fumeaux
December 03, 2018, 10:35:13 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
sjsimmo
December 03, 2018, 08:40:43 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Jesjes
December 03, 2018, 05:31:29 AM
post Re: Hacking the IKEA 2000 Watt induction stove (5 parts)
[Electronic circuits]
chjarup
December 02, 2018, 11:44:14 PM
post SSTC-Driver PCB 1.3
[Printed Circuit Board]
Fumeaux
December 02, 2018, 10:25:23 PM
post Re: Hacking the IKEA 2000 Watt induction stove (5 parts)
[Electronic circuits]
Mads Barnkob
December 02, 2018, 04:23:16 PM
post Re: Hacking the IKEA 2000 Watt induction stove (5 parts)
[Electronic circuits]
chjarup
December 02, 2018, 12:12:57 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30