Author Topic: mmc capacitor banks  (Read 423 times)

Offline OakleyC

  • High Voltage Enthusiast
  • *
  • Posts: 4
  • Karma: +0/-0
    • View Profile
mmc capacitor banks
« on: September 12, 2018, 11:18:07 AM »
Hi all :)

I have been building a dual MOT 110mm tesla coil. I want to make/buy my capacitors now. My question is, am I better off making my own flat capacitor (as rimstarorg made his but with like 150nf capacitance) or buying something similar these Capacitors.

Will these work? They seem a lot cheaper than the cornell-dubilier capacitors. I am aiming for around 150nf at 10kv.

Thanks for your time.

OakleyC


*edit
They also have these ones here.
I calculated I will need 30 to make a 204nf 10kv bank which I think is cheaper than buying lots of smaller caps.
« Last Edit: September 12, 2018, 11:31:04 AM by OakleyC »

Offline Hydron

  • Administrator
  • High Voltage Technician
  • *****
  • Posts: 188
  • Karma: +4/-0
    • View Profile
Re: mmc capacitor banks
« Reply #1 on: September 12, 2018, 04:16:38 PM »
I believe that others have asked about the same capacitors on the forum, I don't remember the exact conclusion (I believe they have actually been tested) but I personally was and still am rather dubious of something without proper specs or datasheet. They don't even state the dielectric material!

Offline OakleyC

  • High Voltage Enthusiast
  • *
  • Posts: 4
  • Karma: +0/-0
    • View Profile
Re: mmc capacitor banks
« Reply #2 on: September 13, 2018, 02:09:09 AM »
Hmm good point on not having a datasheet! What about making my own flat capacitor with pp sheets and aluminium foil? I have seen tesla coils with 50nf in beer bottle capacitors working well but I don't want to work with liquid and high voltage :-\ I would rather have it dry (or maybe oil soaked if i have too but I am only running it at 4.2kv). I had a bit of a look around and found loneoceans post on capacitors. I have a very tight budget though and would rather only spend $50 on caps. All of those caps are like $3+ each which is too much when i'm going to buy like 100 of them. Is it ok to link 4hv and other forums to here?

Offline profdc9

  • High Voltage Technician
  • ***
  • Posts: 180
  • Karma: +4/-0
    • View Profile
Re: mmc capacitor banks
« Reply #3 on: September 14, 2018, 04:50:48 PM »
I actually used the capacitors at hvstuff and they worked.  I have used these capacitors
 
http://hvstuff.com/0-04uf-10kv-high-voltage-capacitor-hv-tesla-coil-ham
http://hvstuff.com/0-1uf-10kv-high-voltage-capacitor-hv-tesla-coil-ham

Also might be useful

http://hvstuff.com/0-02uf-15kv-high-voltage-capacitor-hv-tesla-coil-ham
http://hvstuff.com/0-01uf-20kv-high-voltage-capacitor-hv-tesla-coil-ham
http://hvstuff.com/2kv-0-15uf-high-voltage-capacitor-hv-tesla-coil-ham


You may not want to get one big capacitor.  The peak current ratings tend to be 250 A or so, so its better to use several smaller capacitors in parallel.

Dan

Online Mads Barnkob

  • Administrator
  • High Voltage Senior
  • *****
  • Posts: 822
  • Karma: +6/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: mmc capacitor banks
« Reply #4 on: September 17, 2018, 08:52:32 AM »
Hi Oakley

Those are the "good and old" "Panasonic" capacitors, the reason I write both in situation marks is that they were the best back then, as pulse film capacitors was out of the reach for the amateur and it used to be Panasonic that made them, that is hardly the case anymore :)

I once found the specs and added the panasonics to my MMC calculator, so take a look there: http://kaizerpowerelectronics.dk/calculators/mmc-calculator/

Look at the Panasonic ECWH16333, Panasonic ECWH16473 and Panasonic ECWH16563: http://kaizerpowerelectronics.dk/theory/good-mmc-capacitors/
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline OakleyC

  • High Voltage Enthusiast
  • *
  • Posts: 4
  • Karma: +0/-0
    • View Profile
Re: mmc capacitor banks
« Reply #5 on: September 28, 2018, 06:26:39 AM »
Ok thank you all for all the information! I think I will try making my own polyethylene and aluminium foil capacitor. If the results of that are poor I will buy the cheap china capacitors. If they are all bad i will save up for a cornell dublier capacitor bank.

 :) Oakley

Online Mads Barnkob

  • Administrator
  • High Voltage Senior
  • *****
  • Posts: 822
  • Karma: +6/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: mmc capacitor banks
« Reply #6 on: September 28, 2018, 02:08:57 PM »
Ok thank you all for all the information! I think I will try making my own polyethylene and aluminium foil capacitor. If the results of that are poor I will buy the cheap china capacitors. If they are all bad i will save up for a cornell dublier capacitor bank.

 :) Oakley

Good luck with building your own :) You are going to learn a lot about creeping distances, field shaping and the importance of removing air in order to avoid corona discharges/losses/damages. Building your own can be cheap but not very effective. I would advise you on trying to roll it instead of making a stack of flat sheets. Roll it insanely tight around a larger diameter pipe to get good compression from the middle and out.

Inbetween getting CDE 942C and cheap chinese capacitors is the surplus market of large quantities of brand name leftovers from the industry, check out a good seller like this: http://www.ebaystores.co.uk/zhoefler/Elektronikbauteile-allgemein-/_i.html?rt=nc&_nkw=capacitor&_fsub=2&_sacat=zhoefler&_sid=26870231&_trksid=p4634.c0.m14.l1581&_pgn=3

There is a wide range of cheap 20-100 pieces in a lot MKP capacitors of various capacitance and voltage rating, some of them are vital for a MMC, depending on how much you are willing to solder together :)
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

High Voltage Forum

Re: mmc capacitor banks
« Reply #6 on: September 28, 2018, 02:08:57 PM »

 


* Recent Topics and Posts

post Re: spectral analysis of Tesla coils
[Spark gap Tesla coils]
Mads Barnkob
Today at 02:20:01 PM
post Re: DRSSTC design guide - progress report
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
Today at 01:13:34 PM
post Re: spectral analysis of Tesla coils
[Spark gap Tesla coils]
Uspring
Today at 01:02:35 PM
post Re: DRSSTC design guide - progress report
[Dual Resonant Solid State Tesla coils]
Uspring
Today at 12:33:07 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
Today at 12:26:08 PM
post Re: Building of my first tesla coil
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
Today at 10:42:17 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
Today at 06:49:52 AM
post Re: Building of my first tesla coil
[Dual Resonant Solid State Tesla coils]
Skylex86
December 16, 2018, 09:09:13 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Mads Barnkob
December 16, 2018, 07:48:55 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
NordicGaben
December 16, 2018, 06:13:54 PM
post spectral analysis of Tesla coils
[Spark gap Tesla coils]
Physikfan
December 15, 2018, 02:24:20 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
DashApple
December 14, 2018, 10:21:25 PM
post Re: DRSSTC design guide - progress report
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 14, 2018, 08:38:52 PM
post Re: DRSSTC design guide - progress report
[Dual Resonant Solid State Tesla coils]
Uspring
December 13, 2018, 12:23:30 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 12, 2018, 11:57:02 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 12, 2018, 01:15:30 PM
post Re: DRSSTC design guide - progress report
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 12, 2018, 01:00:34 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 12, 2018, 11:45:08 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 11, 2018, 09:13:49 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 11, 2018, 12:03:54 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 10, 2018, 12:25:15 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 10, 2018, 11:13:38 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
December 10, 2018, 09:18:24 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Mads Barnkob
December 10, 2018, 09:13:37 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 10, 2018, 02:18:59 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
sjsimmo
December 09, 2018, 11:09:34 PM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Fumeaux
December 09, 2018, 10:23:38 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 09, 2018, 06:05:02 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Jesjes
December 09, 2018, 04:50:56 AM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
Laci
December 08, 2018, 12:52:41 PM
post Re: My First DRSSTC
[Dual Resonant Solid State Tesla coils]
sjsimmo
December 08, 2018, 09:51:47 AM
post Huawei RRU3928 1800MHz radio base station teardown (part 1 of 2)
[Radio frequency]
Mads Barnkob
December 06, 2018, 07:49:06 PM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Fumeaux
December 03, 2018, 10:35:13 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
sjsimmo
December 03, 2018, 08:40:43 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Jesjes
December 03, 2018, 05:31:29 AM
post Re: Hacking the IKEA 2000 Watt induction stove (5 parts)
[Electronic circuits]
chjarup
December 02, 2018, 11:44:14 PM
post SSTC-Driver PCB 1.3
[Printed Circuit Board]
Fumeaux
December 02, 2018, 10:25:23 PM
post Re: Hacking the IKEA 2000 Watt induction stove (5 parts)
[Electronic circuits]
Mads Barnkob
December 02, 2018, 04:23:16 PM
post Re: Hacking the IKEA 2000 Watt induction stove (5 parts)
[Electronic circuits]
chjarup
December 02, 2018, 12:12:57 PM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Mads Barnkob
December 02, 2018, 09:57:04 AM
post Re: First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Fumeaux
December 01, 2018, 09:15:01 PM
post First SSTC build, need help troubleshooting
[Solid state Tesla coils]
Jesjes
December 01, 2018, 03:38:37 AM
post Re: How sensitive are Tesla coils to Arduino boards?
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Laci
November 29, 2018, 08:34:50 PM
post Re: How sensitive are Tesla coils to Arduino boards?
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Netzpfuscher
November 29, 2018, 09:18:47 AM
post Re: My X-Ray Machine
[X-ray]
neukyhm
November 28, 2018, 07:33:44 PM
post Re: My X-Ray Machine
[X-ray]
Mads Barnkob
November 28, 2018, 07:14:52 PM
post My X-Ray Machine
[X-ray]
neukyhm
November 28, 2018, 04:42:32 PM
post Re: How sensitive are Tesla coils to Arduino boards?
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Mads Barnkob
November 28, 2018, 09:55:58 AM
post How sensitive are Tesla coils to Arduino boards?
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Laci
November 27, 2018, 08:50:54 PM
post Re: My First SSTC
[Solid state Tesla coils]
sjsimmo
November 27, 2018, 09:56:16 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30