Author Topic: Choosing Primary impedance and Fres  (Read 509 times)

Offline Nijin

  • High Voltage Enthusiast
  • *
  • Posts: 15
  • Karma: +1/-0
    • View Profile
Choosing Primary impedance and Fres
« on: August 03, 2018, 10:34:21 AM »
Hello coilers,

Last week I finished my DRSSTC and the first test gave me 240cm of spark.
My goal is 3m and I have many tracks of improvement. I wondering how can I choose the Primary Impedance for a given frequency and the impact of it.

I use GTO capacitors rated at 3,5uF 1500Vdc per caps.

With my primary coil, I can change my primary caps for 388nF (9 GTO in series), 435nF (8 GTO in series) or 500nF (7 GTO in series) to stay between [52-60]kHz depending how much I want to detune my coil. I've done some simulation with different L C and Fres values to calcultate Z surge, it's between 5,64 and 7 depending F res chosen.



Ocd is set at 1350 but I can push it at 1700A easily with SKM400GB125D IGBT.

Based on your experience wich primary capacitance is the best to perform the biggest streamer ?
Everything is a fuse if you pass enough current

Offline Mads Barnkob

  • Administrator
  • High Voltage Senior
  • *****
  • Posts: 883
  • Karma: +8/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Choosing Primary impedance and Fres
« Reply #1 on: August 03, 2018, 12:42:51 PM »
Congratulations on finishing your DRSSTC!

Lovely video :)

Longer sparks are a product of a higher energy transfer, the biggest effect from a larger MMC is first and foremost much brighter sparks. Look at coils like Kizmo's BiggerDR and Roy Piepers DRSSTC, both have a 1 uF or 1.5 uF MMC, but their sparks are not getting that much longer as the short transfer time limits the system that way.

For a coil you size I would not go below 500 nF, the smaller MMC capacitance will only result in longer on-time needed to produce just as/longer sparks.
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline Nijin

  • High Voltage Enthusiast
  • *
  • Posts: 15
  • Karma: +1/-0
    • View Profile
Re: Choosing Primary impedance and Fres
« Reply #2 on: August 04, 2018, 11:09:53 AM »
Thank you Mads for your answer  :D

I think the best way is to test both 438nF and 500nF. Futhermore, it will reduce the maximum number of turns of my primary and the price ahah
Everything is a fuse if you pass enough current

Offline Uspring

  • High Voltage Experimenter
  • **
  • Posts: 77
  • Karma: +5/-0
    • View Profile
Re: Choosing Primary impedance and Fres
« Reply #3 on: August 04, 2018, 11:44:50 AM »
I enjoyed your video :)
A larger MMC will cause a faster rampup of primary energy, so the higher notes usually limited by short bursts will be louder. On the other hand you might not be able to run long bursts at all since the OCD will limit the length. For biggest arcs, given that you won't cut off the burst by the interruptor, the primary Z should be chosen, so that the OCD will barely not be triggered.

Can you tell us, where your peak primary currents are at and whether your OCD is triggered regularly? If the latter is the case, you should reduce the MMC. If the peak current always stays well below the OCD limit, you should increase the MMC capacitance or detune a bit more.


Offline Nijin

  • High Voltage Enthusiast
  • *
  • Posts: 15
  • Karma: +1/-0
    • View Profile
Re: Choosing Primary impedance and Fres
« Reply #4 on: August 04, 2018, 12:15:39 PM »
I will give you more details about primary current when I will return at school in september, I just tested the coil last week but without any measures and tuning (I think the primary is too detuned for the secondary).
Everything is a fuse if you pass enough current

Offline Hydron

  • Administrator
  • High Voltage Engineer
  • *****
  • Posts: 201
  • Karma: +4/-0
    • View Profile
Re: Choosing Primary impedance and Fres
« Reply #5 on: August 04, 2018, 12:47:06 PM »
I found that I got similar spark lengths, but different behaviour, when tuning primary below (i.e. comes into tune with longer streamers) or near/above the secondary. The streamers were "crazier" when tuned below secondary, but MIDI worked better when tuned near/above, so the choice may also depend on how you plan to run the coil. It sounds like you have the flexibility to do either, and those IGBTs are nice and fast, easily able to do 60kHz or more (where did you get them?).

Offline Nijin

  • High Voltage Enthusiast
  • *
  • Posts: 15
  • Karma: +1/-0
    • View Profile
Re: Choosing Primary impedance and Fres
« Reply #6 on: August 04, 2018, 04:48:00 PM »
The coil was design to represent my engineering school during events, we want to make long spark and play music so I think the tuning will change depending where I present it ( I don't think I'm allowed to make 3m spark in a classroom  ;D ). I order IGBT on rs-online, they was paid by my school with the DC bus caps but recently I saw on semikron website that you can order samples IGBT brick. I didn't tried yet.
Everything is a fuse if you pass enough current

High Voltage Forum

Re: Choosing Primary impedance and Fres
« Reply #6 on: August 04, 2018, 04:48:00 PM »

 


* Recent Topics and Posts

post Re: My first DRSSTC on bricks
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
Today at 08:48:51 AM
post Re: How do I test the max. Ipk of IBGT
[Dual Resonant Solid State Tesla coils]
VNTC
Today at 04:54:44 AM
post Re: Primary-Strike Protection Grounding Scheme - Insanity?
[Dual Resonant Solid State Tesla coils]
Teravolt
February 18, 2019, 09:25:24 PM
post Re: My first DRSSTC on bricks
[Dual Resonant Solid State Tesla coils]
Teravolt
February 18, 2019, 09:11:48 PM
post Re: My first DRSSTC on bricks
[Dual Resonant Solid State Tesla coils]
Hydron
February 18, 2019, 06:38:29 PM
post My first DRSSTC on bricks
[Dual Resonant Solid State Tesla coils]
Laci
February 18, 2019, 05:17:53 PM
post Re: Primary-Strike Protection Grounding Scheme - Insanity?
[Dual Resonant Solid State Tesla coils]
Hydron
February 18, 2019, 08:44:19 AM
post Primary-Strike Protection Grounding Scheme - Insanity?
[Dual Resonant Solid State Tesla coils]
nabzim
February 18, 2019, 05:06:18 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
February 18, 2019, 12:13:02 AM
post Re: A place where I can buy a fiber cable/reciever/transmitter for SSTC interrupter
[Light, lasers and optics]
Laci
February 17, 2019, 08:22:04 PM
post A place where I can buy a fiber cable/reciever/transmitter for SSTC interrupter
[Light, lasers and optics]
FilipŠebík
February 17, 2019, 07:04:54 AM
post Re: How do I test the max. Ipk of IBGT
[Dual Resonant Solid State Tesla coils]
VNTC
February 17, 2019, 03:16:00 AM
post It's been a while since I dabbled:
[Solid state Tesla coils]
T3sl4co1l
February 16, 2019, 06:26:43 PM
post Re: SSTC build as per Steve Ward's Mini SSTC - Final Design
[Solid state Tesla coils]
Mads Barnkob
February 16, 2019, 12:50:30 PM
post Re: How do I test the max. Ipk of IBGT
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
February 16, 2019, 12:47:45 PM
post How do I test the max. Ipk of IBGT
[Dual Resonant Solid State Tesla coils]
VNTC
February 16, 2019, 05:03:21 AM
post Re: SSTC build as per Steve Ward's Mini SSTC - Final Design
[Solid state Tesla coils]
Thunderstruck
February 16, 2019, 02:16:27 AM
post Re: Aliexpress Yunbao pulse skipping Product Guide manual
[Dual Resonant Solid State Tesla coils]
black.yang
February 15, 2019, 08:54:20 AM
post Re: Aliexpress Yunbao pulse skipping Product Guide manual
[Dual Resonant Solid State Tesla coils]
Weston
February 15, 2019, 07:40:34 AM
post Re: Resistor tolerance?
[Beginners]
kamelryttarn
February 14, 2019, 02:27:18 PM
post Re: OneTesla Clone ** Urgent help needed!!
[Dual Resonant Solid State Tesla coils]
TonyHV
February 13, 2019, 11:53:07 PM
post Re: OneTesla Clone ** Urgent help needed!!
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
February 13, 2019, 09:27:51 PM
post Re: OneTesla Clone ** Urgent help needed!!
[Dual Resonant Solid State Tesla coils]
TonyHV
February 13, 2019, 09:06:28 PM
post Re: Aliexpress Yunbao pulse skipping Product Guide manual
[Dual Resonant Solid State Tesla coils]
black.yang
February 13, 2019, 06:57:22 PM
post Aliexpress Yunbao pulse skipping Product Guide manual
[Dual Resonant Solid State Tesla coils]
black.yang
February 13, 2019, 06:55:42 PM
post Re: OneTesla Clone ** Urgent help needed!!
[Dual Resonant Solid State Tesla coils]
pentode
February 13, 2019, 06:44:22 PM
post Re: OneTesla Clone ** Urgent help needed!!
[Dual Resonant Solid State Tesla coils]
TonyHV
February 13, 2019, 05:23:58 PM
post Re: OneTesla Clone ** Urgent help needed!!
[Dual Resonant Solid State Tesla coils]
TonyHV
February 13, 2019, 05:14:58 PM
post Re: OneTesla Clone ** Urgent help needed!!
[Dual Resonant Solid State Tesla coils]
Teravolt
February 13, 2019, 03:12:37 PM
post Re: OneTesla Clone ** Urgent help needed!!
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
February 13, 2019, 02:47:49 PM
post Re: OneTesla Clone ** Urgent help needed!!
[Dual Resonant Solid State Tesla coils]
TonyHV
February 13, 2019, 01:57:55 PM
post Re: OneTesla Clone ** Urgent help needed!!
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
February 13, 2019, 01:53:36 PM
post Re: OneTesla Clone ** Urgent help needed!!
[Dual Resonant Solid State Tesla coils]
TonyHV
February 13, 2019, 01:45:53 PM
post Re: OneTesla Clone ** Urgent help needed!!
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
February 13, 2019, 12:58:48 PM
post Re: OneTesla Clone ** Urgent help needed!!
[Dual Resonant Solid State Tesla coils]
TonyHV
February 13, 2019, 12:35:10 PM
post Re: Homemade flyback on 60N60DLF full bridge
[Transformer (ferrite core)]
Platinum
February 12, 2019, 09:17:29 PM
post Video gear & workflow: Canon 5D mk3, Rødelink, FPS1000HD and more
[DSLR]
Mads Barnkob
February 12, 2019, 08:51:43 AM
post Re: STB16PF06L
[Dual Resonant Solid State Tesla coils]
pentode
February 12, 2019, 08:16:33 AM
post Re: Homemade flyback on 60N60DLF full bridge
[Transformer (ferrite core)]
Mads Barnkob
February 11, 2019, 11:06:05 PM
post Re: SSTC build as per Steve Ward's Mini SSTC - Final Design
[Solid state Tesla coils]
Mads Barnkob
February 11, 2019, 10:58:06 PM
post Re: STB16PF06L
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
February 11, 2019, 10:18:39 PM
post Re: SSTC build as per Steve Ward's Mini SSTC - Final Design
[Solid state Tesla coils]
Laci
February 11, 2019, 04:28:24 PM
post STB16PF06L
[Dual Resonant Solid State Tesla coils]
pentode
February 11, 2019, 04:21:54 PM
post Re: SSTC build as per Steve Ward's Mini SSTC - Final Design
[Solid state Tesla coils]
Thunderstruck
February 11, 2019, 11:55:44 AM
post Re: Homemade flyback on 60N60DLF full bridge
[Transformer (ferrite core)]
Hydron
February 11, 2019, 08:13:07 AM
post Homemade flyback on 60N60DLF full bridge
[Transformer (ferrite core)]
Platinum
February 10, 2019, 08:36:12 PM
post Resistor tolerance?
[Beginners]
kamelryttarn
February 10, 2019, 05:46:39 PM
post Re: Help! IBGT 60N60 has been destroyed a lot by my coil
[Dual Resonant Solid State Tesla coils]
sjsimmo
February 09, 2019, 09:19:49 AM
post Help! IBGT 60N60 has been destroyed a lot by my coil
[Dual Resonant Solid State Tesla coils]
VNTC
February 09, 2019, 05:32:59 AM
post Re: DRSSTC design guide - progress report
[Dual Resonant Solid State Tesla coils]
flyglas
February 08, 2019, 05:10:29 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30