Author Topic: Calculating Hard-Switching losses  (Read 1309 times)

Offline Phoenix

  • High Voltage Experimenter
  • **
  • Posts: 70
  • Karma: +1/-0
    • View Profile
Calculating Hard-Switching losses
« on: July 31, 2018, 05:37:45 PM »
Hello  :)

I would like to calculate the maximum frequency i can drive an IGBT-Brick within its thermal limitation. I am using SKM200GB128D Bricks.

I am calculating the losses for 180A Hardswitching and a frequency of 20kHz. I need to find out the turn on/off energy first using the datasheet.


And here is my question: When reading the energy of the chart, do i need to use the 180A of current or the change of current (dI/dt)? The change of current would only be around 22.6A/µs high for 180A at 20kHz, which would result in much lower turn on/off energies.

Greetings,
Phoenix


Online Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1179
  • Karma: +17/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Calculating Hard-Switching losses
« Reply #1 on: July 31, 2018, 06:54:55 PM »
It is your peak current, that is how I calculated it for soft-switching here: http://kaizerpowerelectronics.dk/tesla-coils/drsstc-design-guide/igbts/

I guess you can use my example all the way through, just ignore the reduction factors for resonant switching that I use :)
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline Phoenix

  • High Voltage Experimenter
  • **
  • Posts: 70
  • Karma: +1/-0
    • View Profile
Re: Calculating Hard-Switching losses
« Reply #2 on: July 31, 2018, 08:06:16 PM »
Thank you for your reply  :)

I have already followed your guide for the calculations but i am stuck at that point. In this application i am only switching  an inductive load, which results in a triangular waveform. The IGBT's always switch at the peaks of this waveform (180A). There is no resonance circuit, so the IGBT's always switch at full current. Because of that, i think i have to read the chart at 180A of current. But if i read the chart at the operating current, i can't keep up with the manufacturers claim of 220A at 20kHz with a junction temperature of 150°C and a case temperature of 80°C. Here are my calculations:


As you see i am only able to switch at a maximum frequency of 8.462kHz but according to the datasheet the bricks should be able to switch 20kHz at 220A.

Is there something wrong with my calculations?

Edit: I just tried something new and i think i have found the problem: A square wave has a RMS-Factor of 1, but a triangular wave only has a factor of 0,577. The maximum current rating in the datasheet is for DC, so there are no switching losses included. If i put in the numbers for 127A (220*0,577) into the equations, the result is 23,462 kHz and it should work for my inverter. Could this result be correct?

Greetings,
Phoenix
« Last Edit: July 31, 2018, 08:54:19 PM by Phoenix »

Online Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1179
  • Karma: +17/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Calculating Hard-Switching losses
« Reply #3 on: July 31, 2018, 09:24:55 PM »
I was just about to mention that, just like I had to reduce for soft-switching short pulses, as hard-switching is seen as a square wave, a triangle waveform would also have to use a reduction factor, but you already figured that out :)
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline Phoenix

  • High Voltage Experimenter
  • **
  • Posts: 70
  • Karma: +1/-0
    • View Profile
Re: Calculating Hard-Switching losses
« Reply #4 on: July 31, 2018, 10:27:35 PM »
I have now used the reduction factor for my 180A which gives me about 104A RMS. I used the RMS value for the CE Voltage and in the calculation for the conduction losses. But i have not used it for the turn on/off energy, because the IGBT still has to switch the 180A peak.

According to my calculations, if the junction has a temperature of 125°C and the Case has a temperature of 50°C, i can run my Inverter up to 20,6kHz. I also converted the equation to tell me the temperature difference between junction and case, at 20kHz the difference would be 73°C. I could now use a circuit which cuts of the supply voltage to the inverter using a relay, when the case temperature reachs 57°C, so the junction would never get hotter than 130°C  :D

Greetings,
Phoenix
« Last Edit: July 31, 2018, 11:57:15 PM by Phoenix »

Offline rikkitikkitavi

  • High Voltage Enthusiast
  • *
  • Posts: 28
  • Karma: +1/-0
    • View Profile
Re: Calculating Hard-Switching losses
« Reply #5 on: August 17, 2018, 03:44:38 PM »
Just a thought, wouldnt average value instead of RMS be more accurate?

The loss is the integral of the current*voltage across the switching device during the switching event.
A man can not have to many variacs

Offline Phoenix

  • High Voltage Experimenter
  • **
  • Posts: 70
  • Karma: +1/-0
    • View Profile
Re: Calculating Hard-Switching losses
« Reply #6 on: August 17, 2018, 04:47:21 PM »
I only used the RMS Value for the calculation of the conduction losses during the ON-State.

For the losses during the switching event, i used the full 180A, because the IGBT's switch at the current maximum.

Online Hydron

  • Administrator
  • High Voltage Engineer
  • *****
  • Posts: 273
  • Karma: +8/-0
    • View Profile
Re: Calculating Hard-Switching losses
« Reply #7 on: August 18, 2018, 03:26:03 PM »
Conduction losses for an IGBT should probably be done with the average (mean) current rather than RMS - they behave more like a diode than a resistor in forward conduction. RMS is appropriate for MOSFETs though, and it probably won't make a lot of difference anyway.

High Voltage Forum

Re: Calculating Hard-Switching losses
« Reply #7 on: August 18, 2018, 03:26:03 PM »

 


* Recent Topics and Posts

post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
Today at 03:35:40 PM
post Re: Why did 4HV die??
[General chatting]
John123
Today at 03:21:07 PM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
Mads Barnkob
Today at 03:04:28 PM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
Today at 02:57:45 PM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
kamelryttarn
Today at 11:23:48 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
Mads Barnkob
Today at 10:27:54 AM
post Re: Worlds Weirdest Microwave Oven, From A Weapons Factory - The Husqvarna Cupol
[Transformer (iron core)]
Mads Barnkob
Today at 10:20:17 AM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
Mads Barnkob
Today at 10:16:32 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
Today at 06:04:28 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
davekni
Today at 05:28:54 AM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
davekni
Today at 04:12:29 AM
post Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
December 09, 2019, 10:52:59 PM
post Replacement guide for Windows Media Center
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
MRMILSTAR
December 09, 2019, 08:29:16 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
Uspring
December 09, 2019, 04:23:33 PM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
MRMILSTAR
December 09, 2019, 03:59:02 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 09, 2019, 03:41:42 PM
post Possible use for large inductor (laminated core)
[Transformer (iron core)]
kamelryttarn
December 09, 2019, 09:43:11 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
December 09, 2019, 12:53:57 AM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
davekni
December 08, 2019, 09:57:51 PM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
MRMILSTAR
December 08, 2019, 05:28:09 PM
post Aethra CCD Webcam Teardown - From Back When Streaming Was Expensive!
[Electronic circuits]
Mads Barnkob
December 08, 2019, 01:33:30 PM
post Platter resistance & inductance
[Induction launchers, coil guns and rails guns]
klugesmith
December 08, 2019, 11:41:00 AM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
davekni
December 08, 2019, 06:50:11 AM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
plasma
December 08, 2019, 12:00:00 AM
post CW multiplier resistor string suggestions
[Voltage Multipliers]
MRMILSTAR
December 07, 2019, 11:32:49 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 07, 2019, 09:54:31 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 07, 2019, 09:48:21 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 07, 2019, 08:59:57 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
MRMILSTAR
December 06, 2019, 08:35:29 PM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 06, 2019, 05:19:26 AM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
davekni
December 06, 2019, 03:48:34 AM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
the_anomaly
December 06, 2019, 03:35:39 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
AstRii
December 06, 2019, 01:27:03 AM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 05, 2019, 11:38:59 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
Mads Barnkob
December 05, 2019, 07:33:01 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
sjsimmo
December 05, 2019, 11:09:20 AM
post Cost reduction in consumer electrics
[Electronic circuits]
klugesmith
December 05, 2019, 07:25:20 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 05, 2019, 05:52:11 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 05, 2019, 05:21:07 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 04, 2019, 06:05:11 PM
post Re: Full bridge showing half the voltage
[Beginners]
shrad
December 04, 2019, 02:57:02 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
Uspring
December 04, 2019, 12:40:51 PM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 04, 2019, 11:20:25 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 04, 2019, 08:28:15 AM
post Re: Full bridge showing half the voltage
[Beginners]
klugesmith
December 04, 2019, 07:41:21 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
MRMILSTAR
December 04, 2019, 05:15:49 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 04, 2019, 05:06:39 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 04, 2019, 04:31:16 AM
post Re: Full bridge showing half the voltage
[Beginners]
davekni
December 04, 2019, 04:26:38 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 04, 2019, 04:10:16 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30