Author Topic: Calculating Hard-Switching losses  (Read 977 times)

Offline Phoenix

  • High Voltage Experimenter
  • **
  • Posts: 63
  • Karma: +1/-0
    • View Profile
Calculating Hard-Switching losses
« on: July 31, 2018, 05:37:45 PM »
Hello  :)

I would like to calculate the maximum frequency i can drive an IGBT-Brick within its thermal limitation. I am using SKM200GB128D Bricks.

I am calculating the losses for 180A Hardswitching and a frequency of 20kHz. I need to find out the turn on/off energy first using the datasheet.


And here is my question: When reading the energy of the chart, do i need to use the 180A of current or the change of current (dI/dt)? The change of current would only be around 22.6A/µs high for 180A at 20kHz, which would result in much lower turn on/off energies.

Greetings,
Phoenix


Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1070
  • Karma: +16/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Calculating Hard-Switching losses
« Reply #1 on: July 31, 2018, 06:54:55 PM »
It is your peak current, that is how I calculated it for soft-switching here: http://kaizerpowerelectronics.dk/tesla-coils/drsstc-design-guide/igbts/

I guess you can use my example all the way through, just ignore the reduction factors for resonant switching that I use :)
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline Phoenix

  • High Voltage Experimenter
  • **
  • Posts: 63
  • Karma: +1/-0
    • View Profile
Re: Calculating Hard-Switching losses
« Reply #2 on: July 31, 2018, 08:06:16 PM »
Thank you for your reply  :)

I have already followed your guide for the calculations but i am stuck at that point. In this application i am only switching  an inductive load, which results in a triangular waveform. The IGBT's always switch at the peaks of this waveform (180A). There is no resonance circuit, so the IGBT's always switch at full current. Because of that, i think i have to read the chart at 180A of current. But if i read the chart at the operating current, i can't keep up with the manufacturers claim of 220A at 20kHz with a junction temperature of 150°C and a case temperature of 80°C. Here are my calculations:


As you see i am only able to switch at a maximum frequency of 8.462kHz but according to the datasheet the bricks should be able to switch 20kHz at 220A.

Is there something wrong with my calculations?

Edit: I just tried something new and i think i have found the problem: A square wave has a RMS-Factor of 1, but a triangular wave only has a factor of 0,577. The maximum current rating in the datasheet is for DC, so there are no switching losses included. If i put in the numbers for 127A (220*0,577) into the equations, the result is 23,462 kHz and it should work for my inverter. Could this result be correct?

Greetings,
Phoenix
« Last Edit: July 31, 2018, 08:54:19 PM by Phoenix »

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1070
  • Karma: +16/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Calculating Hard-Switching losses
« Reply #3 on: July 31, 2018, 09:24:55 PM »
I was just about to mention that, just like I had to reduce for soft-switching short pulses, as hard-switching is seen as a square wave, a triangle waveform would also have to use a reduction factor, but you already figured that out :)
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline Phoenix

  • High Voltage Experimenter
  • **
  • Posts: 63
  • Karma: +1/-0
    • View Profile
Re: Calculating Hard-Switching losses
« Reply #4 on: July 31, 2018, 10:27:35 PM »
I have now used the reduction factor for my 180A which gives me about 104A RMS. I used the RMS value for the CE Voltage and in the calculation for the conduction losses. But i have not used it for the turn on/off energy, because the IGBT still has to switch the 180A peak.

According to my calculations, if the junction has a temperature of 125°C and the Case has a temperature of 50°C, i can run my Inverter up to 20,6kHz. I also converted the equation to tell me the temperature difference between junction and case, at 20kHz the difference would be 73°C. I could now use a circuit which cuts of the supply voltage to the inverter using a relay, when the case temperature reachs 57°C, so the junction would never get hotter than 130°C  :D

Greetings,
Phoenix
« Last Edit: July 31, 2018, 11:57:15 PM by Phoenix »

Offline rikkitikkitavi

  • High Voltage Enthusiast
  • *
  • Posts: 19
  • Karma: +1/-0
    • View Profile
Re: Calculating Hard-Switching losses
« Reply #5 on: August 17, 2018, 03:44:38 PM »
Just a thought, wouldnt average value instead of RMS be more accurate?

The loss is the integral of the current*voltage across the switching device during the switching event.
A man can not have to many variacs

Offline Phoenix

  • High Voltage Experimenter
  • **
  • Posts: 63
  • Karma: +1/-0
    • View Profile
Re: Calculating Hard-Switching losses
« Reply #6 on: August 17, 2018, 04:47:21 PM »
I only used the RMS Value for the calculation of the conduction losses during the ON-State.

For the losses during the switching event, i used the full 180A, because the IGBT's switch at the current maximum.

Offline Hydron

  • Administrator
  • High Voltage Engineer
  • *****
  • Posts: 242
  • Karma: +7/-0
    • View Profile
Re: Calculating Hard-Switching losses
« Reply #7 on: August 18, 2018, 03:26:03 PM »
Conduction losses for an IGBT should probably be done with the average (mean) current rather than RMS - they behave more like a diode than a resistor in forward conduction. RMS is appropriate for MOSFETs though, and it probably won't make a lot of difference anyway.

High Voltage Forum

Re: Calculating Hard-Switching losses
« Reply #7 on: August 18, 2018, 03:26:03 PM »

 


* Recent Topics and Posts

post Re: You would think this would be easy to find.
[Spark gap Tesla coils]
thedoc298
August 17, 2019, 11:09:16 PM
post Re: You would think this would be easy to find.
[Spark gap Tesla coils]
thedoc298
August 17, 2019, 11:00:32 PM
post Re: You would think this would be easy to find.
[Spark gap Tesla coils]
Fumeaux
August 17, 2019, 09:44:07 PM
post You would think this would be easy to find.
[Spark gap Tesla coils]
thedoc298
August 17, 2019, 09:01:00 PM
post Re: Twin System Build
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
August 17, 2019, 08:06:42 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
Lane
August 17, 2019, 10:45:26 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
Lane
August 17, 2019, 06:21:45 AM
post Re: My second DRSSTC
[Dual Resonant Solid State Tesla coils]
Hydron
August 17, 2019, 12:59:20 AM
post Re: Twin System Build
[Dual Resonant Solid State Tesla coils]
fnordest
August 17, 2019, 12:18:48 AM
post Re: Drsstc 3
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
August 16, 2019, 10:34:46 PM
post Re: Teardown of Danfoss VLT6000 4kW Variable Frequency Drive
[Electronic circuits]
Mads Barnkob
August 16, 2019, 10:26:19 PM
post Re: My second DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
August 16, 2019, 10:19:18 PM
post Re: [Development] Project of an SSTC driver.
[Solid state Tesla coils]
Mads Barnkob
August 16, 2019, 10:07:31 PM
post Re: Suitable capacitors and switches? 10kV
[Capacitor banks]
T3sl4co1l
August 16, 2019, 09:28:35 PM
post Re: Suitable capacitors and switches? 10kV
[Capacitor banks]
ElectroXa
August 16, 2019, 09:17:04 PM
post Re: ESAB Power TIG 200 Welder Teardown
[Electronic circuits]
T3sl4co1l
August 16, 2019, 09:14:36 PM
post ESAB Power TIG 200 Welder Teardown
[Electronic circuits]
Mads Barnkob
August 16, 2019, 08:03:18 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
August 16, 2019, 01:49:53 PM
post Suitable capacitors and switches? 10kV
[Capacitor banks]
MrFox
August 16, 2019, 12:21:36 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
Lane
August 16, 2019, 11:22:45 AM
post Re: Small Phase change build R600a
[General chatting]
DashApple
August 15, 2019, 06:23:40 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
rikkitikkitavi
August 15, 2019, 06:17:55 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
Lane
August 15, 2019, 01:51:04 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
August 14, 2019, 07:05:57 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
Bert911
August 14, 2019, 03:42:34 PM
post Re: Van de Graaf is leaking charge
[Static electricity]
Patric
August 14, 2019, 02:56:49 PM
post Re: Van de Graaf is leaking charge
[Static electricity]
ElectroXa
August 14, 2019, 01:42:21 PM
post Re: My second DRSSTC
[Dual Resonant Solid State Tesla coils]
erdal
August 14, 2019, 12:53:10 PM
post Van de Graaf is leaking charge
[Static electricity]
Patric
August 14, 2019, 09:22:21 AM
post Re: Drsstc 3
[Dual Resonant Solid State Tesla coils]
oneKone
August 14, 2019, 04:39:11 AM
post Re: MMC orientation and variac
[Spark gap Tesla coils]
thedoc298
August 13, 2019, 07:10:31 PM
post Re: MMC orientation and variac
[Spark gap Tesla coils]
MRMILSTAR
August 13, 2019, 05:17:23 AM
post MMC orientation and variac
[Spark gap Tesla coils]
thedoc298
August 12, 2019, 09:54:35 PM
post Re: My second DRSSTC
[Dual Resonant Solid State Tesla coils]
erdal
August 12, 2019, 08:40:16 PM
post Re: Small Phase change build R600a
[General chatting]
Hydron
August 12, 2019, 07:27:23 PM
post Re: Teardown of Danfoss VLT6000 4kW Variable Frequency Drive
[Electronic circuits]
klugesmith
August 12, 2019, 09:18:15 AM
post Re: Teardown of Danfoss VLT6000 4kW Variable Frequency Drive
[Electronic circuits]
shrad
August 12, 2019, 09:06:34 AM
post Re: Teardown of Danfoss VLT6000 4kW Variable Frequency Drive
[Electronic circuits]
klugesmith
August 12, 2019, 09:02:38 AM
post Re: A problem solved with hand tools
[General chatting]
klugesmith
August 12, 2019, 08:29:20 AM
post Re: Ebay [US]: MITSUBISHI CM300 1200V-300A IGBT (30$ a piece)
[Sell / Buy / Trade]
oneKone
August 12, 2019, 05:25:24 AM
post Re: Ebay [US]: MITSUBISHI CM300 1200V-300A IGBT (30$ a piece)
[Sell / Buy / Trade]
acobaugh
August 10, 2019, 08:14:35 PM
post Re: 30% power increase
[Spark gap Tesla coils]
MRMILSTAR
August 08, 2019, 04:18:09 PM
post Re: "LightningStorm" VTTC project
[Vacuum tube Tesla coils]
Bambinz
August 08, 2019, 01:15:11 PM
post Re: Twin System Build
[Dual Resonant Solid State Tesla coils]
Bambinz
August 08, 2019, 12:15:26 PM
post Re: My second DRSSTC
[Dual Resonant Solid State Tesla coils]
Bambinz
August 08, 2019, 11:58:47 AM
post Re: [Development] Project of an SSTC driver.
[Solid state Tesla coils]
Bambinz
August 08, 2019, 11:56:51 AM
post Re: Next Gen DRSSTC
[Dual Resonant Solid State Tesla coils]
Netzpfuscher
August 08, 2019, 10:04:39 AM
post Re: My second DRSSTC
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
August 08, 2019, 08:35:57 AM
post Re: 30% power increase
[Spark gap Tesla coils]
Mads Barnkob
August 08, 2019, 08:33:01 AM
post Re: Using R/C motors as 3 phase generators.
[General chatting]
Patrick
August 07, 2019, 09:16:57 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30