Author Topic: DRSSTC impedance  (Read 1065 times)

Offline Marty

  • High Voltage Enthusiast
  • *
  • Posts: 8
  • Karma: +0/-0
    • View Profile
DRSSTC impedance
« on: July 12, 2018, 08:14:38 PM »
Hi everyone!

After a lot of reading, learning, doing calculations etc. I chose these specs for my medium DRSSTC:

Secondary coil: 20x80cm (8x32"), 0.5mm (24AWG), about 1454 turns, with toroid 81kHz and 48.5kOhm impedance (I want "smaller", but with low frequency about 70-80kHz)
I will be using CM300DY-24H, so I need low frequency to lower switching losses.
I wanted to use 16cm dia secondary, but the frequency will be a bit to high and if I use for example 0.35mm wire dia (27AWG) the frequency will be about the same, but impedance will be far away from "magic 50k".

But I saw other coilers (loneocans etc.) using 16x70cm secondary with 0.35mm wire (1850turns,f=80kHz, Z=61kOhm), so
I´m asking what is better, lower impedance (about 50k) or higher with more turns and more suitable h/d raito ?

Thank you for answers
« Last Edit: July 12, 2018, 11:46:33 PM by Marty »

Offline Teravolt

  • High Voltage Technician
  • ***
  • Posts: 101
  • Karma: +2/-0
    • View Profile
Re: DRSSTC impedance
« Reply #1 on: July 13, 2018, 03:22:21 AM »
a 4:1 is a good ratio and 80KHz I have calculated as 1/4 wavelength   http://www.procato.com/calculator-wavelength-frequency/     when you add a toride to the top and take in consider the distributive capacitance it will be less. when you have an arc from the top it will bring it down farther if you are concerned you could add another foot to the 8" coil or use smaller wire. At resonance your measured impedance should be the resistance of the wire witch is around 25.6 ohm per 1000 Ft. In reality it will be more    https://www.allaboutcircuits.com/textbook/alternating-current/chpt-6/q-and-bandwidth-resonant-circuit/

 I would use a tesla calculator to find your baseline coil and build the secondary and then tailor a primary with the resonant frequency to match using a o-scope and a sweep generator. there is plethora of projects hear

Offline Hydron

  • Administrator
  • High Voltage Engineer
  • *****
  • Posts: 273
  • Karma: +8/-0
    • View Profile
Re: DRSSTC impedance
« Reply #2 on: July 13, 2018, 09:08:00 AM »
Everything will still work if you don't hit the "magic" 50k - this is not an exact number by any means. The 160*700*.35mm type design worked well for me with the exact same IGBTs (pre "magic 50k" knowledge).

If you have the 20cm pipe though then bigger is better!

Offline Marty

  • High Voltage Enthusiast
  • *
  • Posts: 8
  • Karma: +0/-0
    • View Profile
Re: DRSSTC impedance
« Reply #3 on: July 13, 2018, 12:45:17 PM »
Thanks for your reply,
I didn´t buy the pipe yet because they dont have it (maybe some sign :D ).. so if the impedance is not that crucial, I will use 16x70cm and nice skeleton toroid which will also lower f and Z... Again, thank you for helping me with understanding this mystery :D

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1174
  • Karma: +17/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: DRSSTC impedance
« Reply #4 on: July 13, 2018, 09:00:52 PM »
Hi Marty and welcome to HVF

You got a good plan, known and proven to work components.

For a DRSSTC, a coil with a impedance around 50k is just a well-proven design and the performance is documented from numerous builds. Something like the high impedance and arbitrary waveform driven QCW coils really show that the impedance is by far not a determining factor for the performance.

As long as you don't get outside +/- 25k of the 50k, you are in the "safe" zone where it will be able to produce sparks, getting outside these boundaries should only be with experimentation in mind and not to build a well performing DRSSTC.

Looking forward to see much more about your build, please keep us update :)
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

High Voltage Forum

Re: DRSSTC impedance
« Reply #4 on: July 13, 2018, 09:00:52 PM »

 


* Recent Topics and Posts

post Re: Full bridge showing half the voltage
[Beginners]
plasma
Today at 05:19:26 AM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
davekni
Today at 03:48:34 AM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
the_anomaly
Today at 03:35:39 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
AstRii
Today at 01:27:03 AM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 05, 2019, 11:38:59 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
Mads Barnkob
December 05, 2019, 07:33:01 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
sjsimmo
December 05, 2019, 11:09:20 AM
post Cost reduction in consumer electrics
[Electronic circuits]
klugesmith
December 05, 2019, 07:25:20 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 05, 2019, 05:52:11 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 05, 2019, 05:21:07 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 04, 2019, 06:05:11 PM
post Re: Full bridge showing half the voltage
[Beginners]
shrad
December 04, 2019, 02:57:02 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
Uspring
December 04, 2019, 12:40:51 PM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 04, 2019, 11:20:25 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 04, 2019, 08:28:15 AM
post Re: Full bridge showing half the voltage
[Beginners]
klugesmith
December 04, 2019, 07:41:21 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
MRMILSTAR
December 04, 2019, 05:15:49 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 04, 2019, 05:06:39 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 04, 2019, 04:31:16 AM
post Re: Full bridge showing half the voltage
[Beginners]
davekni
December 04, 2019, 04:26:38 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 04, 2019, 04:10:16 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 04, 2019, 12:28:15 AM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 04, 2019, 12:11:32 AM
post Re: HV resistor in oil
[Voltage Multipliers]
johnf
December 03, 2019, 07:58:41 PM
post Re: Driving Nixie-tubes with arduino
[Electronic circuits]
johnf
December 03, 2019, 07:54:08 PM
post Re: Full bridge showing half the voltage
[Beginners]
klugesmith
December 03, 2019, 07:41:00 PM
post Re: Driving Nixie-tubes with arduino
[Electronic circuits]
kamelryttarn
December 03, 2019, 02:14:00 PM
post Re: Driving Nixie-tubes with arduino
[Electronic circuits]
Mads Barnkob
December 03, 2019, 01:24:00 PM
post Re: Driving Nixie-tubes with arduino
[Electronic circuits]
klugesmith
December 03, 2019, 10:45:58 AM
post Driving Nixie-tubes with arduino
[Electronic circuits]
kamelryttarn
December 03, 2019, 09:04:42 AM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 03, 2019, 07:29:48 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 03, 2019, 05:07:28 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 03, 2019, 04:34:46 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 02, 2019, 09:06:07 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
T3sl4co1l
December 02, 2019, 10:51:33 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 02, 2019, 05:49:05 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
December 02, 2019, 04:10:14 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
December 02, 2019, 04:09:37 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 02, 2019, 03:42:16 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 01, 2019, 10:47:18 PM
post Re: HV resistor in oil
[Voltage Multipliers]
Mads Barnkob
December 01, 2019, 09:17:38 PM
post HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 01, 2019, 08:51:31 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 01, 2019, 07:32:44 PM
post Re: Corona on the.... GDT??
[Solid state Tesla coils]
Weston
December 01, 2019, 12:14:57 PM
post Re: SSTC low voltage at gate transformer and heating drivers
[Solid state Tesla coils]
davekni
December 01, 2019, 04:30:10 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
December 01, 2019, 02:56:39 AM
post Re: New to tesla coils, some questions before I start building a SSTC
[Solid state Tesla coils]
Blin
November 30, 2019, 10:28:56 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
November 30, 2019, 09:41:17 PM
post Re: QCW ramp generator
[Dual Resonant Solid State Tesla coils]
shrad
November 30, 2019, 06:12:28 PM
post Re: QCW ramp generator
[Dual Resonant Solid State Tesla coils]
hammertone
November 30, 2019, 04:28:34 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30