Author Topic: Royer induction heater based on kaizerpowerelectronics  (Read 688 times)

Offline symslshrf

  • High Voltage Enthusiast
  • *
  • Posts: 3
  • Karma: +0/-0
    • View Profile
Royer induction heater based on kaizerpowerelectronics
« on: May 31, 2018, 01:16:30 PM »
hello. based on the website that is stated, i have construct a circuit simulation on proteus 8.
however instead of using diodes and zeners to the mosfets, i connect the mosfet from a gate driver then connect it to a microcontroler which is the arduino uno for the switching of the mosfets .

this attachment is my circuit constructed on proteus 8 simulation and please noticed that ir2112 is the virtual gate driver connected to the mosfets.

this attachment is the output waveform measured on oscilloscope on the mosfets.

im looking forward for an assist on my school project.
« Last Edit: May 31, 2018, 01:18:19 PM by symslshrf »

Offline kamelryttarn

  • High Voltage Experimenter
  • **
  • Posts: 92
  • Karma: +0/-0
    • View Profile
Re: Royer induction heater based on kaizerpowerelectronics
« Reply #1 on: June 01, 2018, 09:49:47 AM »
Why do you wish to use a microcontroller? One of the things I like about the Royer circuit is that it is self adjusting.

Offline symslshrf

  • High Voltage Enthusiast
  • *
  • Posts: 3
  • Karma: +0/-0
    • View Profile
Re: Royer induction heater based on kaizerpowerelectronics
« Reply #2 on: June 01, 2018, 12:00:43 PM »
Why do you wish to use a microcontroller? One of the things I like about the Royer circuit is that it is self adjusting.

what do you mean by self adjusting? im using a microcontroller for the switching of the two mosfets. is it not necessary?

Offline kamelryttarn

  • High Voltage Experimenter
  • **
  • Posts: 92
  • Karma: +0/-0
    • View Profile
Re: Royer induction heater based on kaizerpowerelectronics
« Reply #3 on: June 01, 2018, 01:56:05 PM »
The Royer induction heater is self contained. The switching is done automatically based on the capacitance and the inductor value of the LC tank. If you use a microcontroller to force a non-optimal frequency I suspect something might break or at least get hot. And this circuit gets plenty hot as it is, trust me ;)

Offline symslshrf

  • High Voltage Enthusiast
  • *
  • Posts: 3
  • Karma: +0/-0
    • View Profile
Re: Royer induction heater based on kaizerpowerelectronics
« Reply #4 on: June 01, 2018, 02:12:56 PM »
The Royer induction heater is self contained. The switching is done automatically based on the capacitance and the inductor value of the LC tank. If you use a microcontroller to force a non-optimal frequency I suspect something might break or at least get hot. And this circuit gets plenty hot as it is, trust me ;)

thank you sir for this information. can you elaborate more about the automatic switching? or is there some terms or reference that i can google to get more info on this?

Offline Mads Barnkob

  • Administrator
  • High Voltage Senior
  • *****
  • Posts: 926
  • Karma: +11/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Royer induction heater based on kaizerpowerelectronics
« Reply #5 on: June 01, 2018, 03:10:22 PM »
The Royer induction heater is self contained. The switching is done automatically based on the capacitance and the inductor value of the LC tank. If you use a microcontroller to force a non-optimal frequency I suspect something might break or at least get hot. And this circuit gets plenty hot as it is, trust me ;)

thank you sir for this information. can you elaborate more about the automatic switching? or is there some terms or reference that i can google to get more info on this?

It is a very commonly used circuit and old, the Royer oscillator: https://en.wikipedia.org/wiki/Royer_oscillator

If you want to build a IH with active gate drive, you should look into the LCLR type of inverters. These are generally also more stable and has higher power output than a Royer. The Royer IH is however very simple, fast to build but on the other hand it can also destroy itself in seconds :)
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

High Voltage Forum

Re: Royer induction heater based on kaizerpowerelectronics
« Reply #5 on: June 01, 2018, 03:10:22 PM »

 


* Recent Topics and Posts

post Re: WTS [EU]: UD2.7 thru hole pcb
[Sell / Buy / Trade]
FilipŠebík
Today at 08:39:46 AM
post Re: UD 2.7C Build
[Dual Resonant Solid State Tesla coils]
Thunderstruck
Today at 08:35:33 AM
post Re: Chinese MOSFETS/IGBTS
[Solid state Tesla coils]
flyrod
Today at 04:07:24 AM
post Re: Chinese MOSFETS/IGBTS
[Solid state Tesla coils]
Thunderstruck
March 23, 2019, 10:07:54 PM
post Re: WTS [EU]: UD2.7 thru hole pcb
[Sell / Buy / Trade]
Mads Barnkob
March 23, 2019, 04:07:55 PM
post WTS [EU]: UD2.7 thru hole pcb
[Sell / Buy / Trade]
Fumeaux
March 23, 2019, 02:12:48 PM
post Re: UD 2.7C Build
[Dual Resonant Solid State Tesla coils]
Thunderstruck
March 23, 2019, 08:03:58 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
March 23, 2019, 01:50:47 AM
post Re: Chinese MOSFETS/IGBTS
[Solid state Tesla coils]
Hydron
March 23, 2019, 12:11:10 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
badpeter
March 22, 2019, 08:19:21 PM
post Re: Chinese MOSFETS/IGBTS
[Solid state Tesla coils]
profdc9
March 22, 2019, 06:39:37 PM
post Chinese MOSFETS/IGBTS
[Solid state Tesla coils]
Fumeaux
March 22, 2019, 05:51:55 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
March 22, 2019, 03:46:16 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
kamelryttarn
March 22, 2019, 11:25:19 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
Mads Barnkob
March 22, 2019, 10:56:16 AM
post Re: looking for PCB creating software
[Printed Circuit Board]
Teravolt
March 22, 2019, 06:02:15 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
badpeter
March 21, 2019, 11:04:48 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
Hydron
March 21, 2019, 07:51:23 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
badpeter
March 21, 2019, 07:09:05 PM
post Re: looking for PCB creating software
[Printed Circuit Board]
kamelryttarn
March 21, 2019, 02:26:09 PM
post Re: GDT Experiments
[Solid state Tesla coils]
Uspring
March 21, 2019, 11:57:53 AM
post Re: GDT Experiments
[Solid state Tesla coils]
Teravolt
March 20, 2019, 11:15:50 PM
post Re: GDT Experiments
[Solid state Tesla coils]
Thunderstruck
March 20, 2019, 09:07:04 PM
post Re: Keep or throw away ?
[Beginners]
Teravolt
March 20, 2019, 05:18:07 PM
post Re: New small SSTC
[Solid state Tesla coils]
Bambinz
March 20, 2019, 03:52:15 PM
post Re: New small SSTC
[Solid state Tesla coils]
Mads Barnkob
March 20, 2019, 01:23:52 PM
post Re: GDT Experiments
[Solid state Tesla coils]
T3sl4co1l
March 20, 2019, 01:18:29 PM
post Re: GDT Experiments
[Solid state Tesla coils]
Mads Barnkob
March 20, 2019, 01:06:24 PM
post Re: cute-qcw Tesla Coil
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
March 20, 2019, 01:00:46 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
Mads Barnkob
March 20, 2019, 12:41:22 PM
post Re: Keep or throw away ?
[Beginners]
Thunderstruck
March 19, 2019, 10:02:41 PM
post Re: Keep or throw away ?
[Beginners]
Hydron
March 19, 2019, 08:14:33 PM
post Re: Keep or throw away ?
[Beginners]
Teravolt
March 19, 2019, 05:12:03 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Experimentonomen
March 19, 2019, 01:32:32 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Mads Barnkob
March 19, 2019, 12:20:34 PM
post Re: Strange gdt waveforms
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
March 19, 2019, 12:15:22 PM
post Re: Which varnish to use to coat the Secondary?
[Solid state Tesla coils]
Mads Barnkob
March 19, 2019, 10:46:50 AM
post Re: Keep or throw away ?
[Beginners]
Thunderstruck
March 19, 2019, 09:11:09 AM
post Re: Keep or throw away ?
[Beginners]
Mads Barnkob
March 19, 2019, 08:24:31 AM
post Re: Keep or throw away ?
[Beginners]
Teravolt
March 19, 2019, 01:51:51 AM
post Re: Keep or throw away ?
[Beginners]
Thunderstruck
March 18, 2019, 09:56:42 PM
post Re: cute-qcw Tesla Coil
[Dual Resonant Solid State Tesla coils]
Weston
March 18, 2019, 07:55:52 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
March 18, 2019, 06:11:07 PM
post Re: Strange gdt waveforms
[Dual Resonant Solid State Tesla coils]
Hydron
March 18, 2019, 02:27:35 PM
post Re: cute-qcw Tesla Coil
[Dual Resonant Solid State Tesla coils]
Uspring
March 18, 2019, 12:52:35 PM
post Re: Strange gdt waveforms
[Dual Resonant Solid State Tesla coils]
FilipŠebík
March 18, 2019, 12:22:58 PM
post New small SSTC
[Solid state Tesla coils]
Bambinz
March 18, 2019, 11:46:18 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
Bambinz
March 18, 2019, 11:29:02 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
Mads Barnkob
March 18, 2019, 10:35:04 AM
post Re: Strange gdt waveforms
[Dual Resonant Solid State Tesla coils]
Marty
March 18, 2019, 05:32:43 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30