Author Topic: looking for PCB creating software  (Read 1816 times)

Offline Teravolt

  • High Voltage Experimenter
  • **
  • Posts: 92
  • Karma: +1/-0
    • View Profile
looking for PCB creating software
« on: May 15, 2018, 06:27:30 PM »
I am hopping some one can help me, I have been using expressPCB but there boards are expensive. before I spend money on a license for eagle I am hopping some one has good ideas. I would like to use the chine's fab housed to do prototyping and be able to create gerbers. Right now I am doing hand solder prototypes witch I am fine with but it takes a lot time. Any advice would be appreciated.




Offline profdc9

  • High Voltage Engineer
  • ****
  • Posts: 213
  • Karma: +10/-0
    • View Profile
Re: looking for PCB creating software
« Reply #1 on: May 15, 2018, 10:12:00 PM »
Look at KiCad

http://kicad-pcb.org/

It's free and what I used to make the PCBs in the DRSSTC pack.  It's autorouting is limited, but for simple projects it works just fine.

Dan

Offline Mads Barnkob

  • Administrator
  • High Voltage Senior
  • *****
  • Posts: 989
  • Karma: +15/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: looking for PCB creating software
« Reply #2 on: May 16, 2018, 10:14:10 AM »
I also used expressPCB for the last 10 years, simply because its so easy, but ordering boards from anyone than expressPCB is not possible, I even tried to some file converter programs to get gerber files, but it did not work to an extend I was satisfied with, still a lot of manual work to correct afterwards.

So I also started using kicad, takes a while to learn and I am still a rookie at it :)
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline Teravolt

  • High Voltage Experimenter
  • **
  • Posts: 92
  • Karma: +1/-0
    • View Profile
Re: looking for PCB creating software
« Reply #3 on: May 16, 2018, 03:33:18 PM »
thanks profdc9 I down loaded Kicad and there is a little bit of learning curve I just need to find the time. like Mads I have been using express pcb for  years because it is easy I am also trying express pcb Plus. I am also trying to use the free low cut version of Eagle 9.0.1 witch also has a bit of a learning curve but I read on the net that you can get Gerbers from eagle that houses like 4pcb will accept. there is a procedure for doing that. the hook about express pcb is that it is very user friendly among other things.

Offline oneKone

  • High Voltage Engineer
  • ****
  • Posts: 249
  • Karma: +5/-0
    • View Profile
Re: looking for PCB creating software
« Reply #4 on: May 16, 2018, 03:50:12 PM »
I've used easyeda for a few simple circuits, it's web-based but it gets the job done. In all honesty I think I might go with profdc9 recommendation and try kicad

Offline profdc9

  • High Voltage Engineer
  • ****
  • Posts: 213
  • Karma: +10/-0
    • View Profile
Re: looking for PCB creating software
« Reply #5 on: May 16, 2018, 04:16:24 PM »
It's true that there's a little bit of a learning curve with Kicad, though its not too bad.  It's open source though, so at least you'll be assured you can continue to use it once you put the time into learning it.

Dan

Offline Teravolt

  • High Voltage Experimenter
  • **
  • Posts: 92
  • Karma: +1/-0
    • View Profile
Re: looking for PCB creating software
« Reply #6 on: May 16, 2018, 08:45:21 PM »

Offline flyrod

  • High Voltage Enthusiast
  • *
  • Posts: 20
  • Karma: +0/-0
    • View Profile
Re: looking for PCB creating software
« Reply #7 on: May 21, 2018, 01:49:12 PM »
Check out oshpark:

http://docs.oshpark.com/services/

Using a crippled/free version of eagle, I drew up what a wanted.  Then I uploaded the file to oshpark and a few days later I received 3 nice boards in the mail.



I've done this a few different times now and it's pretty amazing to me that it's so easy to get custom made boards for prototyping.

Offline Teravolt

  • High Voltage Experimenter
  • **
  • Posts: 92
  • Karma: +1/-0
    • View Profile
Re: looking for PCB creating software
« Reply #8 on: May 21, 2018, 06:26:03 PM »
Thanks flyrod, for the recommendation, the prices look good. I will look into eagle as well I just need give them a test drive. It is hard to get into it when I have a couple of projects going on but I will endeavor. designspark looks good to and it is widely supported by places like sparkfun.

Offline MattyLada

  • High Voltage Enthusiast
  • *
  • Posts: 1
  • Karma: +0/-0
    • View Profile
Re: looking for PCB creating software
« Reply #9 on: July 03, 2018, 06:14:05 PM »
Hi..as per my knowledge DesignSparkPCB has just about all of the chips that RS Components sells in it plus easy to make your own components. Any size board and any number of pins or pages can be used too. Don't know the layer limit off hand. Plus Gerber files too.

quick-turn pcb assembly
« Last Edit: August 02, 2018, 10:52:49 PM by MattyLada »

Offline Teravolt

  • High Voltage Experimenter
  • **
  • Posts: 92
  • Karma: +1/-0
    • View Profile
Re: looking for PCB creating software
« Reply #10 on: July 06, 2018, 06:13:33 AM »
thanks Flyrod how much were your PCB's if I might ask and how many SQ in. I think that 100$ isn't to bad for a license for eagle. are you using the free download and have you tried any others


Offline flyrod

  • High Voltage Enthusiast
  • *
  • Posts: 20
  • Karma: +0/-0
    • View Profile
Re: looking for PCB creating software
« Reply #11 on: July 07, 2018, 06:00:01 AM »
My boards so far have just been gate drive circuits with all the large components off-board.  So they're around $1 each to my mailbox.

I'm using a version of eagle for macOS.  There are newer versions available, but the one I have works for what I needed.  I think it has a limit on how big a board you can draw without paying.  I can just upload the eagle file straight to the ohspark web site to order boards.

Offline Teravolt

  • High Voltage Experimenter
  • **
  • Posts: 92
  • Karma: +1/-0
    • View Profile
Re: looking for PCB creating software
« Reply #12 on: July 08, 2018, 06:57:35 PM »
thanks I will give it a try

Offline station240

  • High Voltage Enthusiast
  • *
  • Posts: 7
  • Karma: +1/-0
    • View Profile
Re: looking for PCB creating software
« Reply #13 on: October 16, 2018, 01:56:34 PM »
has anybody tried designspark

https://www.rs-online.com/designspark/pcb-software

Been using DesignSpark for about a year now, as a replacement for Eagle after the buy out broke a lot of my libraries.
Use it with Library Loader, which is part component database website, part conversion software.

Free + no limitations for what I'm doing with it.

One neat trick I only just found, you can copy paste whole PCB designs between projects. So no need for panelization software.

Offline kamelryttarn

  • High Voltage Experimenter
  • **
  • Posts: 97
  • Karma: +0/-0
    • View Profile
Re: looking for PCB creating software
« Reply #14 on: March 21, 2019, 02:26:09 PM »
I just gave DesignSpark a try following the need to make an arduino proto shield but I can't for the life of me figure out how the program works. I find it close to impossible that I am the first/only one that need to design an arduino shield and that there are no templates I can use???

Offline Teravolt

  • High Voltage Experimenter
  • **
  • Posts: 92
  • Karma: +1/-0
    • View Profile
Re: looking for PCB creating software
« Reply #15 on: March 22, 2019, 06:02:15 AM »
I have also found it to not be straight forward. there are some YouTube videos on how to set it up. I just have not got around to it.  let me know how far you get with YouTube. Most of these programs require a leaning curve. you may also want to try eagle

Offline L_Mangold

  • High Voltage Enthusiast
  • *
  • Posts: 5
  • Karma: +0/-0
    • View Profile
Re: looking for PCB creating software
« Reply #16 on: April 29, 2019, 11:48:59 PM »
I wanted to try using Eagle, but I foolishly bought a google laptop to save money and I don't plan on buying a new PC laptop anytime soon. I was using easyEDA, but there are some glitchy aspects to it that are not very intuitive or easily solved by referencing the tutorial, some I'm thinking of trying something else that is also compatible with ChromeOS.

High Voltage Forum

Re: looking for PCB creating software
« Reply #16 on: April 29, 2019, 11:48:59 PM »

 


* Recent Topics and Posts

post Easy access to optimal resonance frequency but the benefit is quite small
[Dual Resonant Solid State Tesla coils]
VNTC
May 21, 2019, 11:35:57 PM
post Re: Offgrid 48V solar to 24V battery setup
[Electronic circuits]
Mads Barnkob
May 21, 2019, 09:59:54 PM
post Re: General Oscilloscope Probing Techniques for (DR)SSTC h-bridge
[Beginners]
Mads Barnkob
May 21, 2019, 09:51:27 PM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
T3sl4co1l
May 21, 2019, 09:49:03 PM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
82026
May 21, 2019, 09:02:10 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Vaclav
May 21, 2019, 08:59:57 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
May 21, 2019, 08:28:43 PM
post Re: Identification of unknown embedded computer, help needed.
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Mads Barnkob
May 21, 2019, 08:22:28 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Vaclav
May 21, 2019, 06:21:37 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
May 21, 2019, 06:12:55 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
profdc9
May 21, 2019, 04:06:38 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Vaclav
May 21, 2019, 03:56:56 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Vaclav
May 21, 2019, 03:46:56 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
profdc9
May 21, 2019, 02:32:59 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
May 21, 2019, 06:12:18 AM
post Re: Offgrid 48V solar to 24V battery setup
[Electronic circuits]
profdc9
May 20, 2019, 11:30:34 PM
post DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Vaclav
May 20, 2019, 06:38:54 PM
post Re: General Oscilloscope Probing Techniques for (DR)SSTC h-bridge
[Beginners]
Teravolt
May 20, 2019, 06:33:49 PM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
82026
May 20, 2019, 02:27:59 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
hightemp1
May 20, 2019, 02:57:46 AM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
T3sl4co1l
May 20, 2019, 01:06:27 AM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
82026
May 19, 2019, 09:14:59 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
May 19, 2019, 06:40:41 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
flyrod
May 19, 2019, 04:04:12 PM
post Re: Offgrid 48V solar to 24V battery setup
[Electronic circuits]
Mads Barnkob
May 19, 2019, 11:24:46 AM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
flyrod
May 19, 2019, 03:22:54 AM
post Re: Are bleeder resistors necessary if I can easily discharge my capacitor?
[Spark gap Tesla coils]
profdc9
May 19, 2019, 03:18:52 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
May 18, 2019, 10:48:59 PM
post Re: Is one of these good?
[Dual Resonant Solid State Tesla coils]
Golddustpeak
May 18, 2019, 04:19:11 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
May 17, 2019, 10:57:17 PM
post Are bleeder resistors necessary if I can easily discharge my capacitor?
[Spark gap Tesla coils]
jpb133
May 17, 2019, 09:41:56 PM
post Re: Is one of these good?
[Dual Resonant Solid State Tesla coils]
Uspring
May 17, 2019, 12:41:17 PM
post ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
82026
May 16, 2019, 04:15:58 PM
post Re: Identification of unknown embedded computer, help needed.
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Fumeaux
May 16, 2019, 02:19:39 PM
post Re: Is one of these good?
[Dual Resonant Solid State Tesla coils]
Golddustpeak
May 16, 2019, 01:50:44 PM
post Re: Is one of these good?
[Dual Resonant Solid State Tesla coils]
Uspring
May 16, 2019, 12:17:01 PM
post Re: Identification of unknown embedded computer, help needed.
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Fumeaux
May 16, 2019, 08:45:15 AM
post Re: Identification of unknown embedded computer, help needed.
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Mads Barnkob
May 15, 2019, 11:49:59 PM
post Re: Identification of unknown embedded computer, help needed.
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Hydron
May 15, 2019, 10:51:33 PM
post Identification of unknown embedded computer, help needed.
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Mads Barnkob
May 15, 2019, 09:35:41 PM
post Re: Is one of these good?
[Dual Resonant Solid State Tesla coils]
Golddustpeak
May 15, 2019, 05:07:20 PM
post Re: Mounting LCD CFL's around DRSSTC?
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
May 15, 2019, 12:46:33 PM
post Re: General Oscilloscope Probing Techniques for (DR)SSTC h-bridge
[Beginners]
Mads Barnkob
May 15, 2019, 10:08:11 AM
post Re: Is one of these good?
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
May 15, 2019, 10:04:59 AM
post General Oscilloscope Probing Techniques for (DR)SSTC h-bridge
[Beginners]
L_Mangold
May 15, 2019, 12:42:46 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
hightemp1
May 14, 2019, 11:28:43 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
badpeter
May 14, 2019, 09:58:28 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
hightemp1
May 14, 2019, 08:35:28 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
badpeter
May 14, 2019, 07:41:48 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
hightemp1
May 14, 2019, 06:05:25 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30