Author Topic: Le Koo Cee Dubloo  (Read 5595 times)

Offline Uspring

  • High Voltage Technician
  • ***
  • Posts: 172
  • Karma: +12/-0
  • Physicist
    • View Profile
Re: Le Koo Cee Dubloo
« Reply #20 on: April 24, 2018, 12:52:40 PM »
@Teravolt:
The frequency, the DRSSTC runs on, is determined by the zero current switching condition on the primary tank. The frequencies at which this happens never really match the secondary resonance frequency. If you're outside the resonance, it is often better not to have a too large Q.

@Hydron:
From the diagram you show, it looks like the lower pole is at 225kHz and the upper pole at 360kHz. The Z peak at 245kHz corresponds AFAIK to the secondary resonance. I'm wondering about your statement of secondary res being around 300kHz. It looks like primary fres could be about 300kHz as you state.

Upper pole operation is no surprise under this condition, since during the initial phase of primary rampup there is little current in the secondary, which could affect the primary. So it will start at the primary res frequency. When secondary current picks up, the coupling takes effect and the operating frequency moves up to the upper pole. I believe, that startup at the primary fres is generally the case unless special precautions are taken in order to start at a different frequency (e.g. a PLL).

But: Upper pole operation has an advantage over lower pole operation only if the primary fres is below secondary fres. And it should stay that way even under arc loading. I've illustrated this here: https://highvoltageforum.net/index.php?topic=78.msg624#msg624
If primary fres gets over secondary fres, the upper pole, at which the coil is running, will be pushed away by the coupling from secondary fres. That will impede power transfer to the secondary. Have a look at the paragraph "Tuning Tricks" in Loneoceans QCW 1.5 writeup. http://www.loneoceans.com/labs/qcw15/



Offline Hydron

  • Administrator
  • High Voltage Engineer
  • *****
  • Posts: 325
  • Karma: +11/-0
    • View Profile
Re: Le Koo Cee Dubloo
« Reply #21 on: April 24, 2018, 01:08:45 PM »
I should have included a couple of other measurements in my post as well, namely the primary (alone) and secondary+topload (alone) sweeps corresponding to the configuration in the previous graph. The primary is maybe not as far below the secondary frequency as is ideal, but I ran out of copper tubing about a turn earlier than expected when constructing it.

I've included a pic of the coil as-measured. It has changed a little since these sweeps (mostly due do a new topload), but I can do some new ones if it is of interest, this time with a log axis for impedance as well.

Offline TDAF

  • High Voltage Technician
  • ***
  • Posts: 108
  • Karma: +4/-0
    • View Profile
Re: Le Koo Cee Dubloo
« Reply #22 on: April 24, 2018, 05:42:20 PM »
Now for the inverter IGBTS
I have narrowed it down to two
IRGP50B60
And fgh60n60smd
Now irgp has very low rose and fall times but at the same time costs twice of 60n60
So, is the lower losses worth it?
Also, could yall suggest something better IGBT if any

Offline Hydron

  • Administrator
  • High Voltage Engineer
  • *****
  • Posts: 325
  • Karma: +11/-0
    • View Profile
Re: Le Koo Cee Dubloo
« Reply #23 on: April 24, 2018, 06:32:18 PM »
Price, low thermal impedance and past success all suggest going for the 60N60 (or the equivalent FGA60N65SMD if cheaper). FGY75N60SMD is also an option for slightly higher current (I have a thread about some very cheap ones I got from aliexpress).

Offline TDAF

  • High Voltage Technician
  • ***
  • Posts: 108
  • Karma: +4/-0
    • View Profile
Re: Le Koo Cee Dubloo
« Reply #24 on: April 24, 2018, 06:34:09 PM »
Price, low thermal impedance and past success all suggest going for the 60N60 (or the equivalent FGA60N65SMD if cheaper). FGY75N60SMD is also an option for slightly higher current (I have a thread about some very cheap ones I got from aliexpress).
hmm...i see

Offline Uspring

  • High Voltage Technician
  • ***
  • Posts: 172
  • Karma: +12/-0
  • Physicist
    • View Profile
Re: Le Koo Cee Dubloo
« Reply #25 on: April 25, 2018, 12:26:05 PM »
@Hydron:
Your measurements all look fine for themselves. I just can't make them to fit to the coupled system measurement. Possibly its the new topload or some influence of the primary (capacitive or whatever) on your secondary alone mesurement.

Offline Hydron

  • Administrator
  • High Voltage Engineer
  • *****
  • Posts: 325
  • Karma: +11/-0
    • View Profile
Re: Le Koo Cee Dubloo
« Reply #26 on: April 25, 2018, 03:07:11 PM »
OK, yeah that is a possibility. I'll make some more measurements and document them better - those were from a few years back.

Offline TDAF

  • High Voltage Technician
  • ***
  • Posts: 108
  • Karma: +4/-0
    • View Profile
Re: Le Koo Cee Dubloo
« Reply #27 on: April 25, 2018, 04:30:01 PM »
Using the formulas off of Richie burnett''s website
My coil will have the upper pole at around 500-520khz
Doesn't that seem too high?
How will the coil ever get around to achieving upper pole operation?

Also, how can one use a startup oscillator with a ud2.7
I'm looking forward to using Steve ward''s tuning trick for QCWs

Offline TDAF

  • High Voltage Technician
  • ***
  • Posts: 108
  • Karma: +4/-0
    • View Profile
Re: Le Koo Cee Dubloo
« Reply #28 on: May 14, 2018, 11:06:33 AM »
So, for the MMC
Will CBB capacitors work?
I'm thinking of something like 100 caps 10 in series 10 in parallel to give about 10nf of capacitance
https://www.ebay.com/itm/10Pcs-CBB-Capacitor-100V-101-683-0-1nF-68nF-101J-683J-Pitch-5mm/192143864676?hash=item2cbcaab364:m:miP5zeN54Fp-RSicta7nMyQ
Something like these capacitors...

GUESS WHO JUST FOUND SOME DATASHEETS!!!!

looking at the datasheets even though the peak current ratings are for <100khz
the RMS ratings look quite sufficient

what do you guys think??

High Voltage Forum

Re: Le Koo Cee Dubloo
« Reply #28 on: May 14, 2018, 11:06:33 AM »

 


* Recent Topics and Posts

post Re: Dual MOT tesla coil
[Spark Gap Tesla Coils (SGTC)]
davekni
August 05, 2020, 11:48:55 PM
post Re: How much is the voltage used in Corona Discharge tubes for ozone Generation?
[Transformer (Ferrite Core)]
davekni
August 05, 2020, 11:37:13 PM
post Re: Easy to build Polyphonic MIDI Interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
AstRii
August 05, 2020, 08:01:11 PM
post Re: Fun with wireless power
[Solid State Tesla Coils (SSTC)]
Lightning On Demand
August 05, 2020, 06:34:08 PM
post Re: How much is the voltage used in Corona Discharge tubes for ozone Generation?
[Transformer (Ferrite Core)]
Uspring
August 05, 2020, 12:56:32 PM
post Re: Fun with wireless power
[Solid State Tesla Coils (SSTC)]
Mads Barnkob
August 05, 2020, 12:55:52 PM
post Re: Bipolar high voltage multiplier project - more than 70cm hot arc discharge
[Voltage Multipliers]
Teravolt
August 04, 2020, 09:21:09 PM
post Re: How much is the voltage used in Corona Discharge tubes for ozone Generation?
[Transformer (Ferrite Core)]
johnf
August 04, 2020, 09:16:55 PM
post Re: Does anyone know how this site works.
[General Chat]
thedoc298
August 04, 2020, 05:53:03 PM
post Re: Does anyone know how this site works.
[General Chat]
thedoc298
August 04, 2020, 05:51:03 PM
post Re: Fun with wireless power
[Solid State Tesla Coils (SSTC)]
Lightning On Demand
August 04, 2020, 05:17:26 PM
post Re: Fun with wireless power
[Solid State Tesla Coils (SSTC)]
Max
August 04, 2020, 02:14:56 PM
post Re: Easy to build Polyphonic MIDI Interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Max
August 04, 2020, 02:08:07 PM
post Re: Easy to build Polyphonic MIDI Interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
futurist
August 04, 2020, 10:48:35 AM
post Re: How much is the voltage used in Corona Discharge tubes for ozone Generation?
[Transformer (Ferrite Core)]
UB_Serpent
August 04, 2020, 10:02:39 AM
post Re: Dual MOT tesla coil
[Spark Gap Tesla Coils (SGTC)]
Jun
August 04, 2020, 08:47:07 AM
post Re: Dual MOT tesla coil
[Spark Gap Tesla Coils (SGTC)]
Jun
August 04, 2020, 08:43:00 AM
post Re: Does anyone know how this site works.
[General Chat]
Mads Barnkob
August 04, 2020, 08:33:47 AM
post Re: Does anyone know how this site works.
[General Chat]
MRMILSTAR
August 04, 2020, 05:09:26 AM
post Does anyone know how this site works.
[General Chat]
thedoc298
August 04, 2020, 01:54:49 AM
post Fun with wireless power
[Solid State Tesla Coils (SSTC)]
Lightning On Demand
August 03, 2020, 11:55:41 PM
post Re: Dual MOT tesla coil
[Spark Gap Tesla Coils (SGTC)]
Teravolt
August 03, 2020, 09:17:40 PM
post Re: Dual MOT tesla coil
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
August 03, 2020, 08:30:38 PM
post Re: Budget USB cameras
[High Speed Filming]
missoum0514
August 03, 2020, 06:56:08 PM
post Re: Dual MOT tesla coil
[Spark Gap Tesla Coils (SGTC)]
Jun
August 03, 2020, 05:23:15 PM
post Re: Is my xray transformer a ferrite core and how would I drive it?
[Transformer (Ferrite Core)]
nielsquake
August 03, 2020, 05:02:26 PM
post Re: Easy to build Polyphonic MIDI Interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Max
August 03, 2020, 04:31:04 PM
post Re: Easy to build Polyphonic MIDI Interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
futurist
August 03, 2020, 10:05:59 AM
post Re: Is my xray transformer a ferrite core and how would I drive it?
[Transformer (Ferrite Core)]
Mads Barnkob
August 03, 2020, 08:21:26 AM
post Re: Is my xray transformer a ferrite core and how would I drive it?
[Transformer (Ferrite Core)]
nielsquake
August 02, 2020, 11:45:38 PM
post Re: How much is the voltage used in Corona Discharge tubes for ozone Generation?
[Transformer (Ferrite Core)]
davekni
August 02, 2020, 08:10:47 PM
post Re: How much is the voltage used in Corona Discharge tubes for ozone Generation?
[Transformer (Ferrite Core)]
Uspring
August 02, 2020, 07:27:33 PM
post Re: Corona lockdown thread, tell about your situation
[General Chat]
Uspring
August 02, 2020, 07:14:17 PM
post Re: Is my xray transformer a ferrite core and how would I drive it?
[Transformer (Ferrite Core)]
nielsquake
August 02, 2020, 06:58:34 PM
post Re: current limiting to parallel resonance circuit
[Beginners]
davekni
August 02, 2020, 06:49:59 PM
post Re: Dual MOT tesla coil
[Spark Gap Tesla Coils (SGTC)]
Jun
August 02, 2020, 05:10:12 PM
post Re: Dual MOT tesla coil
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
August 02, 2020, 04:55:14 PM
post Re: How much is the voltage used in Corona Discharge tubes for ozone Generation?
[Transformer (Ferrite Core)]
UB_Serpent
August 02, 2020, 04:20:13 PM
post Re: How much is the voltage used in Corona Discharge tubes for ozone Generation?
[Transformer (Ferrite Core)]
UB_Serpent
August 02, 2020, 04:05:12 PM
post Dual MOT tesla coil
[Spark Gap Tesla Coils (SGTC)]
Jun
August 02, 2020, 01:07:54 PM
post current limiting to parallel resonance circuit
[Beginners]
plasma
August 02, 2020, 07:13:54 AM
post Re: How much is the voltage used in Corona Discharge tubes for ozone Generation?
[Transformer (Ferrite Core)]
davekni
August 02, 2020, 02:26:11 AM
post Re: FPS1000HD unboxing and first impression
[High Speed Filming]
missoum0514
August 01, 2020, 11:57:24 PM
post Re: How much is the voltage used in Corona Discharge tubes for ozone Generation?
[Transformer (Ferrite Core)]
TMaxElectronics
August 01, 2020, 10:24:21 PM
post Re: How much is the voltage used in Corona Discharge tubes for ozone Generation?
[Transformer (Ferrite Core)]
klugesmith
August 01, 2020, 03:59:43 PM
post Re: How much is the voltage used in Corona Discharge tubes for ozone Generation?
[Transformer (Ferrite Core)]
UB_Serpent
August 01, 2020, 06:22:53 AM
post Re: Is my xray transformer a ferrite core and how would I drive it?
[Transformer (Ferrite Core)]
nielsquake
July 31, 2020, 07:32:09 PM
post Re: Is my xray transformer a ferrite core and how would I drive it?
[Transformer (Ferrite Core)]
nielsquake
July 31, 2020, 06:15:27 PM
post Re: Is my xray transformer a ferrite core and how would I drive it?
[Transformer (Ferrite Core)]
nielsquake
July 31, 2020, 05:38:49 PM
post Re: Corona lockdown thread, tell about your situation
[General Chat]
klugesmith
July 31, 2020, 04:35:43 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal