Author Topic: Drsstc 3  (Read 7844 times)

Offline Netzpfuscher

  • High Voltage Experimenter
  • **
  • Posts: 84
  • Karma: +4/-0
    • View Profile
Re: Drsstc 3
« Reply #60 on: August 19, 2019, 07:37:07 AM »
I strongly suggest to use active cooling on the bridge. I calculated the numbers for my SKM400 coil. At 16% dutycycle with 1000A peak I have around 500W power dissipation.
The cooler you start your burst the more headroom you have to the max junction temperature.

That's the reason why my new coil has a big heat sink and a strong cooling fan. 

Online Hydron

  • Administrator
  • High Voltage Engineer
  • *****
  • Posts: 256
  • Karma: +8/-0
    • View Profile
Re: Drsstc 3
« Reply #61 on: August 19, 2019, 10:44:35 AM »
16% duty cycle is really high, is this with pulse-skipping and very long on-time?

As for the OP's bridge rectifier going pop, was it due to the streamer hit to the primary?
Commonly accepted practice is to tie one side of the DC bus to earth via a moderate value capacitor (e.g. 100nf), so that any current from a streamer strike has a low-impedance path to earth from the primary. The theory is that if this low-Z path is not present then you may run the risk of internal breakdown of the IGBTs or diode bridge to the earthed heatsink they are mounted to. Not sure how tested it is other than Steve Ward removing his strike ring and encouraging arcs to hit the primary of one of his coils (without any damage), but it does make sense as a theory!

Offline Netzpfuscher

  • High Voltage Experimenter
  • **
  • Posts: 84
  • Karma: +4/-0
    • View Profile
Re: Drsstc 3
« Reply #62 on: August 19, 2019, 02:27:06 PM »
Yes 16% is with pulse skipping and for SID files with 4 simultaneous voices. With this numbers I wanted to indicate that there is a fair amount of dissipation in a DRSSTC even at lower duty cycles.

The capacitor solution is a problem with RCDs, the high frequency ripple on the bus drives a current through the capacitor and this trips the RCD. I suggest to use two strings of TVS diodes from the inverter output to earth.  (6x 100V 1,5kW)

Offline oneKone

  • High Voltage Engineer
  • ****
  • Posts: 274
  • Karma: +6/-0
    • View Profile
Re: Drsstc 3
« Reply #63 on: August 21, 2019, 03:59:47 AM »
Cheers for the nudge to go active cooling @Netzpfuscher, I'll implement it when I replace the rectifier.

@Hydron the primary strike wasn't what killed the rectifier but I think it could have weakened/damaged it somehow, the failed when a greater input current was used.

« Last Edit: August 22, 2019, 09:32:17 PM by Mads Barnkob »

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1118
  • Karma: +17/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Drsstc 3
« Reply #64 on: August 22, 2019, 09:32:24 PM »
Even a electrostatic discharge can weaken a silicon-based component, so you could have a internal failure where the insulating layer between the copper base plate of the rectifier and its silicon die was broken down through a micro channel. Just a single small flash through and some burned goo or plastic and its done :(
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline oneKone

  • High Voltage Engineer
  • ****
  • Posts: 274
  • Karma: +6/-0
    • View Profile
Re: Drsstc 3
« Reply #65 on: August 29, 2019, 12:54:28 AM »
With the toroid on my mind I set out to fix it. I tried bending each segment more to achieve a tighter radius but I still had sharp edges, to fix this I added copper rings to the top and bottom to cover them... And boy did it work! I'm getting almost 2m streamers now. There's still a bit of leakage but I think with a Polish and a coat of polyurethane it will fix the problem. I also think I might have the secondary too close to the primary, most of the time a ground strike is met with an arc from the bottom of the secondary to the primary. The first video is without the rings, the second video is with the rings.
/>
/>

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1118
  • Karma: +17/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Drsstc 3
« Reply #66 on: August 30, 2019, 09:30:23 AM »
Good that you see improvements! I watched the whole MIDI video, good stuff :)

Your coupling is too high or it is badly tuned when you get racing sparks, it can also be a insufficient grounding of the secondary coil.

I am actually not sure if varnishing the topload is a good idea, will it disrupt the electron charge and the toploads ability to have a surface capacitance, anyone can answer this?
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline Uspring

  • High Voltage Technician
  • ***
  • Posts: 108
  • Karma: +8/-0
    • View Profile
Re: Drsstc 3
« Reply #67 on: September 02, 2019, 12:09:49 PM »
Quote
I am actually not sure if varnishing the topload is a good idea, will it disrupt the electron charge and the toploads ability to have a surface capacitance, anyone can answer this?

The varnish will have two properties. It will be a dielelectric and an insulator. As a dielelectric it will be polarised, causing an electric field opposite to that of the top load. Since it is a volume effect and the varnish probably thin, there will be a negligible increase of top load capacitance.

As an insulator, the varnish won't stop the appearance of an electric field around a charged up top load. Near points of high curvature, ionisation of the air will occur. If the top load is say, at a high positive voltage, the free electrons created will be attracted to and stick to the varnish and generate an electric field opposite to that of the top load. Eventually, this will stifle the ionisation.
But once the top load voltage reverses, the stuck electrons will increase the field and ionisation will start again. This time positive ions will stick to the varnish. So you will have some ionisation on each cycle.

Another way to see this is, that the varnish will act as an insulator of a capacitor, insulating the top load from a more or less conducting volume of air around it. And a capacitor is an AC conductor. The appearance of racing sparks along secondaries and primary secondary flash overs illustrate, that high frequency voltages don't really care about insulators. But they do help somewhat.

The long breakout rod you use is certainly a good idea. The breakout from there reduces the top load voltages. But the best option is to avoid sharp edges.

Offline oneKone

  • High Voltage Engineer
  • ****
  • Posts: 274
  • Karma: +6/-0
    • View Profile
Re: Drsstc 3
« Reply #68 on: September 03, 2019, 07:27:17 AM »
Cheers for the info guys. I'll polish the top load and mess around with the tuning, I might even make some discs to lower the coupling if need be.

As it stands time is running out in this coil for the year, as summer approaches the days get longer so I won't be able to run the coil 😓

High Voltage Forum

Re: Drsstc 3
« Reply #68 on: September 03, 2019, 07:27:17 AM »

 


* Recent Topics and Posts

post Re: Problems with my first DRSSTC
[Dual Resonant Solid State Tesla coils]
Phoenix
Today at 07:37:55 AM
post Re: Large Ferrite Core with IGBT-Brick Driver
[Transformer (ferrite core)]
Phoenix
Today at 06:43:39 AM
post Re: Problems with my first DRSSTC
[Dual Resonant Solid State Tesla coils]
davekni
Today at 01:45:37 AM
post Re: Breakout rod material and size vs streamer resuls
[Dual Resonant Solid State Tesla coils]
davekni
Today at 12:18:00 AM
post Re: My DRSSTC does not want to resonate at correct frequency
[Dual Resonant Solid State Tesla coils]
davekni
September 22, 2019, 10:16:26 PM
post Re: My DRSSTC does not want to resonate at correct frequency
[Dual Resonant Solid State Tesla coils]
AstRii
September 22, 2019, 05:40:52 PM
post Re: My DRSSTC does not want to resonate at correct frequency
[Dual Resonant Solid State Tesla coils]
davekni
September 22, 2019, 06:43:46 AM
post Re: My DRSSTC does not want to resonate at correct frequency
[Dual Resonant Solid State Tesla coils]
AstRii
September 22, 2019, 12:36:23 AM
post Re: My DRSSTC does not want to resonate at correct frequency
[Dual Resonant Solid State Tesla coils]
Hydron
September 22, 2019, 12:03:43 AM
post My DRSSTC does not want to resonate at correct frequency
[Dual Resonant Solid State Tesla coils]
AstRii
September 21, 2019, 09:01:48 PM
post Re: The new toy
[Laboratories ]
DashApple
September 21, 2019, 05:54:03 PM
post Re: The new toy
[Laboratories ]
MRMILSTAR
September 21, 2019, 05:38:14 PM
post Re: The new toy
[Laboratories ]
DashApple
September 21, 2019, 04:55:44 PM
post Re: The new toy
[Laboratories ]
MRMILSTAR
September 21, 2019, 04:03:48 PM
post Re: The new toy
[Laboratories ]
T3sl4co1l
September 21, 2019, 03:57:22 PM
post Re: The new toy
[Laboratories ]
Hydron
September 21, 2019, 09:15:47 AM
post Re: The new toy
[Laboratories ]
Hydron
September 21, 2019, 09:11:18 AM
post Re: The new toy
[Laboratories ]
AlexanderHun
September 21, 2019, 09:08:50 AM
post Re: The new toy
[Laboratories ]
AlexanderHun
September 21, 2019, 08:59:41 AM
post Re: Blast from the past!
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Hydron
September 20, 2019, 11:32:35 PM
post Re: Help choosing a Hantek USB oscilloscope
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Hydron
September 20, 2019, 11:28:05 PM
post Re: The new toy
[Laboratories ]
Hydron
September 20, 2019, 11:20:21 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
Hydron
September 20, 2019, 11:10:54 PM
post Re: The new toy
[Laboratories ]
AlexanderHun
September 20, 2019, 09:49:00 PM
post Re: The new toy
[Laboratories ]
DashApple
September 20, 2019, 08:17:36 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
September 20, 2019, 08:06:32 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
September 20, 2019, 05:43:13 PM
post Re: Help choosing a Hantek USB oscilloscope
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Twospoons
September 20, 2019, 01:32:30 PM
post Re: Adventures in induction heating
[Electronic circuits]
Coyote
September 20, 2019, 10:56:19 AM
post Re: Help choosing a Hantek USB oscilloscope
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
kamelryttarn
September 20, 2019, 10:02:28 AM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
davekni
September 20, 2019, 07:05:19 AM
post Re: Help choosing a Hantek USB oscilloscope
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Hydron
September 19, 2019, 11:16:21 PM
post Re: The new toy
[Laboratories ]
AlexanderHun
September 19, 2019, 09:49:30 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
September 19, 2019, 09:49:15 PM
post Re: The new toy
[Laboratories ]
Mads Barnkob
September 19, 2019, 09:13:29 PM
post Re: Help choosing a Hantek USB oscilloscope
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Mads Barnkob
September 19, 2019, 09:08:20 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
September 19, 2019, 07:16:20 PM
post Help choosing a Hantek USB oscilloscope
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
kamelryttarn
September 19, 2019, 04:19:58 PM
post The new toy
[Laboratories ]
AlexanderHun
September 19, 2019, 09:01:46 AM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
September 18, 2019, 07:27:46 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
September 18, 2019, 06:56:20 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
September 18, 2019, 05:08:06 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
September 18, 2019, 01:35:58 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
September 18, 2019, 05:54:23 AM
post Re: Blast from the past!
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
klugesmith
September 18, 2019, 05:05:55 AM
post Re: UD2.7 Gate Signals
[Dual Resonant Solid State Tesla coils]
coilinator
September 17, 2019, 08:24:59 PM
post Re: Blast from the past!
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
MRMILSTAR
September 17, 2019, 08:19:45 PM
post Re: Blast from the past!
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Mads Barnkob
September 17, 2019, 06:53:52 PM
post Blast from the past!
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
MRMILSTAR
September 17, 2019, 05:52:00 PM
post Re: CM300 coil build questions
[Dual Resonant Solid State Tesla coils]
acobaugh
September 17, 2019, 05:00:47 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30