Author Topic: Best core for GDT and FBT  (Read 3012 times)

Offline FilipŠebík

  • High Voltage Enthusiast
  • *
  • Posts: 34
  • Karma: +1/-0
    • View Profile
Best core for GDT and FBT
« on: January 09, 2018, 03:47:39 PM »
Hey, today I took my SSTC driver to school and probed the GDT on oscilloscope. The things I saw... I can't even explain how horrible the waveform looked. I just though that the bad performance of my driver would be caused by my interrupter, which I probed too and its very good looking.

GDT: So to the core type. As far as I've searched, I found this https://www.tme.eu/gb/details/tx42_26-3e25/ring-ferrites/ferroxcube/tx422613-3e25/
Nothing more. I know its against the rules, but if someone wants to take their time, they can find a core on this page https://www.tme.eu/gb/katalog/ring-ferrites_113555/ Where I can buy stuff from and this would be useful for everyone that is looking for a good core.

FBT: I found this https://www.tme.eu/gb/details/ppas100/current-transformers/talema/as-100/ I don't know if 1:50 ratio is good for FBT, but as I've seen on many schematics that they use 1:50 ratio, I though that it should be good. If it would be better to wind my own FBT, then this one? https://www.tme.eu/gb/details/tx42_26-3e25/ring-ferrites/ferroxcube/tx422613-3e25/ :DDD I know I posted this one for the GDT, but I think that its ok too :D

Thanks for help

Offline Laci

  • High Voltage Engineer
  • ****
  • Posts: 213
  • Karma: +6/-0
    • View Profile
Re: Best core for GDT and FBT
« Reply #1 on: January 09, 2018, 04:26:07 PM »
I am using the TX42/26/13-3E25 cores as GDT,OCD,FBT.As GDT it works very well(150kHz),as OCD and FBT I did not tested yet.It also depends on the driver and the load.Why would you like to use FBT with primary feedback(right?!)instead of antenna or secondary base feedback?I am just interested. :)

Offline FilipŠebík

  • High Voltage Enthusiast
  • *
  • Posts: 34
  • Karma: +1/-0
    • View Profile
Re: Best core for GDT and FBT
« Reply #2 on: January 09, 2018, 04:35:02 PM »
I say, that thing that sucks the most is the antenna, so I want to replace the secondary feedback antenna with a FBT

edit:
Too bad... The TX42/26/13-3E25 core is not on stock... So I tried to find another one and I found this https://www.tme.eu/gb/details/tn25_15-3e25/ring-ferrites/ferroxcube/tn251510-3e25/ and this one https://www.tme.eu/gb/details/tn29_19-3e25/ring-ferrites/ferroxcube/tn291975-3e25/ I don't know if any of those are good or bad. This is my last resort, or maybe my GDT is wound bad? Its a yellow core from PC power supply. I wound huge amount of turns of a cat6 cable around it. I can bring the core to my school and measure it at thursday, but not earlier. I would wind less turns on it and even test some other cores that I have. I even have some flyback cores that I will use to wind my own flyback (more on that later) and I can test those too :DDDD Also I think that using flyback core is stupid but who knows :D
« Last Edit: January 09, 2018, 10:32:47 PM by Mads Barnkob »

Offline Laci

  • High Voltage Engineer
  • ****
  • Posts: 213
  • Karma: +6/-0
    • View Profile
Re: Best core for GDT and FBT
« Reply #3 on: January 09, 2018, 06:28:28 PM »
The yellow core from the PC PSU is really bad for GDT,its made out of iron powder which is not good.I recommend you to check out my "SSTC (Not) Working Correctly" post.I had the same questions and got perfect answers to all of them.

https://highvoltageforum.net/index.php?topic=122.0
« Last Edit: January 09, 2018, 10:32:22 PM by Mads Barnkob »

Offline oneKone

  • High Voltage Engineer
  • ****
  • Posts: 282
  • Karma: +7/-0
    • View Profile
Re: Best core for GDT and FBT
« Reply #4 on: January 10, 2018, 12:49:13 AM »
I've been using n30 cores from rs components for my gdt , they seem to work well and are relatively cheap. The one I've been using is:
  https://au.rs-online.com/mobile/p/ferrite-rings/2120982/

« Last Edit: January 10, 2018, 12:52:05 AM by oneKone »


Offline futurist

  • Global Moderator
  • High Voltage Technician
  • *****
  • Posts: 116
  • Karma: +0/-0
    • View Profile
Re: Best core for GDT and FBT
« Reply #6 on: January 10, 2018, 03:13:30 PM »
3E25 material will work fine. I use same ferroxcube cores from TME for both GDT and CTs

Offline FilipŠebík

  • High Voltage Enthusiast
  • *
  • Posts: 34
  • Karma: +1/-0
    • View Profile
Re: Best core for GDT and FBT
« Reply #7 on: January 12, 2018, 07:31:19 PM »
Nice, the cores arrived and just waiting till Tuesday, so I can test them on oscilloscope in school. Any ideas on how many windings I should use? I say about 12-15, so 13 is fine I guess. And I won't test the TN14, TN13 and TN10 because they are too small. And I will make a new thread with links for the cores, scope pictures, frequencies used as well as some other things too.

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1175
  • Karma: +17/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Best core for GDT and FBT
« Reply #8 on: January 12, 2018, 09:02:04 PM »
I flipped through my file archive and found a spreadsheet I made back in 2013 to calculate GDTs. Some day I will convert it to a online calculator, but for now you can try it out here.

It is in openoffice format, I don't know if excel can open it?
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline FilipŠebík

  • High Voltage Enthusiast
  • *
  • Posts: 34
  • Karma: +1/-0
    • View Profile
Re: Best core for GDT and FBT
« Reply #9 on: January 13, 2018, 06:57:34 AM »
Thanks for the calculator, I calculated "Something" and came up with 13 turns on the primary. Duh what a coincidence that I predicted that :D

Offline Hydron

  • Administrator
  • High Voltage Engineer
  • *****
  • Posts: 273
  • Karma: +8/-0
    • View Profile
Re: Best core for GDT and FBT
« Reply #10 on: February 02, 2018, 10:48:39 AM »
This is what I used:
http://uk.farnell.com/epcos/b64290l0674x830/ferrite-core-toroid-n30/dp/1190604?st=n30%20toroid

I could only fit 5-6 turns on in my case, so I had to find something with higher Al (this has 5.75uH).

High Voltage Forum

Re: Best core for GDT and FBT
« Reply #10 on: February 02, 2018, 10:48:39 AM »

 


* Recent Topics and Posts

post Possible use for large inductor (laminated core)
[Transformer (iron core)]
kamelryttarn
Today at 09:43:11 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
Today at 12:53:57 AM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
davekni
December 08, 2019, 09:57:51 PM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
MRMILSTAR
December 08, 2019, 05:28:09 PM
post Aethra CCD Webcam Teardown - From Back When Streaming Was Expensive!
[Electronic circuits]
Mads Barnkob
December 08, 2019, 01:33:30 PM
post Platter resistance & inductance
[Induction launchers, coil guns and rails guns]
klugesmith
December 08, 2019, 11:41:00 AM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
davekni
December 08, 2019, 06:50:11 AM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
plasma
December 08, 2019, 12:00:00 AM
post CW multiplier resistor string suggestions
[Voltage Multipliers]
MRMILSTAR
December 07, 2019, 11:32:49 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 07, 2019, 09:54:31 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 07, 2019, 09:48:21 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 07, 2019, 08:59:57 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
MRMILSTAR
December 06, 2019, 08:35:29 PM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 06, 2019, 05:19:26 AM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
davekni
December 06, 2019, 03:48:34 AM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
the_anomaly
December 06, 2019, 03:35:39 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
AstRii
December 06, 2019, 01:27:03 AM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 05, 2019, 11:38:59 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
Mads Barnkob
December 05, 2019, 07:33:01 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
sjsimmo
December 05, 2019, 11:09:20 AM
post Cost reduction in consumer electrics
[Electronic circuits]
klugesmith
December 05, 2019, 07:25:20 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 05, 2019, 05:52:11 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 05, 2019, 05:21:07 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 04, 2019, 06:05:11 PM
post Re: Full bridge showing half the voltage
[Beginners]
shrad
December 04, 2019, 02:57:02 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
Uspring
December 04, 2019, 12:40:51 PM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 04, 2019, 11:20:25 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 04, 2019, 08:28:15 AM
post Re: Full bridge showing half the voltage
[Beginners]
klugesmith
December 04, 2019, 07:41:21 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
MRMILSTAR
December 04, 2019, 05:15:49 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 04, 2019, 05:06:39 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 04, 2019, 04:31:16 AM
post Re: Full bridge showing half the voltage
[Beginners]
davekni
December 04, 2019, 04:26:38 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 04, 2019, 04:10:16 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 04, 2019, 12:28:15 AM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 04, 2019, 12:11:32 AM
post Re: HV resistor in oil
[Voltage Multipliers]
johnf
December 03, 2019, 07:58:41 PM
post Re: Driving Nixie-tubes with arduino
[Electronic circuits]
johnf
December 03, 2019, 07:54:08 PM
post Re: Full bridge showing half the voltage
[Beginners]
klugesmith
December 03, 2019, 07:41:00 PM
post Re: Driving Nixie-tubes with arduino
[Electronic circuits]
kamelryttarn
December 03, 2019, 02:14:00 PM
post Re: Driving Nixie-tubes with arduino
[Electronic circuits]
Mads Barnkob
December 03, 2019, 01:24:00 PM
post Re: Driving Nixie-tubes with arduino
[Electronic circuits]
klugesmith
December 03, 2019, 10:45:58 AM
post Driving Nixie-tubes with arduino
[Electronic circuits]
kamelryttarn
December 03, 2019, 09:04:42 AM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 03, 2019, 07:29:48 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 03, 2019, 05:07:28 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 03, 2019, 04:34:46 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 02, 2019, 09:06:07 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
T3sl4co1l
December 02, 2019, 10:51:33 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 02, 2019, 05:49:05 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
December 02, 2019, 04:10:14 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30