Author Topic: I started making a drsstc  (Read 1154 times)

Offline Miki_407

  • High Voltage Enthusiast
  • *
  • Posts: 23
  • Karma: +0/-0
    • View Profile
I started making a drsstc
« on: November 30, 2020, 11:58:29 AM »
Hello,
I am 14 years old and this is my first true drsstc. Does the secondary need to be changed? I used 0.1mm wire for it and a 75mm pvc pipe, length of windings is 14.5cm. Would it be better to make a 24cm long windings with 0.2mm wire on a 75m pvc pipe? I plan on using a full bridge with parallel 40n60n igbts. Also i wanted to ask is my topload ok, i made it myself from some copper pipe. Any later questions i have i will make in this post.

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1624
  • Karma: +29/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: I started making a drsstc
« Reply #1 on: November 30, 2020, 12:56:05 PM »
Hi Miki and welcome to HVF :)

It is great to see young people taking on the challenge of building a DRSSTC.

I calculated your tesla coil resonant frequency and you have around 1300 turns and which your topload you are properly around 130'ish kHz resonant frequency, looking at the tesla coil impedance list, you properly have a impedance higher than 60k, so you should be designing for a high impedance inverter. This means lower peak current, longer on-time and that means you should have more turns on the primary coil and a smaller MMC in order to hit high impedance in the primary circuit. You should also check out the MMC calculator to make it easier to get it right in your Tesla coil.

What are you planning to use as driver? There is a great variety of the old school universal driver 1.3b and up to the latest fully digital and PC controlled NextGen UD3
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline Miki_407

  • High Voltage Enthusiast
  • *
  • Posts: 23
  • Karma: +0/-0
    • View Profile
Re: I started making a drsstc
« Reply #2 on: November 30, 2020, 01:16:04 PM »
I am planing on using ud2.7. I have used this coil before with a smaller topload and 16 turns primary. I was afraid with this bigger topload it would arc back to primary.
This is the video of it on 300vdc. It sadly died shortly after. I think a biggest problem was phase lead as i have been using a pll circuit also long wires from bridge to primary, no snubber capacitors.

Few other questions.
1.How long sparks should i expect?
3.Should i make a primary with tap points or go with a primary simular to one shown in my video?
« Last Edit: November 30, 2020, 07:47:05 PM by Mads Barnkob »

Offline davekni

  • High Voltage Senior
  • *****
  • Posts: 869
  • Karma: +41/-0
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: I started making a drsstc
« Reply #3 on: November 30, 2020, 08:49:30 PM »
Your primary looks fine.  With it being fixed inductance, you will need some way to add and/or remove capacitance of the MMC between H-Bridge and primary coil.  That is my preference - adjusting MMC rather than primary winding.  However, tapped primary winding is much more common.  (Ferrites can be used to adjust primary frequency, but there are many complications to consider for that option.)

Arc length depends on many factors, especially enable pulse width and repetition frequency.  I've had best success with high (1kHz+) repetition with ramped pulse width.

For H-Bridge layout, I recommend copper planes as in this post:
https://highvoltageforum.net/index.php?topic=1324.0

Good luck!  Nice progress already!
David Knierim

Offline Miki_407

  • High Voltage Enthusiast
  • *
  • Posts: 23
  • Karma: +0/-0
    • View Profile
Re: I started making a drsstc
« Reply #4 on: November 30, 2020, 08:58:41 PM »
I am using a layout of loneoceans easybridge. Soon parts should arrive so i will post when i find new problem or finish it. Adjusting a mmc wont really be problem as i am using 50 capacitors(2kv 4.7nf). Thank for the help.

Offline Miki_407

  • High Voltage Enthusiast
  • *
  • Posts: 23
  • Karma: +0/-0
    • View Profile
Re: I started making a drsstc
« Reply #5 on: January 09, 2021, 03:53:25 PM »
         So a little problem has risen. I used non inverting mosfet driver UCC27424 instead of UCC27423. Will making a mod board that fits on phase control and inverts the inputs be good enough until i order replacements.

Offline davekni

  • High Voltage Senior
  • *****
  • Posts: 869
  • Karma: +41/-0
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: I started making a drsstc
« Reply #6 on: January 09, 2021, 07:42:20 PM »
Yes, inverters on those two 74HC08 outputs should work fine.  The inverters will add a bit more delay, so require slightly more phase lead to compensate.

Another option is to change the 74HC08 to a 74HC00 (AND to NAND gate).  If you do that, bypass the inverter on pin 8 of the NAND gate to keep enable logic correct (bypass 74HC14 pins 12 and 13).

For your previous concern about arcs to the primary coil, most DRSSTC designs include a strike rail near the top of the primary coil.  That's a grounded not-quite-complete turn of exposed conductor (ie. copper pipe or ...) with diameter a bit larger than outside of primary.  Any arcs that head down will hit that rail before reaching the primary.
David Knierim

Offline Miki_407

  • High Voltage Enthusiast
  • *
  • Posts: 23
  • Karma: +0/-0
    • View Profile
Re: I started making a drsstc
« Reply #7 on: January 11, 2021, 09:15:11 PM »
Finally made the mod board work :D. Turns out my first ic was broken. It isn't tuned right. Primary side is 150kHz and secondary is 185kHz with no arcs. No phase lead is set jet. I had issues with it arcing back to primary but lowering the primary fixed it. Later I might change to pancake primary.
So here is a video of it working:
 
/>

Offline davekni

  • High Voltage Senior
  • *****
  • Posts: 869
  • Karma: +41/-0
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: I started making a drsstc
« Reply #8 on: January 11, 2021, 09:41:53 PM »
Congratulations!
David Knierim

Offline Miki_407

  • High Voltage Enthusiast
  • *
  • Posts: 23
  • Karma: +0/-0
    • View Profile
Re: I started making a drsstc
« Reply #9 on: January 16, 2021, 06:38:11 PM »
I need to ask some questions.
On what amperage should I put ocd for my 2 parallel 40n60n igbt full bridge?
What is easiest way to see if I am not too far away from zero point switching? I don't have a differential probe and I only have usb oscilloscope.

Soon i will upload another video.

Offline davekni

  • High Voltage Senior
  • *****
  • Posts: 869
  • Karma: +41/-0
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: I started making a drsstc
« Reply #10 on: January 16, 2021, 07:06:13 PM »
What is the full part number for "40n60n"?  I'd need to see a datasheet in order to estimate current capability.  Also, what gate voltage are you running (in other words, what supply voltage is running to the UD2.7 board)?

Do you have a scope probe capable of measuring 340V waveforms even if not isolated?  If so, you can capture useful H-Bridge output waveforms even on top of the line-frequency base.  Of course, DO NOT CONNECT THE SCOPE PROBE GROUND TO THE H-BRIDGE BUS SUPPLY.  (However, response will improve if the scope ground is wired through a ~0.1uF 400+V capacitor to H-Bridge VBus- rail.)  Trigger on the H-Bridge output waveform, adjusting trigger threshold for the lowest (most negative) voltage that captures waveforms.  You will be capturing waveforms once per line cycle, enough to be useful.  When voltage phase is lagging current, the H-Bridge output will show a larger noise spike at switching (caused by IGBT diode reverse-recovery snap-off).  At zero-phase there is sometimes a triple-transition on H-Bridge outputs - rising,falling,rising in rapid succession instead of a clean rising edge.  Slightly more phase lead (ideal point) and H-Bridge outputs will transition cleanly and smoothly.
David Knierim

Offline Miki_407

  • High Voltage Enthusiast
  • *
  • Posts: 23
  • Karma: +0/-0
    • View Profile
Re: I started making a drsstc
« Reply #11 on: January 16, 2021, 09:38:08 PM »
What is the full part number for "40n60n"?
Full number is 40n60npfd.

Also, what gate voltage are you running (in other words, what supply voltage is running to the UD2.7 board)?
I am running 20v.

Do you have a scope probe capable of measuring 340V waveforms even if not isolated?
I have 10x probe rated at 600v CAT II but I think my scope is made for max 6v with 1x probe so answer is I cant measure 340v. I haven't tested my coil at 300v yet max i have gone to is 120v.

Offline davekni

  • High Voltage Senior
  • *****
  • Posts: 869
  • Karma: +41/-0
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: I started making a drsstc
« Reply #12 on: January 16, 2021, 10:09:21 PM »
I've found data for an IGBT part SGT40N60NPFDPN.  I'm guessing that is what you have.  It is rated for 120A peak, 40A at 100C case, 80A at 25C case temperature.  My rule-of-thumb is that IGBTs fry around 2x rated peak current or 4x rated average current in DRSSTC use.  That would be about 240A per IGBT, 480A for a pair IF they share current perfectly evenly.  That is destruction current, so you want OCD a ways below that, perhaps 300A.  I'd start even lower, ~200A until you have phase lead dialed in.  Others here may have more experience with similar parts.

Sometimes there is enough switching glitch showing up when probing driver output (GDT input) to use for phase lead adjustment.  It is hard to predict exactly what you will see there.  Another option is to form a couple turns (loops) of wire from scope probe tip to ground lead.  Tape over the wire ends (over the probe tip and ground clip) to avoid bumping any high-voltage nodes.  Use this as a magnetic-field probe around the IGBTs or VBus leads to the bridge.  That will often pick up enough signal to see the switching edges.  You will need to experiment with loop size and placement to get clear pulses (or at least spikes and ring-down) at switching times.
David Knierim

High Voltage Forum

Re: I started making a drsstc
« Reply #12 on: January 16, 2021, 10:09:21 PM »

 


* Recent Topics and Posts

post Re: Difference between halfbridge driver ICs and low/high side drivers?
[Electronic Circuits]
johnnyzoo
Today at 07:17:42 PM
post Re: Alternative phase lead
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
Today at 07:12:46 PM
post Re: 8 ft spark french tesla coil
[Spark Gap Tesla Coils (SGTC)]
davekni
Today at 06:44:11 PM
post Re: 8 ft spark french tesla coil
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
Today at 03:39:51 PM
post Alternative phase lead
[Dual Resonant Solid State Tesla coils (DRSSTC)]
panjaksli
Today at 10:24:39 AM
post Re: 8 ft spark french tesla coil
[Spark Gap Tesla Coils (SGTC)]
paulj
Today at 09:40:18 AM
post Re: 833A Cathode Modulation
[Vacuum Tube Tesla Coils (VTTC)]
kyledellaquila
Today at 07:04:38 AM
post Re: 833A Cathode Modulation
[Vacuum Tube Tesla Coils (VTTC)]
kyledellaquila
Today at 06:43:43 AM
post Difference between halfbridge driver ICs and low/high side drivers?
[Electronic Circuits]
Arcatarter
Today at 05:49:11 AM
post Re: 8 ft spark french tesla coil
[Spark Gap Tesla Coils (SGTC)]
davekni
January 25, 2021, 11:51:44 PM
post Re: 8 ft spark french tesla coil
[Spark Gap Tesla Coils (SGTC)]
paulj
January 25, 2021, 10:02:48 PM
post Re: 833A Cathode Modulation
[Vacuum Tube Tesla Coils (VTTC)]
Weston
January 25, 2021, 09:16:22 PM
post Re: Anybody got some tips for releasing a product?
[General Chat]
Weston
January 25, 2021, 08:21:56 PM
post Re: 8 ft spark french tesla coil
[Spark Gap Tesla Coils (SGTC)]
Bradselph
January 25, 2021, 07:38:55 PM
post Re: 833A Cathode Modulation
[Vacuum Tube Tesla Coils (VTTC)]
SalinsLV
January 25, 2021, 05:07:56 PM
post Re: Anybody got some tips for releasing a product?
[General Chat]
TMaxElectronics
January 25, 2021, 05:02:34 PM
post Re: GU5B VTTC Flashover
[Vacuum Tube Tesla Coils (VTTC)]
SalinsLV
January 25, 2021, 04:48:02 PM
post Re: GU5B VTTC Flashover
[Vacuum Tube Tesla Coils (VTTC)]
MRMILSTAR
January 25, 2021, 04:42:52 PM
post Re: Next Gen DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Netzpfuscher
January 25, 2021, 01:42:42 PM
post Re: Enclosure design considerations for a DRSSTC?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
GrantV
January 25, 2021, 12:35:57 PM
post Re: 8 ft spark french tesla coil
[Spark Gap Tesla Coils (SGTC)]
paulj
January 25, 2021, 12:13:33 PM
post Re: Enclosure design considerations for a DRSSTC?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
GrantV
January 25, 2021, 12:06:31 PM
post Re: Anybody got some tips for releasing a product?
[General Chat]
Mads Barnkob
January 25, 2021, 11:24:37 AM
post Re: A new type of eBay drsstc driver?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
JCF
January 25, 2021, 11:24:16 AM
post Re: Paralleling IGBT bricks for H-bridge
[Solid State Tesla Coils (SSTC)]
Mads Barnkob
January 25, 2021, 11:18:30 AM
post Re: 8 ft spark french tesla coil
[Spark Gap Tesla Coils (SGTC)]
Mads Barnkob
January 25, 2021, 11:14:45 AM
post Re: Enclosure design considerations for a DRSSTC?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
January 25, 2021, 09:20:51 AM
post Re: GU5B VTTC Flashover
[Vacuum Tube Tesla Coils (VTTC)]
Mads Barnkob
January 25, 2021, 09:02:35 AM
post Re: 833A Cathode Modulation
[Vacuum Tube Tesla Coils (VTTC)]
Mads Barnkob
January 25, 2021, 08:56:02 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic Circuits]
Mads Barnkob
January 25, 2021, 08:37:01 AM
post Re: Enclosure design considerations for a DRSSTC?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
acobaugh
January 25, 2021, 08:16:23 AM
post Re: Next Gen DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
acobaugh
January 25, 2021, 07:33:26 AM
post Re: ZVS driven Plasma Ball (w/ segmented PTFE Secondary)
[Transformer (Ferrite Core)]
zytra
January 25, 2021, 04:12:05 AM
post Re: ZVS driven Plasma Ball (w/ segmented PTFE Secondary)
[Transformer (Ferrite Core)]
davekni
January 25, 2021, 03:31:13 AM
post Re: ZVS driven Plasma Ball (w/ segmented PTFE Secondary)
[Transformer (Ferrite Core)]
zytra
January 25, 2021, 02:39:08 AM
post Re: Blackbody Radiation and Thermal Control of Satelites.
[General Chat]
klugesmith
January 24, 2021, 10:18:13 PM
post Re: Next Gen DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
TMaxElectronics
January 24, 2021, 10:13:16 PM
post Re: 833A Maximum Dissipation Ratings
[Vacuum Tube Tesla Coils (VTTC)]
kyledellaquila
January 24, 2021, 07:11:20 PM
post 833A Cathode Modulation
[Vacuum Tube Tesla Coils (VTTC)]
kyledellaquila
January 24, 2021, 07:09:52 PM
post GU5B VTTC Flashover
[Vacuum Tube Tesla Coils (VTTC)]
SalinsLV
January 24, 2021, 03:01:46 PM
post Re: compact midi interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
TMaxElectronics
January 24, 2021, 12:57:53 PM
post Re: Enclosure design considerations for a DRSSTC?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
GrantV
January 24, 2021, 10:26:15 AM
post Re: Enclosure design considerations for a DRSSTC?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
acobaugh
January 24, 2021, 06:09:48 AM
post Blackbody Radiation and Thermal Control of Satelites.
[General Chat]
Patrick
January 24, 2021, 03:57:45 AM
post Re: Self Oscillating Half Bridge Wonder
[Solid State Tesla Coils (SSTC)]
kyledellaquila
January 23, 2021, 07:22:57 PM
post Re: compact midi interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
octopus1
January 23, 2021, 07:15:46 PM
post Re: Self Oscillating Half Bridge Wonder
[Solid State Tesla Coils (SSTC)]
Magneticitist
January 23, 2021, 06:54:18 PM
post Re: compact midi interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Mads Barnkob
January 23, 2021, 06:39:16 PM
post Re: 833A Maximum Dissipation Ratings
[Vacuum Tube Tesla Coils (VTTC)]
kyledellaquila
January 23, 2021, 05:43:59 PM
post Re: Self Oscillating Half Bridge Wonder
[Solid State Tesla Coils (SSTC)]
Acid Byte
January 23, 2021, 03:40:18 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal