Author Topic: QCW with replaceable ferrite-core primary  (Read 182 times)

Offline davekni

  • High Voltage Senior
  • *****
  • Posts: 595
  • Karma: +33/-0
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
QCW with replaceable ferrite-core primary
« on: October 13, 2020, 01:50:43 AM »
Inspired by Jan's impressive ferrite-core QCW coil here:
https://highvoltageforum.net/index.php?topic=1073.0

and his wishing that the primary could be adjusted, I'm starting a project to make a QCW with replaceable ferrite-core primary.  The idea is to pot the inside of the secondary with a cavity for the primary.  However, a plain cavity would form corona discharge between the inside surface of the cavity and the primary.  So, here's the secondary form and cavity I plan to pot inside in a couple days:





The cavity is a Faraday cage with no closed loops.  All the wires connect at only the top.  Wires will all be inside the potting material.  At the bottom, I'll connect ONE of the wires to ground.  That way the internal electric field of the secondary will return to the Faraday cage within potting material.  Internal electric field around the primary will be due to only the primary voltage, low enough to avoid corona.  Magnetic field will be free to pass between Faraday cage wires.

Anyone see any issues before I mix and pour epoxy?  I will be using vacuum to remove as much air as possible, per what I've learned on this forum.

This is the first step of a long project.  Haven't built any of the electronics yet.  My aim is to explore lower frequency and longer ramp times than typical for QCW, to see if slow ramps can compensate for lower frequency.  Somewhere around 170kHz and 100ms ramp.
David Knierim

Offline Uspring

  • High Voltage Technician
  • ***
  • Posts: 186
  • Karma: +15/-0
  • Physicist
    • View Profile
Re: QCW with replaceable ferrite-core primary
« Reply #1 on: October 17, 2020, 03:06:49 PM »
Lovely idea to improve on dr. kilovolts design by making the primary removeable with a Faraday cage. I'm wondering, whether an iron core actually increases coupling. Have you any estimates on this?

I'm certainly fond of any research on arc behaviour.

Offline davekni

  • High Voltage Senior
  • *****
  • Posts: 595
  • Karma: +33/-0
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: QCW with replaceable ferrite-core primary
« Reply #2 on: October 17, 2020, 07:45:56 PM »
I made a mock-up by winding old power cords into roughly the intended geometry.  Coupling for that was 0.875.  Didn't measure coupling without the ferrite core, but would guess around 0.7 or just under.

Potting had some problems.  Developed air leaks around the top seal (bottom during potting) during vacuum degassing.  Managed to mostly patch those before epoxy cured, but it's not degassed very well.  May still be OK.  I read that QCW voltage is around 50kV.  Even if low-frequency raises that to 100kV, this potting may be sufficient.  Radial distance is 21mm epoxy plus 5.8mm PVC pipe wall.  Axial distance at the top is 30mm epoxy plus 6.1mm polycarbonate.

Uspring, Thank you for your modeling too.  I've done a bit of magnetics modeling, but don't know enough about arcs to simulate those.

BTW, completely unrelated except for modeling, but I'm hoping to do some simple one-dimensional gas pressure/flow modeling for a  supersonic ping pong ball launcher.  Had the Guinness speed record for a while, and plan eventually to reclaim that record.
/>
/>
David Knierim

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1524
  • Karma: +27/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: QCW with replaceable ferrite-core primary
« Reply #3 on: October 18, 2020, 07:18:08 AM »
Interesting project, something that has been talked about, especially the internal primary coils and potting, but the shielding and other measures of actually making it feasible are new to me, looking forward to follow this.

In regard to low frequency QCW, there might be a little knowledge to get out of my failed attempt of making it simple: http://kaizerpowerelectronics.dk/tesla-coils/kaizer-drsstc-iv/

Regarding shielding around magnetic components, perhaps you can find inspiration in the Pearson Current Monitor 1330 I took apart, I was surprised that it was fully copper shielded in 2 layers with only a small slot cut through it:  https://4hv.org/e107_plugins/forum/forum_viewtopic.php?p=1&id=175696#post-175696 (I can make a repost here on hvf with full size pictures if you want?)
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline johnf

  • High Voltage Technician
  • ***
  • Posts: 137
  • Karma: +4/-0
    • View Profile
Re: QCW with replaceable ferrite-core primary
« Reply #4 on: October 18, 2020, 08:25:41 PM »
Dave
I saw a vacuum cannon with ping pong balls at Richard Hulls place a few years ago from memory it went at around 2000 ft per sec and had no trouble going through water filled soda cans barrel was about 16 feet long. I think it used sacrificial thin mylar windows. Always wondered about doing it with golf balls??

Offline davekni

  • High Voltage Senior
  • *****
  • Posts: 595
  • Karma: +33/-0
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: QCW with replaceable ferrite-core primary
« Reply #5 on: October 19, 2020, 05:32:05 AM »
Mads,

Thank you for reminding me about your simple line-power-cycle-ramped QCW.  I'd looked through that project when I first found this forum a year ago, but had forgotten that it was also low-frequency for a QCW.  For initial experiments, before I build a proper ramp generator, I'm thinking of trying a resonant ramp generator.  Charged bulk cap array feeds a large series inductor into another bulk cap array, with thyristor for trigger.  I have some MOT primary halves left from my eddy-current levitation demo.  Should make something similar to your line quarter-cycle without risk to other line-powered devices.  (I've seen a vacuum-tube coil powered by isolated line half-cycles as in your demo, behaving much like QCW coils.)

I use a somewhat similar slightly-over-one-wrap of insulated copper foil to shield the first stage of my DRSSTC current transformer.  Likely not needed.  For this QCW primary, copper foil could work around the circumference, but not at the top end.  Most of the primary magnetic field is passing out its top end.  There's no way to make a non-shorted turn in the plane where magnetic field passes through.  That's why the array of wires.

John,

Golf balls could be launched with gun powder and a bit of packing to insulate the ball.  Ping pong balls take more finesse, so a more fun challenge.  Also more impressive to see what a 2.7g ball can do, going through 3/4" plywood (nominal 3/4, actually 17mm).  Our (a father-son project) official record is 806m/s.  We since hit 873m/s (2764f/s), shown in the later videos.  (The "smarter every day" youtube channel has a video of supersonic baseball launching.)
David Knierim

High Voltage Forum

Re: QCW with replaceable ferrite-core primary
« Reply #5 on: October 19, 2020, 05:32:05 AM »

 


* Recent Topics and Posts

post Re: current limiting to parallel resonance circuit
[Beginners]
davekni
October 19, 2020, 11:02:11 PM
post Re: Quasar60 DRSSTC build using universal driver/interupter
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
October 19, 2020, 10:53:26 PM
post Re: Tesla coil circuit draws lots of current but the spark size is small.
[Solid State Tesla Coils (SSTC)]
davekni
October 19, 2020, 10:50:35 PM
post Re: Quasar60 DRSSTC build using universal driver/interupter
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Zipdox
October 19, 2020, 09:51:57 PM
post Re: current limiting to parallel resonance circuit
[Beginners]
Zipdox
October 19, 2020, 09:48:07 PM
post Re: Tesla coil circuit draws lots of current but the spark size is small.
[Solid State Tesla Coils (SSTC)]
SalinsLV
October 19, 2020, 07:27:59 PM
post Re: Quasar60 DRSSTC build using universal driver/interupter
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
October 19, 2020, 06:48:03 PM
post Re: UD2.9 skip pulse assembled
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hydron
October 19, 2020, 03:54:00 PM
post Re: UD2.9 skip pulse assembled
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Maju
October 19, 2020, 10:25:25 AM
post Re: Quasar60 DRSSTC build using universal driver/interupter
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Zipdox
October 19, 2020, 08:56:13 AM
post Re: UD2.9 skip pulse assembled
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Netzpfuscher
October 19, 2020, 07:54:05 AM
post Re: QCW with replaceable ferrite-core primary
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
October 19, 2020, 05:32:05 AM
post Re: DIY DC-10MHz optical-fiber-isolated scope probe
[Laboratories, Equipment and Tools]
davekni
October 19, 2020, 05:12:05 AM
post Re: Quasar60 DRSSTC build using universal driver/interupter
[Dual Resonant Solid State Tesla coils (DRSSTC)]
RoadReaper
October 19, 2020, 04:13:30 AM
post Re: UD2.9 skip pulse assembled
[Dual Resonant Solid State Tesla coils (DRSSTC)]
profdc9
October 19, 2020, 03:39:49 AM
post Re: 6" Coil Update now 72" and better lighting
[Spark Gap Tesla Coils (SGTC)]
Bradselph
October 19, 2020, 01:53:01 AM
post Re: UD2.9 skip pulse assembled
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Max
October 19, 2020, 12:36:38 AM
post Re: 10 kW Induction Stove Teardown, Huge SMEG 5-Zone Stove
[Electronic Circuits]
Max
October 18, 2020, 11:57:02 PM
post Re: UD2.9 skip pulse assembled
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Maju
October 18, 2020, 11:14:53 PM
post 10 kW Induction Stove Teardown, Huge SMEG 5-Zone Stove
[Electronic Circuits]
Mads Barnkob
October 18, 2020, 10:42:01 PM
post Re: UD2.9 skip pulse assembled
[Dual Resonant Solid State Tesla coils (DRSSTC)]
profdc9
October 18, 2020, 09:54:48 PM
post Re: QCW with replaceable ferrite-core primary
[Dual Resonant Solid State Tesla coils (DRSSTC)]
johnf
October 18, 2020, 08:25:41 PM
post Re: UD2.9 skip pulse assembled
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Maju
October 18, 2020, 03:28:04 PM
post Re: current limiting to parallel resonance circuit
[Beginners]
Hydron
October 18, 2020, 12:08:36 PM
post Re: current limiting to parallel resonance circuit
[Beginners]
plasma
October 18, 2020, 07:31:58 AM
post Re: QCW with replaceable ferrite-core primary
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
October 18, 2020, 07:18:08 AM
post Re: 6" Coil Update now 72" and better lighting
[Spark Gap Tesla Coils (SGTC)]
Mads Barnkob
October 18, 2020, 07:00:13 AM
post Re: DIY DC-10MHz optical-fiber-isolated scope probe
[Laboratories, Equipment and Tools]
Mads Barnkob
October 18, 2020, 06:50:25 AM
post Re: Gate resistor bypass diode on KaizerSSTC
[Solid State Tesla Coils (SSTC)]
Mads Barnkob
October 18, 2020, 06:39:34 AM
post Re: current limiting to parallel resonance circuit
[Beginners]
davekni
October 18, 2020, 05:15:50 AM
post Re: current limiting to parallel resonance circuit
[Beginners]
Zipdox
October 17, 2020, 11:26:45 PM
post Re: 6" Coil Update now 72" and better lighting
[Spark Gap Tesla Coils (SGTC)]
Zipdox
October 17, 2020, 11:16:24 PM
post Re: steam engine
[Capacitor Banks]
plasma
October 17, 2020, 09:42:50 PM
post Re: steam engine
[Capacitor Banks]
davekni
October 17, 2020, 09:05:37 PM
post Re: DRSSTC with litz-wire primary and 40 x TO247 IGBT H-Bridge
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
October 17, 2020, 08:23:11 PM
post Re: QCW with replaceable ferrite-core primary
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
October 17, 2020, 07:45:56 PM
post Re: DRSSTC with litz-wire primary and 40 x TO247 IGBT H-Bridge
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Uspring
October 17, 2020, 03:26:32 PM
post Re: QCW with replaceable ferrite-core primary
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Uspring
October 17, 2020, 03:06:49 PM
post Re: steam engine
[Capacitor Banks]
plasma
October 17, 2020, 06:17:07 AM
post Re: steam engine
[Capacitor Banks]
davekni
October 17, 2020, 04:15:07 AM
post Re: Syntherrupter - Build by AstRii
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
AstRii
October 16, 2020, 07:41:01 PM
post Re: steam engine
[Capacitor Banks]
plasma
October 16, 2020, 08:36:35 AM
post Re: 6" Coil Update now 72" and better lighting
[Spark Gap Tesla Coils (SGTC)]
Bradselph
October 15, 2020, 09:47:27 PM
post Re: steam engine
[Capacitor Banks]
Twospoons
October 15, 2020, 09:37:29 PM
post Re: Syntherrupter - Build by AstRii
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Max
October 15, 2020, 09:18:14 PM
post Re: DIY DC-10MHz optical-fiber-isolated scope probe
[Laboratories, Equipment and Tools]
davekni
October 14, 2020, 07:44:42 PM
post Re: Gate resistor bypass diode on KaizerSSTC
[Solid State Tesla Coils (SSTC)]
davekni
October 14, 2020, 07:33:16 PM
post Re: steam engine
[Capacitor Banks]
plasma
October 14, 2020, 05:06:54 PM
post Re: Gate resistor bypass diode on KaizerSSTC
[Solid State Tesla Coils (SSTC)]
Zipdox
October 14, 2020, 03:45:05 PM
post Re: DIY DC-10MHz optical-fiber-isolated scope probe
[Laboratories, Equipment and Tools]
Hydron
October 14, 2020, 09:53:14 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal