Author Topic: Recording a variac  (Read 110 times)

Offline klugesmith

  • High Voltage Engineer
  • ****
  • Posts: 297
  • Karma: +7/-0
    • View Profile
Recording a variac
« on: October 11, 2020, 06:18:10 PM »
Rikkitikkitavi might like this. 
A nice 1.4-kVA variac had a power cord so old, its rubber jacket was cracked and splitting along most of its length.  Was becoming scary to use.

It was time to replace the cord, which had 2 conductors and a polarized plug complementing the variac's output receptacle.
This variac is for the lab, not for a museum, so it received the cord from a dead MWO.  16 AWG with three conductors and a ring lug on the grounding conductor.  How to connect the ground?

Die-cast cover had a blind hole molded into one inside corner, as if for 3-wire corded model.
Not threaded, but matching the tap drill size for an 8-32 screw, like the long screws for cover attachment.
My only 8-32 tap has a long taper, so I needed to drill the hole a little deeper to finish the job.

[edit] The major diameter of 8-32 thread is 4.2 mm.  In my experience it's the "standard" thread for securing wires in household electrical devices in USA.   In the original Powerstat, all connections were soldered except for spade lugs under 8-32 screws at the internal variac terminal plate.
« Last Edit: October 11, 2020, 10:33:00 PM by klugesmith »

Offline johnf

  • High Voltage Technician
  • ***
  • Posts: 139
  • Karma: +4/-0
    • View Profile
Re: Recording a variac
« Reply #1 on: October 11, 2020, 08:44:54 PM »
I would have drilled a hole through the side offset from the cord grip to allow use of a nut and bolt and spring washer.
AS/NZS3100 states a minimum of a 4mm bolt that is solely used for earthing purposes

Offline rikkitikkitavi

  • High Voltage Experimenter
  • **
  • Posts: 68
  • Karma: +1/-0
    • View Profile
Re: Recording a variac
« Reply #2 on: October 11, 2020, 09:47:31 PM »
You sexy little thing :)
(the variac)

I presume you test GND from wall plug to the main body chassis, so that the screws holding the cover to the main body makes a good connection?
It looks like aluminium and hence some oxide might give a higher GND resistance. Anyhow nice work.

I have had a few Powerstats passing thru my hands, even all the way over to Sweden and feel their ruggedness and the impressive "Powerkote" and black goo on firmly anchoring the winding.

The old catalouge in a nice 60ies layout/type from Superior Electric.

I have modified one old variac in just the manner johnf describes, but it was a steel chassis, perhaps for magnetic shielding but I mostly use it with my insulating transformer OR a earth fault circuit breaker.  Anyhow  I cant choose not to because I had an electrican remake the entire fuseboard in my house just after moving in  and hence EFCB where mandatory but atleast I have split all 40some fuses on three groups so not everything goes black when I f-k up... and that I do sometimes.

A man can not have too many variacs

High Voltage Forum

Re: Recording a variac
« Reply #2 on: October 11, 2020, 09:47:31 PM »

 


* Recent Topics and Posts

post Re: How to drive these flybacks?
[Transformer (Ferrite Core)]
Alberto
Today at 08:53:46 PM
post Re: How to drive these flybacks?
[Transformer (Ferrite Core)]
davekni
Today at 08:29:08 PM
post Re: Polyphonic Interrupter with STM32F103C8T6 (Bluepill)
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Zipdox
Today at 07:27:43 PM
post Re: Current transformer for narrow spaces
[Laboratories, Equipment and Tools]
klugesmith
Today at 05:14:51 PM
post Re: SuperCascode Designs
[Solid State Tesla Coils (SSTC)]
kyledellaquila
Today at 06:41:46 AM
post Re: 833A Maximum Dissipation Ratings
[Vacuum Tube Tesla Coils (VTTC)]
kyledellaquila
Today at 06:30:05 AM
post Re: How to drive these flybacks?
[Transformer (Ferrite Core)]
Alberto
Today at 12:15:00 AM
post Re: How to drive these flybacks?
[Transformer (Ferrite Core)]
ElectroXa
October 27, 2020, 11:21:00 PM
post Re: Capacitors and arcs
[Beginners]
Alberto
October 27, 2020, 11:06:37 PM
post How to drive these flybacks?
[Transformer (Ferrite Core)]
Alberto
October 27, 2020, 10:14:33 PM
post Re: Lecroy Waverunner 6000a - is it worth for hobby use?
[Laboratories, Equipment and Tools]
Twospoons
October 27, 2020, 10:07:01 PM
post Re: Lecroy Waverunner 6000a - is it worth for hobby use?
[Laboratories, Equipment and Tools]
flyglas
October 27, 2020, 07:41:41 PM
post Re: Lecroy Waverunner 6000a - is it worth for hobby use?
[Laboratories, Equipment and Tools]
plasma
October 27, 2020, 10:57:52 AM
post Re: Lecroy Waverunner 6000a - is it worth for hobby use?
[Laboratories, Equipment and Tools]
Mads Barnkob
October 27, 2020, 09:17:46 AM
post Re: Lecroy Waverunner 6000a - is it worth for hobby use?
[Laboratories, Equipment and Tools]
Hydron
October 27, 2020, 08:01:12 AM
post Re: Lecroy Waverunner 6000a - is it worth for hobby use?
[Laboratories, Equipment and Tools]
Twospoons
October 27, 2020, 05:13:58 AM
post Re: IGBT brick internal gate resistor power dissipation
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
October 26, 2020, 10:25:19 PM
post Re: IGBT brick internal gate resistor power dissipation
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
October 26, 2020, 09:43:44 PM
post Agilent Markes UNITY Thermal Desorber Teardown - Gas Chromatography
[Electronic Circuits]
Mads Barnkob
October 26, 2020, 08:29:12 PM
post Re: IGBT brick internal gate resistor power dissipation
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
October 26, 2020, 08:23:48 PM
post Re: 833A Maximum Dissipation Ratings
[Vacuum Tube Tesla Coils (VTTC)]
Mads Barnkob
October 26, 2020, 08:19:37 PM
post Re: SuperCascode Designs
[Solid State Tesla Coils (SSTC)]
johnf
October 26, 2020, 07:35:00 PM
post Re: Fake or Real DC to DC Solid State Relays.
[Electronic Circuits]
petespaco
October 26, 2020, 06:02:01 PM
post Re: Fake or Real DC to DC Solid State Relays.
[Electronic Circuits]
petespaco
October 26, 2020, 03:22:08 PM
post Re: Fake or Real DC to DC Solid State Relays.
[Electronic Circuits]
T3sl4co1l
October 26, 2020, 03:09:06 PM
post Re: SuperCascode Designs
[Solid State Tesla Coils (SSTC)]
T3sl4co1l
October 26, 2020, 02:55:59 PM
post Re: 833A Maximum Dissipation Ratings
[Vacuum Tube Tesla Coils (VTTC)]
T3sl4co1l
October 26, 2020, 02:49:25 PM
post Re: RC snubbers
[Solid State Tesla Coils (SSTC)]
T3sl4co1l
October 26, 2020, 02:41:18 PM
post Re: steam engine
[Capacitor Banks]
plasma
October 26, 2020, 11:35:48 AM
post Re: Lecroy Waverunner 6000a - is it worth for hobby use?
[Laboratories, Equipment and Tools]
johnnyzoo
October 26, 2020, 09:57:55 AM
post Re: Popped two IRFP460s while testing at 325V
[Solid State Tesla Coils (SSTC)]
Zipdox
October 26, 2020, 08:38:51 AM
post IGBT brick internal gate resistor power dissipation
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
October 26, 2020, 05:33:01 AM
post Re: steam engine
[Capacitor Banks]
Twospoons
October 26, 2020, 04:39:41 AM
post Re: Fake or Real DC to DC Solid State Relays.
[Electronic Circuits]
davekni
October 26, 2020, 03:02:12 AM
post Re: steam engine
[Capacitor Banks]
plasma
October 26, 2020, 01:48:58 AM
post Re: Popped two IRFP460s while testing at 325V
[Solid State Tesla Coils (SSTC)]
davekni
October 26, 2020, 01:03:25 AM
post Re: steam engine
[Capacitor Banks]
davekni
October 26, 2020, 12:51:33 AM
post Fake or Real DC to DC Solid State Relays.
[Electronic Circuits]
petespaco
October 26, 2020, 12:35:41 AM
post Re: DIY capacitor
[Capacitor Banks]
Alberto
October 25, 2020, 11:46:31 PM
post Popped two IRFP460s while testing at 325V
[Solid State Tesla Coils (SSTC)]
Zipdox
October 25, 2020, 11:25:26 PM
post 833A Maximum Dissipation Ratings
[Vacuum Tube Tesla Coils (VTTC)]
kyledellaquila
October 25, 2020, 11:16:17 PM
post SuperCascode Designs
[Solid State Tesla Coils (SSTC)]
kyledellaquila
October 25, 2020, 10:36:58 PM
post Re: DIY capacitor
[Capacitor Banks]
plasma
October 25, 2020, 09:59:37 PM
post Re: steam engine
[Capacitor Banks]
plasma
October 25, 2020, 09:50:03 PM
post Lecroy Waverunner 6000a - is it worth for hobby use?
[Laboratories, Equipment and Tools]
flyglas
October 25, 2020, 07:29:38 PM
post Re: DIY current transformer for measuring primary current?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
October 25, 2020, 06:19:51 PM
post Re: DIY capacitor
[Capacitor Banks]
Alberto
October 25, 2020, 03:09:42 PM
post Re: DIY current transformer for measuring primary current?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Daniel Uhrenholt
October 25, 2020, 09:41:48 AM
post Re: DIY current transformer for measuring primary current?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
plasma
October 25, 2020, 01:46:20 AM
post Re: DIY current transformer for measuring primary current?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hydron
October 24, 2020, 11:12:37 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal