Author Topic: Recording a variac  (Read 95 times)

Offline klugesmith

  • High Voltage Engineer
  • ****
  • Posts: 291
  • Karma: +7/-0
    • View Profile
Recording a variac
« on: October 11, 2020, 06:18:10 PM »
Rikkitikkitavi might like this. 
A nice 1.4-kVA variac had a power cord so old, its rubber jacket was cracked and splitting along most of its length.  Was becoming scary to use.

It was time to replace the cord, which had 2 conductors and a polarized plug complementing the variac's output receptacle.
This variac is for the lab, not for a museum, so it received the cord from a dead MWO.  16 AWG with three conductors and a ring lug on the grounding conductor.  How to connect the ground?

Die-cast cover had a blind hole molded into one inside corner, as if for 3-wire corded model.
Not threaded, but matching the tap drill size for an 8-32 screw, like the long screws for cover attachment.
My only 8-32 tap has a long taper, so I needed to drill the hole a little deeper to finish the job.

[edit] The major diameter of 8-32 thread is 4.2 mm.  In my experience it's the "standard" thread for securing wires in household electrical devices in USA.   In the original Powerstat, all connections were soldered except for spade lugs under 8-32 screws at the internal variac terminal plate.
« Last Edit: October 11, 2020, 10:33:00 PM by klugesmith »

Offline johnf

  • High Voltage Technician
  • ***
  • Posts: 137
  • Karma: +4/-0
    • View Profile
Re: Recording a variac
« Reply #1 on: October 11, 2020, 08:44:54 PM »
I would have drilled a hole through the side offset from the cord grip to allow use of a nut and bolt and spring washer.
AS/NZS3100 states a minimum of a 4mm bolt that is solely used for earthing purposes

Offline rikkitikkitavi

  • High Voltage Experimenter
  • **
  • Posts: 68
  • Karma: +1/-0
    • View Profile
Re: Recording a variac
« Reply #2 on: October 11, 2020, 09:47:31 PM »
You sexy little thing :)
(the variac)

I presume you test GND from wall plug to the main body chassis, so that the screws holding the cover to the main body makes a good connection?
It looks like aluminium and hence some oxide might give a higher GND resistance. Anyhow nice work.

I have had a few Powerstats passing thru my hands, even all the way over to Sweden and feel their ruggedness and the impressive "Powerkote" and black goo on firmly anchoring the winding.

The old catalouge in a nice 60ies layout/type from Superior Electric.

I have modified one old variac in just the manner johnf describes, but it was a steel chassis, perhaps for magnetic shielding but I mostly use it with my insulating transformer OR a earth fault circuit breaker.  Anyhow  I cant choose not to because I had an electrican remake the entire fuseboard in my house just after moving in  and hence EFCB where mandatory but atleast I have split all 40some fuses on three groups so not everything goes black when I f-k up... and that I do sometimes.

A man can not have too many variacs

High Voltage Forum

Re: Recording a variac
« Reply #2 on: October 11, 2020, 09:47:31 PM »

 


* Recent Topics and Posts

post Re: current limiting to parallel resonance circuit
[Beginners]
davekni
October 19, 2020, 11:02:11 PM
post Re: Quasar60 DRSSTC build using universal driver/interupter
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
October 19, 2020, 10:53:26 PM
post Re: Tesla coil circuit draws lots of current but the spark size is small.
[Solid State Tesla Coils (SSTC)]
davekni
October 19, 2020, 10:50:35 PM
post Re: Quasar60 DRSSTC build using universal driver/interupter
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Zipdox
October 19, 2020, 09:51:57 PM
post Re: current limiting to parallel resonance circuit
[Beginners]
Zipdox
October 19, 2020, 09:48:07 PM
post Re: Tesla coil circuit draws lots of current but the spark size is small.
[Solid State Tesla Coils (SSTC)]
SalinsLV
October 19, 2020, 07:27:59 PM
post Re: Quasar60 DRSSTC build using universal driver/interupter
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
October 19, 2020, 06:48:03 PM
post Re: UD2.9 skip pulse assembled
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hydron
October 19, 2020, 03:54:00 PM
post Re: UD2.9 skip pulse assembled
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Maju
October 19, 2020, 10:25:25 AM
post Re: Quasar60 DRSSTC build using universal driver/interupter
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Zipdox
October 19, 2020, 08:56:13 AM
post Re: UD2.9 skip pulse assembled
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Netzpfuscher
October 19, 2020, 07:54:05 AM
post Re: QCW with replaceable ferrite-core primary
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
October 19, 2020, 05:32:05 AM
post Re: DIY DC-10MHz optical-fiber-isolated scope probe
[Laboratories, Equipment and Tools]
davekni
October 19, 2020, 05:12:05 AM
post Re: Quasar60 DRSSTC build using universal driver/interupter
[Dual Resonant Solid State Tesla coils (DRSSTC)]
RoadReaper
October 19, 2020, 04:13:30 AM
post Re: UD2.9 skip pulse assembled
[Dual Resonant Solid State Tesla coils (DRSSTC)]
profdc9
October 19, 2020, 03:39:49 AM
post Re: 6" Coil Update now 72" and better lighting
[Spark Gap Tesla Coils (SGTC)]
Bradselph
October 19, 2020, 01:53:01 AM
post Re: UD2.9 skip pulse assembled
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Max
October 19, 2020, 12:36:38 AM
post Re: 10 kW Induction Stove Teardown, Huge SMEG 5-Zone Stove
[Electronic Circuits]
Max
October 18, 2020, 11:57:02 PM
post Re: UD2.9 skip pulse assembled
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Maju
October 18, 2020, 11:14:53 PM
post 10 kW Induction Stove Teardown, Huge SMEG 5-Zone Stove
[Electronic Circuits]
Mads Barnkob
October 18, 2020, 10:42:01 PM
post Re: UD2.9 skip pulse assembled
[Dual Resonant Solid State Tesla coils (DRSSTC)]
profdc9
October 18, 2020, 09:54:48 PM
post Re: QCW with replaceable ferrite-core primary
[Dual Resonant Solid State Tesla coils (DRSSTC)]
johnf
October 18, 2020, 08:25:41 PM
post Re: UD2.9 skip pulse assembled
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Maju
October 18, 2020, 03:28:04 PM
post Re: current limiting to parallel resonance circuit
[Beginners]
Hydron
October 18, 2020, 12:08:36 PM
post Re: current limiting to parallel resonance circuit
[Beginners]
plasma
October 18, 2020, 07:31:58 AM
post Re: QCW with replaceable ferrite-core primary
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
October 18, 2020, 07:18:08 AM
post Re: 6" Coil Update now 72" and better lighting
[Spark Gap Tesla Coils (SGTC)]
Mads Barnkob
October 18, 2020, 07:00:13 AM
post Re: DIY DC-10MHz optical-fiber-isolated scope probe
[Laboratories, Equipment and Tools]
Mads Barnkob
October 18, 2020, 06:50:25 AM
post Re: Gate resistor bypass diode on KaizerSSTC
[Solid State Tesla Coils (SSTC)]
Mads Barnkob
October 18, 2020, 06:39:34 AM
post Re: current limiting to parallel resonance circuit
[Beginners]
davekni
October 18, 2020, 05:15:50 AM
post Re: current limiting to parallel resonance circuit
[Beginners]
Zipdox
October 17, 2020, 11:26:45 PM
post Re: 6" Coil Update now 72" and better lighting
[Spark Gap Tesla Coils (SGTC)]
Zipdox
October 17, 2020, 11:16:24 PM
post Re: steam engine
[Capacitor Banks]
plasma
October 17, 2020, 09:42:50 PM
post Re: steam engine
[Capacitor Banks]
davekni
October 17, 2020, 09:05:37 PM
post Re: DRSSTC with litz-wire primary and 40 x TO247 IGBT H-Bridge
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
October 17, 2020, 08:23:11 PM
post Re: QCW with replaceable ferrite-core primary
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
October 17, 2020, 07:45:56 PM
post Re: DRSSTC with litz-wire primary and 40 x TO247 IGBT H-Bridge
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Uspring
October 17, 2020, 03:26:32 PM
post Re: QCW with replaceable ferrite-core primary
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Uspring
October 17, 2020, 03:06:49 PM
post Re: steam engine
[Capacitor Banks]
plasma
October 17, 2020, 06:17:07 AM
post Re: steam engine
[Capacitor Banks]
davekni
October 17, 2020, 04:15:07 AM
post Re: Syntherrupter - Build by AstRii
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
AstRii
October 16, 2020, 07:41:01 PM
post Re: steam engine
[Capacitor Banks]
plasma
October 16, 2020, 08:36:35 AM
post Re: 6" Coil Update now 72" and better lighting
[Spark Gap Tesla Coils (SGTC)]
Bradselph
October 15, 2020, 09:47:27 PM
post Re: steam engine
[Capacitor Banks]
Twospoons
October 15, 2020, 09:37:29 PM
post Re: Syntherrupter - Build by AstRii
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Max
October 15, 2020, 09:18:14 PM
post Re: DIY DC-10MHz optical-fiber-isolated scope probe
[Laboratories, Equipment and Tools]
davekni
October 14, 2020, 07:44:42 PM
post Re: Gate resistor bypass diode on KaizerSSTC
[Solid State Tesla Coils (SSTC)]
davekni
October 14, 2020, 07:33:16 PM
post Re: steam engine
[Capacitor Banks]
plasma
October 14, 2020, 05:06:54 PM
post Re: Gate resistor bypass diode on KaizerSSTC
[Solid State Tesla Coils (SSTC)]
Zipdox
October 14, 2020, 03:45:05 PM
post Re: DIY DC-10MHz optical-fiber-isolated scope probe
[Laboratories, Equipment and Tools]
Hydron
October 14, 2020, 09:53:14 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal