Author Topic: Estimating spark length voltage  (Read 2918 times)

Offline oneKone

  • High Voltage Engineer
  • ****
  • Posts: 282
  • Karma: +7/-0
    • View Profile
Estimating spark length voltage
« on: September 06, 2017, 02:29:57 AM »
Hey,
A while ago (about 7 years) I read somewhere that a general rule of thumb for estimating a spark length is 1kv for 1mm. I've been blindly using this concept without actually looking into it. I've tried to find some answers but it seems my Google skills are not upto the task!

So basically the question is, is 1kv equal to 1mm or is this far from accurate....... I'm equating my 400mm spark length on my sstc is 400kv.

Cheers,
Chris
« Last Edit: September 06, 2017, 09:59:10 AM by Mads Barnkob »

Online Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1179
  • Karma: +17/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Estimating spark length voktage
« Reply #1 on: September 06, 2017, 09:58:05 AM »
The old 10 kV/cm rule does not apply here, I seem to recall that it is for DC current between pointy objects, the attached short description goes into further detail on the required breakdown voltage for different spark gap geometries.

Tesla coils does however operate quite differently. We charge up a topload, secondary top capacitance, with as many electrons as possible, before the voltage is high enough to break down the dialectric strength of atmospheric air. This can differ with temperature, moisture and pressure.

The topload voltage will always be the greatest just before there is a spark formed, as this is when the charge is at its highest, once the spark starts to grow it represents a larger and larger load to the topload and as current goes up while discharging the energy, the voltage drops significantly.

This is just a bold statement, that for a Tesla coil we are more in the league of 3 kV/cm for long sparks. Terry Fritz once made some measurements on this: https://deanostoybox.com/hot-streamer/TeslaCoils/MyPapers/planant/waveant3.html

Hydron also posted a lot of topload/breakout point current measurements, these numbers can be used to calculate the topload voltage: https://highvoltageforum.net/index.php?topic=117.msg735;topicseen#new
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline Uspring

  • High Voltage Technician
  • ***
  • Posts: 121
  • Karma: +8/-0
  • Physicist
    • View Profile
Re: Estimating spark length voltage
« Reply #2 on: September 06, 2017, 04:47:14 PM »
The differences between DC and AC arcs are mainly 2: An AC arc can end in midair and it usually lasts much longer. The AC arc can grow over many cycles by current flowing back and forth along it, keeping it hot. So once a small arc has broke out, it will establish a conductive channel to its tip from where the arc can grow further. The arc channel won't be a perfect conductor, so the voltage at its tip will gradually decrease as it gets longer. This will basically limit its length. In principle arc length and voltage don't even have to be linearly related. Probably higher frequency arcs are also longer for a given voltage, since charges are more often pushed back and forth, making it hotter and more conductive.

If you're into math, you might want to read https://www.pupman.com/listarchives/2012/Oct/msg00125.html

A back of the envelope calculation based on Hydrons data seems to indicate a voltage of about 300kV for an arc length somewhat above 2 m, i.e. 1.5kV/cm.

Offline oneKone

  • High Voltage Engineer
  • ****
  • Posts: 282
  • Karma: +7/-0
    • View Profile
Re: Estimating spark length voltage
« Reply #3 on: September 07, 2017, 01:40:46 AM »
Cheers for the replies and the links. Looking forward to understanding further

Offline AndreiRS

  • High Voltage Experimenter
  • **
  • Posts: 69
  • Karma: +0/-0
    • View Profile
Re: Estimating spark length voltage
« Reply #4 on: February 17, 2018, 12:12:40 AM »
I couldn't get an arc from a mot with 2kv output, at something like 0.3 maybe 0.4mm. It depends a lot on air humidity.

High Voltage Forum

Re: Estimating spark length voltage
« Reply #4 on: February 17, 2018, 12:12:40 AM »

 


* Recent Topics and Posts

post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
Today at 03:35:40 PM
post Re: Why did 4HV die??
[General chatting]
John123
Today at 03:21:07 PM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
Mads Barnkob
Today at 03:04:28 PM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
Today at 02:57:45 PM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
kamelryttarn
Today at 11:23:48 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
Mads Barnkob
Today at 10:27:54 AM
post Re: Worlds Weirdest Microwave Oven, From A Weapons Factory - The Husqvarna Cupol
[Transformer (iron core)]
Mads Barnkob
Today at 10:20:17 AM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
Mads Barnkob
Today at 10:16:32 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
Today at 06:04:28 AM
post Re: Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
davekni
Today at 05:28:54 AM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
davekni
Today at 04:12:29 AM
post Duty cycle when driving a CRT TV flyback transformer
[Transformer (ferrite core)]
John123
December 09, 2019, 10:52:59 PM
post Replacement guide for Windows Media Center
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
MRMILSTAR
December 09, 2019, 08:29:16 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
Uspring
December 09, 2019, 04:23:33 PM
post Re: Possible use for large inductor (laminated core)
[Transformer (iron core)]
MRMILSTAR
December 09, 2019, 03:59:02 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 09, 2019, 03:41:42 PM
post Possible use for large inductor (laminated core)
[Transformer (iron core)]
kamelryttarn
December 09, 2019, 09:43:11 AM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
davekni
December 09, 2019, 12:53:57 AM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
davekni
December 08, 2019, 09:57:51 PM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
MRMILSTAR
December 08, 2019, 05:28:09 PM
post Aethra CCD Webcam Teardown - From Back When Streaming Was Expensive!
[Electronic circuits]
Mads Barnkob
December 08, 2019, 01:33:30 PM
post Platter resistance & inductance
[Induction launchers, coil guns and rails guns]
klugesmith
December 08, 2019, 11:41:00 AM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
davekni
December 08, 2019, 06:50:11 AM
post Re: CW multiplier resistor string suggestions
[Voltage Multipliers]
plasma
December 08, 2019, 12:00:00 AM
post CW multiplier resistor string suggestions
[Voltage Multipliers]
MRMILSTAR
December 07, 2019, 11:32:49 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 07, 2019, 09:54:31 PM
post Re: SGTC MK1 - An Accomplishment in Progress
[Spark gap Tesla coils]
jturnerkc
December 07, 2019, 09:48:21 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 07, 2019, 08:59:57 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
MRMILSTAR
December 06, 2019, 08:35:29 PM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 06, 2019, 05:19:26 AM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
davekni
December 06, 2019, 03:48:34 AM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
the_anomaly
December 06, 2019, 03:35:39 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General chatting]
AstRii
December 06, 2019, 01:27:03 AM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 05, 2019, 11:38:59 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
Mads Barnkob
December 05, 2019, 07:33:01 PM
post Re: Cost reduction in consumer electrics
[Electronic circuits]
sjsimmo
December 05, 2019, 11:09:20 AM
post Cost reduction in consumer electrics
[Electronic circuits]
klugesmith
December 05, 2019, 07:25:20 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 05, 2019, 05:52:11 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 05, 2019, 05:21:07 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 04, 2019, 06:05:11 PM
post Re: Full bridge showing half the voltage
[Beginners]
shrad
December 04, 2019, 02:57:02 PM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
Uspring
December 04, 2019, 12:40:51 PM
post Re: Full bridge showing half the voltage
[Beginners]
plasma
December 04, 2019, 11:20:25 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 04, 2019, 08:28:15 AM
post Re: Full bridge showing half the voltage
[Beginners]
klugesmith
December 04, 2019, 07:41:21 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
MRMILSTAR
December 04, 2019, 05:15:49 AM
post Re: HV resistor in oil
[Voltage Multipliers]
MRMILSTAR
December 04, 2019, 05:06:39 AM
post Re: HV resistor in oil
[Voltage Multipliers]
davekni
December 04, 2019, 04:31:16 AM
post Re: Full bridge showing half the voltage
[Beginners]
davekni
December 04, 2019, 04:26:38 AM
post Re: Sense coil fabrication?
[Induction launchers, coil guns and rails guns]
klugesmith
December 04, 2019, 04:10:16 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30