Author Topic: Which way would be correct (for primary)  (Read 145 times)

Offline thedoc298

  • High Voltage Enthusiast
  • *
  • Posts: 15
  • Karma: +0/-0
    • View Profile
Which way would be correct (for primary)
« on: April 18, 2019, 09:10:30 PM »

I have read two different methods for the primary center hole, 1st  the hole 2 inches bigger than the secondary. The second method said primary as close to the secondary without shorting. Which one should be used. Thanks again.

Offline Mads Barnkob

  • Administrator
  • High Voltage Senior
  • *****
  • Posts: 990
  • Karma: +15/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Which way would be correct (for primary)
« Reply #1 on: April 23, 2019, 08:54:37 AM »
There is only 2 things to consider when choosing the inner diameter of your primary coil.

- Preventing flash-over between primary coil and secondary base / earthing point
- Coupling between coils

Often the required coupling between the coils will force you to have enough space between the coils so that the first paragraph is not a problem.

I would go with minimum 5 cm / 2" which also leaves you with some room to work in, when everything is fitted too tight together there is no room for servicing.
http://www.kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics

Offline thedoc298

  • High Voltage Enthusiast
  • *
  • Posts: 15
  • Karma: +0/-0
    • View Profile
Re: Which way would be correct (for primary)
« Reply #2 on: April 23, 2019, 05:36:57 PM »
There is only 2 things to consider when choosing the inner diameter of your primary coil.

- Preventing flash-over between primary coil and secondary base / earthing point
- Coupling between coils

Often the required coupling between the coils will force you to have enough space between the coils so that the first paragraph is not a problem.

I would go with minimum 5 cm / 2" which also leaves you with some room to work in, when everything is fitted too tight together there is no room for servicing.

Thanks I went with 2". Got the secondary wound.


« Last Edit: April 23, 2019, 09:33:07 PM by Mads Barnkob »

High Voltage Forum

Re: Which way would be correct (for primary)
« Reply #2 on: April 23, 2019, 05:36:57 PM »

 


* Recent Topics and Posts

post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
Today at 08:31:55 PM
post Re: Easy access to optimal resonance frequency but the benefit is quite small
[Dual Resonant Solid State Tesla coils]
dexter
Today at 08:31:51 PM
post Easy access to optimal resonance frequency but the benefit is quite small
[Dual Resonant Solid State Tesla coils]
VNTC
May 21, 2019, 11:35:57 PM
post Re: Offgrid 48V solar to 24V battery setup
[Electronic circuits]
Mads Barnkob
May 21, 2019, 09:59:54 PM
post Re: General Oscilloscope Probing Techniques for (DR)SSTC h-bridge
[Beginners]
Mads Barnkob
May 21, 2019, 09:51:27 PM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
T3sl4co1l
May 21, 2019, 09:49:03 PM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
82026
May 21, 2019, 09:02:10 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Vaclav
May 21, 2019, 08:59:57 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
May 21, 2019, 08:28:43 PM
post Re: Identification of unknown embedded computer, help needed.
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Mads Barnkob
May 21, 2019, 08:22:28 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Vaclav
May 21, 2019, 06:21:37 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
May 21, 2019, 06:12:55 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
profdc9
May 21, 2019, 04:06:38 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Vaclav
May 21, 2019, 03:56:56 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Vaclav
May 21, 2019, 03:46:56 PM
post Re: DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
profdc9
May 21, 2019, 02:32:59 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
May 21, 2019, 06:12:18 AM
post Re: Offgrid 48V solar to 24V battery setup
[Electronic circuits]
profdc9
May 20, 2019, 11:30:34 PM
post DRSSTC design questions + project progress
[Dual Resonant Solid State Tesla coils]
Vaclav
May 20, 2019, 06:38:54 PM
post Re: General Oscilloscope Probing Techniques for (DR)SSTC h-bridge
[Beginners]
Teravolt
May 20, 2019, 06:33:49 PM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
82026
May 20, 2019, 02:27:59 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
hightemp1
May 20, 2019, 02:57:46 AM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
T3sl4co1l
May 20, 2019, 01:06:27 AM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
82026
May 19, 2019, 09:14:59 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
May 19, 2019, 06:40:41 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
flyrod
May 19, 2019, 04:04:12 PM
post Re: Offgrid 48V solar to 24V battery setup
[Electronic circuits]
Mads Barnkob
May 19, 2019, 11:24:46 AM
post Re: ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
flyrod
May 19, 2019, 03:22:54 AM
post Re: Are bleeder resistors necessary if I can easily discharge my capacitor?
[Spark gap Tesla coils]
profdc9
May 19, 2019, 03:18:52 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
May 18, 2019, 10:48:59 PM
post Re: Is one of these good?
[Dual Resonant Solid State Tesla coils]
Golddustpeak
May 18, 2019, 04:19:11 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
petespaco
May 17, 2019, 10:57:17 PM
post Are bleeder resistors necessary if I can easily discharge my capacitor?
[Spark gap Tesla coils]
jpb133
May 17, 2019, 09:41:56 PM
post Re: Is one of these good?
[Dual Resonant Solid State Tesla coils]
Uspring
May 17, 2019, 12:41:17 PM
post ZVS Mazzilli circ with active gate driver - what causes ringing?
[Electronic circuits]
82026
May 16, 2019, 04:15:58 PM
post Re: Identification of unknown embedded computer, help needed.
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Fumeaux
May 16, 2019, 02:19:39 PM
post Re: Is one of these good?
[Dual Resonant Solid State Tesla coils]
Golddustpeak
May 16, 2019, 01:50:44 PM
post Re: Is one of these good?
[Dual Resonant Solid State Tesla coils]
Uspring
May 16, 2019, 12:17:01 PM
post Re: Identification of unknown embedded computer, help needed.
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Fumeaux
May 16, 2019, 08:45:15 AM
post Re: Identification of unknown embedded computer, help needed.
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Mads Barnkob
May 15, 2019, 11:49:59 PM
post Re: Identification of unknown embedded computer, help needed.
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Hydron
May 15, 2019, 10:51:33 PM
post Identification of unknown embedded computer, help needed.
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Mads Barnkob
May 15, 2019, 09:35:41 PM
post Re: Is one of these good?
[Dual Resonant Solid State Tesla coils]
Golddustpeak
May 15, 2019, 05:07:20 PM
post Re: Mounting LCD CFL's around DRSSTC?
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
May 15, 2019, 12:46:33 PM
post Re: General Oscilloscope Probing Techniques for (DR)SSTC h-bridge
[Beginners]
Mads Barnkob
May 15, 2019, 10:08:11 AM
post Re: Is one of these good?
[Dual Resonant Solid State Tesla coils]
Mads Barnkob
May 15, 2019, 10:04:59 AM
post General Oscilloscope Probing Techniques for (DR)SSTC h-bridge
[Beginners]
L_Mangold
May 15, 2019, 12:42:46 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
hightemp1
May 14, 2019, 11:28:43 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
badpeter
May 14, 2019, 09:58:28 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic circuits]
hightemp1
May 14, 2019, 08:35:28 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30