Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - shifatsrm09

Pages: [1]
1
Solid State Tesla Coils (SSTC) / Slayer exciter circuit troubleshoot.
« on: November 03, 2020, 07:28:35 AM »
I just follow the circuit diagram as shown in the attached image.I use 5 TIP31C transistor in parallel and 20v 10A power supply to power up the circuit but it isnt working i connect the 47k 3watt resistor to my circuit. i change the polarity of primary coil tried everything. after that i check my transistor all are working condition. so i measure the current flow of this circuit as my surprise the current is 0.01. What should i do now? should i change the resistor to low value wat resistor ar the resistance?

2
I stumbled across this video

/>
I want to replicate the circuit from this guys its seems so nice.The mosfet gate driver DS0026 is so rare in my country.I live in Bangladesh,Asia. So i find a alternative i try to find mic 4452 and so many driver but i cant find those in my local and large electronic market.So how i can drive the gate pin without these is there any other component i can use? which is common in everywhere.

3
Solid State Tesla Coils (SSTC) / Help me build up my first tesla coil!
« on: November 01, 2020, 04:42:46 PM »
I try to make a tesla coil for 2 years and after all effort i cant even make a single spark.Maybe my knowladge isnt enough.I try 2n222 transistor slayer exciter i dont know but none of the project work. Than i try with slyaer exciter with some npn transistor here i blew many transistors but can never be success. recenly i try irfp 460 with a ballast and get some spark but my mosfet died. i cant make a efficient circuit . I beg u pls help me to make my tesla coil.

as a beginner i want a slayer exciter circuit which is easy to make hopefully
i dont need a huge spark in my ifrst project but the midium lvl spark will satisfy me much further i beefed up the circuit to the certain level.
 
i know many profesional in this forum would see my post. plz provide me a diagram or syscamatic where i can drive my coil .
or even better if i can play music though my coil.

thanx in advance mate

4
I just came up with a music slayer exciter coil driver i just only made the systamatic by some research. I want to know that should i change something in this circuit diagram or rearrange something cz this isnt working how it shoud be.or I mad the circuit wrong way give me a good suggetion .

5
Solid State Tesla Coils (SSTC) / SSTC with ballast blew my IRFP460
« on: October 29, 2020, 05:18:27 PM »
IM trying to make tesla coil driver with irfp460. I make my circuit like shown in the syscamatic . first things is that for the first attempt I used 1mm thick wire for primary coil then i see that my both ballast get extreamly heated up and also the heatsink attached to the IRFP460 although it was working it throw very very tiny arc from the topload and can light up a normal cfl bulb.
than i go for 3.6mm wire for my primary winding and attached everything as same as before and syscamatic. This time the arc can jump upto 2 inch far away but whithing 20 second my mosfet shorted or blew up i didnt guess it but it dead for sure.
Can anyone help me with this issue or modify my syscamatic so it willme more efficient and work without blowing .

6
Solid State Tesla Coils (SSTC) / SSTC with a ballast circuit not working
« on: October 29, 2020, 03:01:26 AM »
Im trying to make a tesla coil from 2016. After many failures i stopped trying stuffs.But now i discoverd that tesla coil can be made by many other ways.I follow the systematics i attached. I blew up almost 6 IRFP460 mosfet. but it didnt even work not a single spark.Plz guys i want your help

Component I use:
Diode UF5408
1 MKP 250v capacitor
12k 2watt Resistor
12v 1w zener diode
10k potentiometer
5 turn with 3.6mm thick copper wire insulated
1200 turn in secondary
and i use 2*40w ballast as parallel
everything attached together same as syscamatics


Can anyone help how it will work!
it will be great pleasure

Pages: [1]

* Recent Topics and Posts

post Re: Drsstc Driver Board for Tesla Coil Driver Optic Fiber Splice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
iw1esu
Today at 01:56:54 PM
post Cap Identification 64KV
[Capacitor Banks]
Thermionix
Today at 07:14:33 AM
post Re: ZVS driven Plasma Ball (w/ segmented PTFE Secondary)
[Transformer (Ferrite Core)]
zytra
Today at 05:20:21 AM
post Re: ZVS driven Plasma Ball (w/ segmented PTFE Secondary)
[Transformer (Ferrite Core)]
klugesmith
Today at 03:44:12 AM
post Re: ZVS driven Plasma Ball (w/ segmented PTFE Secondary)
[Transformer (Ferrite Core)]
davekni
Today at 03:31:35 AM
post Re: ZVS driven Plasma Ball (w/ segmented PTFE Secondary)
[Transformer (Ferrite Core)]
zytra
Today at 03:01:47 AM
post Re: Cold Gas Satellite Thruster
[General Chat]
klugesmith
Today at 02:53:23 AM
post Re: ZVS driven Plasma Ball (w/ segmented PTFE Secondary)
[Transformer (Ferrite Core)]
davekni
Today at 02:52:00 AM
post Cold Gas Satellite Thruster
[General Chat]
Patrick
Today at 02:02:40 AM
post Re: Segmented PTFE Secondary, Large Plasma Ball project
[Transformer (Ferrite Core)]
zytra
Today at 01:04:03 AM
post Re: Segmented PTFE Secondary, Large Plasma Ball project
[Transformer (Ferrite Core)]
davekni
Today at 12:39:10 AM
post Re: Segmented PTFE Secondary, Large Plasma Ball project
[Transformer (Ferrite Core)]
zytra
January 19, 2021, 11:13:22 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
AeraCura_
January 19, 2021, 10:45:50 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
N1G3L
January 19, 2021, 09:17:18 PM
post Re: Alcatel Lucent B4 RRH2x60-4R teardown and reverse engineering
[Radio Frequency]
Da_Stier
January 19, 2021, 06:20:10 PM
post Fusor power supply
[Voltage Multipliers]
hammertone
January 19, 2021, 05:27:02 PM
post Re: Just a noob with some HV concerns...
[Beginners]
MrScrOggs
January 19, 2021, 01:21:13 PM
post Re: Just a noob with some HV concerns...
[Beginners]
klugesmith
January 19, 2021, 07:04:16 AM
post Re: Segmented PTFE Secondary, Large Plasma Ball project
[Transformer (Ferrite Core)]
zytra
January 19, 2021, 06:37:53 AM
post Re: Segmented PTFE Secondary, Large Plasma Ball project
[Transformer (Ferrite Core)]
davekni
January 19, 2021, 06:16:41 AM
post Re: Segmented PTFE Secondary, Large Plasma Ball project
[Transformer (Ferrite Core)]
zytra
January 19, 2021, 05:00:50 AM
post Re: Segmented PTFE Secondary, Large Plasma Ball project
[Transformer (Ferrite Core)]
davekni
January 19, 2021, 04:03:12 AM
post Just a noob with some HV concerns...
[Beginners]
MrScrOggs
January 19, 2021, 03:07:11 AM
post Re: Segmented PTFE Secondary, Large Plasma Ball project
[Transformer (Ferrite Core)]
zytra
January 19, 2021, 02:57:27 AM
post Re: compact midi interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
TMaxElectronics
January 19, 2021, 12:06:44 AM
post Re: Segmented PTFE Secondary, Large Plasma Ball project
[Transformer (Ferrite Core)]
davekni
January 18, 2021, 11:56:31 PM
post Re: how to run these guys?
[Transformer (Ferrite Core)]
Alberto
January 18, 2021, 11:50:22 PM
post Re: Segmented PTFE Secondary, Large Plasma Ball project
[Transformer (Ferrite Core)]
klugesmith
January 18, 2021, 10:30:15 PM
post Re: Segmented PTFE Secondary, Large Plasma Ball project
[Transformer (Ferrite Core)]
zytra
January 18, 2021, 10:03:46 PM
post Re: Segmented PTFE Secondary, Large Plasma Ball project
[Transformer (Ferrite Core)]
davekni
January 18, 2021, 09:58:44 PM
post Re: Segmented PTFE Secondary, Large Plasma Ball project
[Transformer (Ferrite Core)]
zytra
January 18, 2021, 08:52:29 PM
post Re: Segmented PTFE Secondary, Large Plasma Ball project
[Transformer (Ferrite Core)]
davekni
January 18, 2021, 07:08:09 PM
post Re: Adding interrupter Self oscillating tesla coil
[Beginners]
davekni
January 18, 2021, 06:49:28 PM
post Re: Alcatel Lucent B4 RRH2x60-4R teardown and reverse engineering
[Radio Frequency]
Da_Stier
January 18, 2021, 06:12:44 PM
post Re: Segmented PTFE Secondary, Large Plasma Ball project
[Transformer (Ferrite Core)]
klugesmith
January 18, 2021, 04:53:23 PM
post Adding interrupter Self oscillating tesla coil
[Beginners]
arto
January 18, 2021, 11:54:54 AM
post Re: Segmented PTFE Secondary, Plasma Ball project
[Transformer (Ferrite Core)]
zytra
January 18, 2021, 08:27:18 AM
post Re: Self Oscillating Half Bridge Wonder
[Solid State Tesla Coils (SSTC)]
Acid Byte
January 18, 2021, 06:57:06 AM
post Re: Segmented PTFE Secondary, Plasma Ball project
[Transformer (Ferrite Core)]
davekni
January 18, 2021, 06:43:19 AM
post Re: Segmented PTFE Secondary, Plasma Ball project
[Transformer (Ferrite Core)]
zytra
January 18, 2021, 05:48:27 AM
post Re: how to run these guys?
[Transformer (Ferrite Core)]
klugesmith
January 18, 2021, 01:03:48 AM
post Re: how to run these guys?
[Transformer (Ferrite Core)]
Alberto
January 18, 2021, 12:26:26 AM
post Re: how to run these guys?
[Transformer (Ferrite Core)]
davekni
January 17, 2021, 11:29:04 PM
post Re: how to run these guys?
[Transformer (Ferrite Core)]
Alberto
January 17, 2021, 09:55:24 PM
post Re: Segmented PTFE Secondary, Plasma Ball project
[Transformer (Ferrite Core)]
zytra
January 17, 2021, 09:34:21 PM
post Re: Segmented PTFE Secondary, Plasma Ball project
[Transformer (Ferrite Core)]
davekni
January 17, 2021, 08:51:50 PM
post Re: how to run these guys?
[Transformer (Ferrite Core)]
davekni
January 17, 2021, 08:04:54 PM
post Re: compact midi interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
tophat
January 17, 2021, 05:40:59 PM
post Re: Schlieren images projected onto a wall (no camera)
[Light, Lasers and Optics]
Uspring
January 17, 2021, 05:12:45 PM
post Re: how to run these guys?
[Transformer (Ferrite Core)]
SteveN87
January 17, 2021, 02:20:09 PM

SimplePortal 2.3.6 © 2008-2014, SimplePortal