Author Topic: mini tesla (hopefully not a fail)  (Read 18600 times)

Offline bogdan

  • High Voltage Experimenter
  • **
  • Posts: 55
  • Karma: +0/-0
    • View Profile
mini tesla (hopefully not a fail)
« on: November 03, 2020, 11:19:48 AM »
Hello everyone, after a fail with my attempt to make a big tesla coil, i decided to start smaller, so i built a mini version. However it bothers me that the secondary coil resonates at @835kHz, that high number scares me a little so i stopped to ask a few questions. Is that frequency a bit high ? can i reduce it ? and what driver do you recommend for the primary to deal with such high frequency ?

Offline Zipdox

  • High Voltage Technician
  • ***
  • Posts: 143
  • Karma: +1/-0
    • View Profile
    • Zipdox
Re: mini tesla (hopefully not a fail)
« Reply #1 on: November 03, 2020, 03:29:31 PM »
No that resonance frequency isn't that high at all for a small coil.

Offline bogdan

  • High Voltage Experimenter
  • **
  • Posts: 55
  • Karma: +0/-0
    • View Profile
Re: mini tesla (hopefully not a fail)
« Reply #2 on: November 04, 2020, 09:48:48 AM »
So what driver should i use ? i tried it with a 555, but it's not acurate at all at that frequency, i even tried it with an arduino, but the square wave...is not a square wave starting from 500kHz.

Offline Zipdox

  • High Voltage Technician
  • ***
  • Posts: 143
  • Karma: +1/-0
    • View Profile
    • Zipdox
Re: mini tesla (hopefully not a fail)
« Reply #3 on: November 04, 2020, 02:12:20 PM »
So what driver should i use ? i tried it with a 555, but it's not acurate at all at that frequency, i even tried it with an arduino, but the square wave...is not a square wave starting from 500kHz.
Using a fixed frequency oscillator is not a good idea. You should be using a driver that takes some kind of feedback.

Offline bogdan

  • High Voltage Experimenter
  • **
  • Posts: 55
  • Karma: +0/-0
    • View Profile
Re: mini tesla (hopefully not a fail)
« Reply #4 on: November 05, 2020, 10:22:12 AM »
Well, i tried the  half-bridge steve ward, but the mosfet drivers just blew up in my face, and after a lot of troubleshooting i could not find anything so i abandoned the project...

Offline Zipdox

  • High Voltage Technician
  • ***
  • Posts: 143
  • Karma: +1/-0
    • View Profile
    • Zipdox
Re: mini tesla (hopefully not a fail)
« Reply #5 on: November 05, 2020, 10:31:33 AM »
Well, i tried the  half-bridge steve ward, but the mosfet drivers just blew up in my face, and after a lot of troubleshooting i could not find anything so i abandoned the project...
Schematic of what you built?

Offline bogdan

  • High Voltage Experimenter
  • **
  • Posts: 55
  • Karma: +0/-0
    • View Profile
Re: mini tesla (hopefully not a fail)
« Reply #6 on: November 06, 2020, 10:22:29 AM »

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2745
  • Karma: +130/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: mini tesla (hopefully not a fail)
« Reply #7 on: November 07, 2020, 04:14:38 AM »
At 835kHz, gate driver chip failure seems likely.  The gate charge of a pair of IRFP460 FETs repeated at 835kHz likely translates to more power dissipation than the gate driver chips can dissipate.

SiC FETs typically have lower gate charge and switch quickly.  That's one option.  Another (or in combination) is to add discrete FET buffers to the gate driver outputs as in many DRSSTC designs, with heat sinks on the buffer FETs.
David Knierim

Offline bogdan

  • High Voltage Experimenter
  • **
  • Posts: 55
  • Karma: +0/-0
    • View Profile
Re: mini tesla (hopefully not a fail)
« Reply #8 on: November 08, 2020, 05:38:37 PM »
Uhm...and in English please ? what does that mean for me ?

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2745
  • Karma: +130/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: mini tesla (hopefully not a fail)
« Reply #9 on: November 08, 2020, 09:27:42 PM »
Sorry, I hadn't paid attention to this topic being in the beginners section.

As you have measured, small designs generally resonate at high frequencies, 835kHz in your case.  Drive electronics are more difficult at high frequencies, especially at high power.  Perhaps a Slayer oscillator running from 24Vdc would be a good starting point for a tiny coil.  I don't have personal experience with Slayer oscillators.  There are some examples on this forum.  Slayer oscillators use a single power transistor and use the secondary ground-return to drive the gate.

Another option for a small coil is to wind it with MANY turns of fine wire.  That's not easy either, but does reduce frequency.

Good luck!
David Knierim

Offline bogdan

  • High Voltage Experimenter
  • **
  • Posts: 55
  • Karma: +0/-0
    • View Profile
Re: mini tesla (hopefully not a fail)
« Reply #10 on: November 10, 2020, 01:40:18 PM »
but a slayer will not give me any sparks, or very small ones, i want to have at least o couple of centimeters with this coil. If i want to make more turns, that means thinner wire, is it a bad thing ?

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2745
  • Karma: +130/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: mini tesla (hopefully not a fail)
« Reply #11 on: November 11, 2020, 04:04:21 AM »
People do get sparks from Slayer driven Tesla coils.  I'd guess that 2cm is achievable, but don't have personal experience.  High frequency can make sparks at lower voltages.

Yes, fine wire does have a down-side.  The series resistance is higher, so secondary Q lower.  However, if you can get the frequency low enough to drive with a normal half-bridge, that may give better performance.

For half-bridge drive, adding a 555 to enable it for short times with longer gaps (low duty cycle) will allow gate-driver chips to survive high frequencies.  That might work even up to 835kHz of your existing coil, but will help even if you rewind to get down to 400kHz or 500kHz.  KaizerPowerElectronics web access isn't working for me at the moment, so I can't double check if enable modulation was already part of the schematic you tried or if there is a similar schematic including such.
David Knierim

Offline bogdan

  • High Voltage Experimenter
  • **
  • Posts: 55
  • Karma: +0/-0
    • View Profile
Re: mini tesla (hopefully not a fail)
« Reply #12 on: November 11, 2020, 06:43:53 PM »
ok, i will look into the thing called slayer on steroids and see what results will i get, i will post them later on, hopefully i get enough time in this weekend. Thank you.

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2745
  • Karma: +130/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: mini tesla (hopefully not a fail)
« Reply #13 on: November 11, 2020, 07:19:24 PM »
The "slayer on steroids" I've seen uses a gate-driver IC, so may have the same overheating issue.

Is a larger secondary diameter possible within your definition of a small coil?  Doubling the diameter will almost halve the frequency using the same wire gauge.
David Knierim

Offline bogdan

  • High Voltage Experimenter
  • **
  • Posts: 55
  • Karma: +0/-0
    • View Profile
Re: mini tesla (hopefully not a fail)
« Reply #14 on: November 12, 2020, 01:42:24 PM »
i can test the circuit on my bigger coil, the frequency of that one is @141kHz, and if everything is ok, i can test the small one.

Offline bogdan

  • High Voltage Experimenter
  • **
  • Posts: 55
  • Karma: +0/-0
    • View Profile
Re: mini tesla (hopefully not a fail)
« Reply #15 on: November 14, 2020, 12:04:33 PM »
So, i built this slayer on steroids circuit, and made a few tests, but, i don't seem to be able to tune it properly, i am posting some waveforms with oscilloscope directly on the coil, and with the power source set at 5V. The current draw is about 2A for all capacitors, except for the test run with no capacitor. Each photo has the capacitor near it. any idea is welcomed.

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2745
  • Karma: +130/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: mini tesla (hopefully not a fail)
« Reply #16 on: November 14, 2020, 07:11:19 PM »
To be helpful, we need the specific schematic you implemented (schematic image or web link to the schematic) and an image or two of your setup showing where the antenna is placed and wired to the slayer oscillator.
David Knierim

Offline bogdan

  • High Voltage Experimenter
  • **
  • Posts: 55
  • Karma: +0/-0
    • View Profile
Re: mini tesla (hopefully not a fail)
« Reply #17 on: November 14, 2020, 07:38:49 PM »
I hope you can tell from these

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2745
  • Karma: +130/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: mini tesla (hopefully not a fail)
« Reply #18 on: November 14, 2020, 09:54:02 PM »
Have you tried reversing the primary coil leads?  Usually one polarity works better, and the opposite polarity may not work at all.

What value is R1?  I can't quite read the color bands in the image.

Oscillation without a capacitor was 213kHz, above your expected 141kHz secondary resonance frequency.  With the smallest capacitor you tried, 0.22uF, frequency was too low, 96kHz.  That implies a smaller capacitor would get closer to 141kHz, around 0.1uF or perhaps a bit lower.

Are the four IRFP140 FETs wired in parallel?  That adds up to more load than TC4426 is designed to drive.  May still work at 141kHz, but definitely won't at 835kHz.  A scope image of the gate waveform would be helpful, together with a drain waveform with the same configuration.
David Knierim

Offline bogdan

  • High Voltage Experimenter
  • **
  • Posts: 55
  • Karma: +0/-0
    • View Profile
Re: mini tesla (hopefully not a fail)
« Reply #19 on: November 15, 2020, 09:11:45 AM »
"Have you tried reversing the primary coil leads?  Usually one polarity works better, and the opposite polarity may not work at all."
yes, i seem to get the best results this way

"What value is R1?"
8.9k, it was the one nearest to my hand :)

"Oscillation without a capacitor was 213kHz, above your expected 141kHz secondary resonance frequency.  With the smallest capacitor you tried, 0.22uF, frequency was too low, 96kHz.  That implies a smaller capacitor would get closer to 141kHz, around 0.1uF or perhaps a bit lower."
now this is strange to me as well, the 141kHz i got with a small capacitor, which sadly is gone. Could that be the reason? and the actual frequency of my coil is actually @210kHz ?? the test i made with the following capacitor shows different results, the capacitor is new, and also the tests are being made with a 12v power supply, also i get around 1cm of starting spark, and i can stretch it at @3cm. If i go lower than 100nF, either my caps are busted or something is wrong because they get really really hot, i will try to find some new ones.

"Are the four IRFP140 FETs wired in parallel?"
yes they are.

High Voltage Forum

Re: mini tesla (hopefully not a fail)
« Reply #19 on: November 15, 2020, 09:11:45 AM »

 


* Recent Topics and Posts

post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
Today at 04:47:35 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
davekni
Today at 03:59:27 AM
post Re: Kaizer VTTC 1
[Vacuum Tube Tesla Coils (VTTC)]
MRMILSTAR
March 28, 2024, 09:15:11 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 28, 2024, 01:01:12 PM
post Re: Big Coil Build Log
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 28, 2024, 05:47:34 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
davekni
March 28, 2024, 04:45:07 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 28, 2024, 04:18:27 AM
post Push Pull VTTC
[Vacuum Tube Tesla Coils (VTTC)]
janno288
March 28, 2024, 01:10:08 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 27, 2024, 10:54:52 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 27, 2024, 11:53:42 AM
post Re: OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 05:14:36 AM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:47:48 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:41:59 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 27, 2024, 12:04:34 AM
post Re: Super flat QCW simulation (does this look reasonable?)
[Dual Resonant Solid State Tesla coils (DRSSTC)]
toooldforthis
March 26, 2024, 11:08:14 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 11:07:20 PM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 10:46:29 PM
post OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 26, 2024, 09:03:43 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 08:46:59 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 26, 2024, 05:02:18 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 03:16:03 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 26, 2024, 01:41:49 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 04:48:22 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 26, 2024, 04:16:37 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 26, 2024, 04:16:24 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 26, 2024, 04:13:02 AM
post Re: CM400 Induction Heater
[Electronic Circuits]
davekni
March 26, 2024, 04:00:43 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
davekni
March 26, 2024, 03:19:18 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
March 26, 2024, 01:50:42 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 08:05:02 PM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 25, 2024, 07:41:29 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 06:45:46 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 05:44:25 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 25, 2024, 04:47:17 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 04:27:22 PM
post Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 25, 2024, 03:57:34 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 25, 2024, 02:06:41 PM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 04:43:25 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
davekni
March 25, 2024, 02:39:40 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 12:47:09 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 24, 2024, 07:36:32 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
Alberto
March 24, 2024, 07:27:24 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 24, 2024, 04:25:23 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 10:47:35 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 09:30:21 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 04:34:31 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 03:04:25 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 01:38:34 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 04:20:03 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 23, 2024, 12:54:30 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 23, 2024, 12:05:57 AM
post capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 22, 2024, 11:45:03 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 22, 2024, 11:30:09 PM
post Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 22, 2024, 10:20:35 PM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Benbmw
March 22, 2024, 09:21:13 PM
post Re: What actually kills MOSFETs?
[Beginners]
AstRii
March 22, 2024, 03:37:11 PM
post What actually kills MOSFETs?
[Beginners]
FPS
March 22, 2024, 05:09:20 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 22, 2024, 03:57:54 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 22, 2024, 02:59:25 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 06:31:42 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
rikkitikkitavi
March 21, 2024, 03:08:01 PM
post Re: [WTS] IGBT, Ferrite, Capacitors, Tools, PSU, Industrial components and parts
[Sell / Buy / Trade]
Mads Barnkob
March 21, 2024, 01:37:32 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Alberto
March 21, 2024, 11:42:07 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 21, 2024, 04:09:14 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 02:15:31 AM
post My Homemade Structural Analysis X-Ray Machine
[X-ray]
Luca c.
March 21, 2024, 01:35:40 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 20, 2024, 10:40:00 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Mads Barnkob
March 20, 2024, 08:03:41 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Mads Barnkob
March 20, 2024, 07:51:57 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 20, 2024, 10:39:47 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 20, 2024, 04:09:59 AM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 20, 2024, 01:13:23 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
March 20, 2024, 12:45:16 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 20, 2024, 12:30:30 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 11:12:24 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:47:49 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:44:19 PM
post Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 19, 2024, 06:52:09 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 19, 2024, 05:02:44 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
Mads Barnkob
March 19, 2024, 05:01:41 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 04:31:02 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 03:59:54 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 06:41:39 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 19, 2024, 04:05:49 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 18, 2024, 09:08:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 09:07:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
Twospoons
March 18, 2024, 08:57:06 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
MRMILSTAR
March 18, 2024, 03:51:33 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:59:46 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:33:25 PM
post Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 11:02:12 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Twospoons
March 18, 2024, 02:36:11 AM
post Re: Best forum for vacuum tube amplifiers?
[General Chat]
Mads Barnkob
March 17, 2024, 07:42:55 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:15:14 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 05:05:04 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
davekni
March 17, 2024, 04:50:51 AM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Twospoons
March 17, 2024, 04:45:17 AM
post 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:17:51 AM
post Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Terry
March 17, 2024, 01:29:32 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 17, 2024, 12:33:06 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal