Author Topic: Tachometer for motorcycle enginge (single cylinder four stroke)  (Read 4487 times)

Offline RocketScienceSmurf

  • High Voltage Technician
  • ***
  • Posts: 125
  • Karma: +0/-0
    • View Profile
A while ago I bought a motorcycle and even though there is not need for it, I thought I would make a small arduino-based "computer" for it to monitor different parameters and one thing that would be neat to have is tachometer to see the current rpm. My plan was to use the ignition pulse before the ignition coil. I took my Hantek 1008 oscilloscope and hooked it up and was very pleased with how the signal looked.  It was way cleaner than I had first thought it would be.

Some time later when I had a plan of how to construct it and also an embryo of arduino code for it I connected everything and things did not work as expected so I hooked up my oscilloscope again and this time things looked a lot different. Even though screenshots suggest the time base is the same it was not. The first time I had the software set too 500ms but then I zoomed in and since the actual bandwidth of the 1008 isn't very good I fooled myself a little bit when I looked at the pictures.

I now realize I need the clean up the signal before I send it to my optocoupler and my question is: What is the best way to filter out the noise/ringing without sacrificing too much of the part of the signal I need?

My idea was to basically construct a "speaker crossover" consisting of two capacitors and an inductor in between creating a third order CLC-filter. The two main components to filter out is the ~2kHz ringing when the coil discharges and a much larger in amplitude ringing or possibly "bounce" happening when the coil is charged and that one looks to be close to 17kHz according to my readings.

Offline petespaco

  • High Voltage Engineer
  • ****
  • Posts: 271
  • Karma: +12/-0
    • View Profile
    • French Creek Valley Activities
Re: Tachometer for motorcycle enginge (single cylinder four stroke)
« Reply #1 on: April 07, 2019, 06:05:31 PM »
How about a Schmitt trigger?  That would clean up the signal.
Google:
schmitt trigger IC sine to square wave
You can get a hex inverting schmitt trigger chip for USD $0.55 from Digikey.

But, if you can find a place farther back in the ignition system, maybe you can find a nice clean  square wave.  Off of the Hall Effect sensor, if it has one.   

I can't really tell from your pictures how high the excursions are.  As you probably know, the Arduino doesn't like voltages higher than 5.

If you really want to get into the whole "ECU" thing, go to:
https://speeduino.com/wiki/index.php/Speeduino

Pete Stanaitis
----------------

Offline RocketScienceSmurf

  • High Voltage Technician
  • ***
  • Posts: 125
  • Karma: +0/-0
    • View Profile
Re: Tachometer for motorcycle enginge (single cylinder four stroke)
« Reply #2 on: April 07, 2019, 07:22:42 PM »
Signal peak-to-peak is just over 20V so I need to get it down to TTL logic levels which I planned to do with an optocoupler.

There is a short negative spike that I thought I could just handle with a single diode. But the problem with the rest of the signal is that I can't just make it to square wave with a schmitt trigger because that would still give me something like 3-4 pulses for every falling edge in the ingition system and that would seriously mess up my arduino math (I use hardware interrupts so it will pick up every single hickup on the signal). Hence the idea to use some capacitors and chokes to smoothen out the signal.

Offline dexter

  • High Voltage Enthusiast
  • *
  • Posts: 32
  • Karma: +2/-0
    • View Profile
Re: Tachometer for motorcycle enginge (single cylinder four stroke)
« Reply #3 on: April 07, 2019, 09:52:08 PM »
Use a monostable with the time constant a bit higher than the length of the noise or a low pass RC between 2 Schmitt trigger gates with the time constant a bit higher than the length of the noise

Offline RocketScienceSmurf

  • High Voltage Technician
  • ***
  • Posts: 125
  • Karma: +0/-0
    • View Profile
Re: Tachometer for motorcycle enginge (single cylinder four stroke)
« Reply #4 on: August 28, 2019, 08:33:57 AM »
Long overdue update to this project. I have been experimenting with a series choke on the ignition pulse and things are looking really good. I also realized that the reason the signal looked so clear at first was that I hit the "roof" of my oscilloscope input voltage. When I hooked everything up with a 20:1 passive attenuator I realized the voltage was actually ~400V which explains my shot optocoupler and constant current driver I was using.

Having realized this I started looking for ways to dampen the ringing and get voltage levels way down. The only thing I had to try at first was a Hammond choke bought for another project. It is specd at 330mH and when I hooked it up with a 680 Ohm resistor to ground I got REALLY nice pulses but the fall time looked a bit too filtered and it is a very bulky choke so I bought a couple of axial ones, one 100mH and one 330uH and tried them out yesterday. They do the trick but I was surprised at how big difference it was between the Hammond one that looks like small transformer and the axial 100mH. The inductance value is about one third but the signal show much more ringing than the big iron core choke. Could this be due to the difference of core material?

The axial one is a Vishay IHD3EB104L

The pic 100mh inductor.gif  shows about 400V but this is due to a software bug and the actual voltage is about 40V
« Last Edit: August 28, 2019, 08:36:25 AM by kamelryttarn »

Offline shrad

  • High Voltage Experimenter
  • **
  • Posts: 54
  • Karma: +1/-0
    • View Profile
Re: Tachometer for motorcycle enginge (single cylinder four stroke)
« Reply #5 on: August 28, 2019, 09:59:34 AM »
hi

I would have a look at a simple wire that you would coil around the ignition wire, like under ten turns, let one end open and the second end to your circuit referenced to ground

you'll have a pulse between the wire end and ground which should be more manageable than 400v, and you can play with the number of turns to get different voltages

Offline RocketScienceSmurf

  • High Voltage Technician
  • ***
  • Posts: 125
  • Karma: +0/-0
    • View Profile
Re: Tachometer for motorcycle enginge (single cylinder four stroke)
« Reply #6 on: August 28, 2019, 11:09:34 AM »
The signal is quite good with this setup. Here is a pic of the signal at the optocoupler. As you can see there is no need for more filtration so I am happy with the setup. I was just surprised with the big difference between the two different types and sizes of inductors. I still don't fully understand what they do and how they work so it is very educational for me to try different components and analyze the different results and try to learn from it. Hopefully the results can also help others.
« Last Edit: August 28, 2019, 01:01:42 PM by kamelryttarn »

Offline shrad

  • High Voltage Experimenter
  • **
  • Posts: 54
  • Karma: +1/-0
    • View Profile
Re: Tachometer for motorcycle enginge (single cylinder four stroke)
« Reply #7 on: August 28, 2019, 11:24:04 AM »
I understand your point, but I would still explore other solutions and especially some that are simpler and require less components, which also means less failure possible and less expensive design

a wire wrapped around the ignition cable will pick up the pulse signal directly at the output of the spark bobbin via capacitive and magnetic coupling and the level should be in the couple volts range at maximum, which could even drive your optocoupler directly with a diode back to back with the optocoupler LED, if lucky

the shaping then can occur at the transistor side of the opto, and there are even optocouplers with a Schmidt trigger output built-in which would simplify your design neven more

just my two cents to suggest alternatives

High Voltage Forum

Re: Tachometer for motorcycle enginge (single cylinder four stroke)
« Reply #7 on: August 28, 2019, 11:24:04 AM »

 


* Recent Topics and Posts

post Re: Big Coil Build Log
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
Today at 05:47:34 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
davekni
Today at 04:45:07 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
Today at 04:18:27 AM
post Push Pull VTTC
[Vacuum Tube Tesla Coils (VTTC)]
janno288
Today at 01:10:08 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 27, 2024, 10:54:52 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 27, 2024, 11:53:42 AM
post Re: OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 05:14:36 AM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:47:48 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:41:59 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 27, 2024, 12:04:34 AM
post Re: Super flat QCW simulation (does this look reasonable?)
[Dual Resonant Solid State Tesla coils (DRSSTC)]
toooldforthis
March 26, 2024, 11:08:14 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 11:07:20 PM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 10:46:29 PM
post OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 26, 2024, 09:03:43 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 08:46:59 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 26, 2024, 05:02:18 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 03:16:03 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 26, 2024, 01:41:49 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 04:48:22 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 26, 2024, 04:16:37 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 26, 2024, 04:16:24 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 26, 2024, 04:13:02 AM
post Re: CM400 Induction Heater
[Electronic Circuits]
davekni
March 26, 2024, 04:00:43 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
davekni
March 26, 2024, 03:19:18 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
March 26, 2024, 01:50:42 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 08:05:02 PM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 25, 2024, 07:41:29 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 06:45:46 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 05:44:25 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 25, 2024, 04:47:17 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 04:27:22 PM
post Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 25, 2024, 03:57:34 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 25, 2024, 02:06:41 PM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 04:43:25 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
davekni
March 25, 2024, 02:39:40 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 12:47:09 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 24, 2024, 07:36:32 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
Alberto
March 24, 2024, 07:27:24 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 24, 2024, 04:25:23 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 10:47:35 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 09:30:21 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 04:34:31 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 03:04:25 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 01:38:34 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 04:20:03 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 23, 2024, 12:54:30 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 23, 2024, 12:05:57 AM
post capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 22, 2024, 11:45:03 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 22, 2024, 11:30:09 PM
post Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 22, 2024, 10:20:35 PM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Benbmw
March 22, 2024, 09:21:13 PM
post Re: What actually kills MOSFETs?
[Beginners]
AstRii
March 22, 2024, 03:37:11 PM
post What actually kills MOSFETs?
[Beginners]
FPS
March 22, 2024, 05:09:20 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 22, 2024, 03:57:54 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 22, 2024, 02:59:25 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 06:31:42 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
rikkitikkitavi
March 21, 2024, 03:08:01 PM
post Re: [WTS] IGBT, Ferrite, Capacitors, Tools, PSU, Industrial components and parts
[Sell / Buy / Trade]
Mads Barnkob
March 21, 2024, 01:37:32 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Alberto
March 21, 2024, 11:42:07 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 21, 2024, 04:09:14 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 02:15:31 AM
post My Homemade Structural Analysis X-Ray Machine
[X-ray]
Luca c.
March 21, 2024, 01:35:40 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 20, 2024, 10:40:00 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Mads Barnkob
March 20, 2024, 08:03:41 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Mads Barnkob
March 20, 2024, 07:51:57 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 20, 2024, 10:39:47 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 20, 2024, 04:09:59 AM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 20, 2024, 01:13:23 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
March 20, 2024, 12:45:16 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 20, 2024, 12:30:30 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 11:12:24 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:47:49 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:44:19 PM
post Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 19, 2024, 06:52:09 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 19, 2024, 05:02:44 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
Mads Barnkob
March 19, 2024, 05:01:41 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 04:31:02 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 03:59:54 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 06:41:39 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 19, 2024, 04:05:49 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 18, 2024, 09:08:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 09:07:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
Twospoons
March 18, 2024, 08:57:06 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
MRMILSTAR
March 18, 2024, 03:51:33 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:59:46 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:33:25 PM
post Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 11:02:12 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Twospoons
March 18, 2024, 02:36:11 AM
post Re: Best forum for vacuum tube amplifiers?
[General Chat]
Mads Barnkob
March 17, 2024, 07:42:55 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:15:14 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 05:05:04 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
davekni
March 17, 2024, 04:50:51 AM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Twospoons
March 17, 2024, 04:45:17 AM
post 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:17:51 AM
post Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Terry
March 17, 2024, 01:29:32 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 17, 2024, 12:33:06 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
March 16, 2024, 08:46:20 PM
post Re: Bleeder resistor for MMC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hydron
March 16, 2024, 08:39:24 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hydron
March 16, 2024, 08:21:44 PM
post Best forum for vacuum tube amplifiers?
[General Chat]
yourboi
March 16, 2024, 08:20:13 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal