Author Topic: RC snubbers  (Read 2690 times)

Offline AstRii

  • High Voltage Engineer
  • ****
  • Posts: 260
  • Karma: +9/-0
  • Czech Technical University in Prague
    • View Profile
    • UHVlab - Tesla Coils | High Voltage | Education
RC snubbers
« on: October 22, 2020, 11:42:26 AM »
Hello!
Lately i've been designing a small mains voltage SSTC for my school.
I ended up using a DRSSTC driver (UD 2.7) because i had one laying around :)
It works well, the driver gets feedback from secondary via CT and it oscillates at about 250kHz.
I'm using 15R resistors to charge the IGBT gates and 5R6 + diode to discharge them. And i'm still getting pretty big voltage spikes. (The coil is tested at only 30VDC so the spikes may be only from C-E capacitance of the IGBTs.)
But still, i want to design an RC snubber to handle these spikes.

When powered from 30VDC:
Without any RC snubbers the voltage on the low side C-E looks like this:

70V spikes!

With 22R + 4.7n:

around 55V spikes.

And with 1R + 22n:

Pretty much no spikes.

Seems like 4.7n is the bare minimum capacity i should use, but with the 22R resistor it heats up a lot (at only 30V, imagine 325V).
But when i switched to 1R + 22n i was expecting the resistor to burn but it was pretty much the same temp. as the 4.7n + 22R snubber.
I read some papers about the power loss on the snubber resistor and they all concluded the same thing: P = 1/2 * C * U^2 * f.
But i don't think this is correct.
Consider Danyk's (DiodeGoneWild) SSTC:

He's using 4.7n and 4.7R at full mains voltage (325V) @100kHz. The formula would predict power loss to be more than 20W, yet it's going fine with one 3W resistor.
Can anyone explain this?

I'm yet to design a suitable RC snubber, i think i cannot go much lower than C=4.7n to reduce the spikes but for that i would need 30kOhms to reduce the power to few Watts (at least according to the P=1/2CU^2f formula).
I have already tried this 4.7n and 30k RC snubber, needless to say.. it didn't do anything :D

« Last Edit: October 22, 2020, 11:52:08 AM by AstRii »
Bc. Marek Novotny
Czech Republic, Czech Technical University in Prague
www.uhvlab.org

Offline T3sl4co1l

  • High Voltage Technician
  • ***
  • Posts: 174
  • Karma: +9/-0
    • View Profile
    • Seven Transistor Labs
Re: RC snubbers
« Reply #1 on: October 22, 2020, 02:07:27 PM »
You need C >= 2.5 Coss and R = sqrt(Lstray / Coss).

Whatever power that dissipates, is whatever it does.

You can also use a RCD clamp or rate snubber, which might dissipate less power, or be more or less sensitive to load conditions?

Evidently your loop has 116nH in it (a resonant frequency of ~3.3MHz with ~20nF loading, and 1 ohm being less than sqrt(L/C)), which is awfully high.  Consider redoing the layout.

Which also puts sqrt(L/C) ~ 5 ohms, so the 4.7 ohms suggested is likely close to optimal.  The peak voltage will be lower for smaller R, but there will be more ringing.  Coss is a few nF for most IGBTs of useful size; it will decrease at higher voltages.  C around 4.7 or 10nF seems good enough.

Tim
« Last Edit: October 22, 2020, 02:10:49 PM by T3sl4co1l »

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2744
  • Karma: +129/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: RC snubbers
« Reply #2 on: October 22, 2020, 07:17:16 PM »
As Tim said, lowering inductance to the H-Bridge is the way to save power.  When you use snubbing with low R and high C, power dissipation is moving into the IGBTs, unless you have sufficient phase-lead and dead-time for resonant H-Bridge output transitions.
David Knierim

Offline Mads Barnkob

  • Administrator
  • Executive Board Member
  • *****
  • Posts: 2267
  • Karma: +71/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: RC snubbers
« Reply #3 on: October 22, 2020, 09:05:22 PM »
We have talked about low voltage testing with you before :)

Look at this old topic about your DRSSTC II: https://highvoltageforum.net/index.php?topic=1122.msg8060#msg8060

Low voltage testing is deceiving! Look at the IGBT datasheet for the capacitance vs Vce graph and you can see that Coes is higher at 30VDC, and lower at 100VDC, Coes is the output capacitance of the IGBT module and this will give you extremely high switching transients when looking at the inverter output voltage. So these switching transients will get lower at higher C-E voltages!
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline AstRii

  • High Voltage Engineer
  • ****
  • Posts: 260
  • Karma: +9/-0
  • Czech Technical University in Prague
    • View Profile
    • UHVlab - Tesla Coils | High Voltage | Education
Re: RC snubbers
« Reply #4 on: October 22, 2020, 10:06:59 PM »
We have talked about low voltage testing with you before :)

Yes you're right, more than once :D
But in this case i don't think it's the C-E capacitance causing the spikes.

My layout looks like this:







I will twist the wires to the primary, that should help me decrease the inductance.

When i'll do some higher voltage tests, i will upload them here:)

Maybe there's not even need for an RC snubber at all, i was only interested in how would someone calculate accurately what's the power dissipation on the snubber resistors, because i don't think it's quadratically proportional to the input voltage as i've seen in some papers about RC snubbers.
Bc. Marek Novotny
Czech Republic, Czech Technical University in Prague
www.uhvlab.org

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2744
  • Karma: +129/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: RC snubbers
« Reply #5 on: October 23, 2020, 12:27:42 AM »
If it's VBus inductance as Tim and I are guessing, scope VBus (high-side collectors).  That depends on layout of the ECB.  If it's like your previous project with traces rather than overlapping planes, then VBus inductance will be high.

If that spike does show up on VBus as I'm guessing, it also implies significant IGBT current at the switching point.  The initial positive spike implies too much phase lead, with IGBTs turning off while still conducting high current.

As Mads pointed out, IGBT capacitances change drastically with voltage.  I agree, this doesn't strike me as primarily due to capacitance.  IGBT capacitance can affect the overshoot shape.  In my experience, it doesn't cause the overshoot waveforms you are showing.

Yes, if nothing else changes, then snubber power goes as VBus^2.  That's because energy in the snubber capacitors is 0.5*C*V^2.
David Knierim

Offline T3sl4co1l

  • High Voltage Technician
  • ***
  • Posts: 174
  • Karma: +9/-0
    • View Profile
    • Seven Transistor Labs
Re: RC snubbers
« Reply #6 on: October 26, 2020, 02:41:18 PM »
Show board layout.

Also, that looks to be a #26 powdered iron core in the GDT, don't expect a great frequency range from it.  It should be hi-mu ferrite, for least loading of the drivers and extended LF range.

Tim

High Voltage Forum

Re: RC snubbers
« Reply #6 on: October 26, 2020, 02:41:18 PM »

 


* Recent Topics and Posts

post Re: Big Coil Build Log
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
Today at 05:47:34 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
davekni
Today at 04:45:07 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
Today at 04:18:27 AM
post Push Pull VTTC
[Vacuum Tube Tesla Coils (VTTC)]
janno288
Today at 01:10:08 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 27, 2024, 10:54:52 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 27, 2024, 11:53:42 AM
post Re: OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 05:14:36 AM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:47:48 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:41:59 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 27, 2024, 12:04:34 AM
post Re: Super flat QCW simulation (does this look reasonable?)
[Dual Resonant Solid State Tesla coils (DRSSTC)]
toooldforthis
March 26, 2024, 11:08:14 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 11:07:20 PM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 10:46:29 PM
post OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 26, 2024, 09:03:43 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 08:46:59 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 26, 2024, 05:02:18 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 03:16:03 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 26, 2024, 01:41:49 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 04:48:22 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 26, 2024, 04:16:37 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 26, 2024, 04:16:24 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 26, 2024, 04:13:02 AM
post Re: CM400 Induction Heater
[Electronic Circuits]
davekni
March 26, 2024, 04:00:43 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
davekni
March 26, 2024, 03:19:18 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
March 26, 2024, 01:50:42 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 08:05:02 PM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 25, 2024, 07:41:29 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 06:45:46 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 05:44:25 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 25, 2024, 04:47:17 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 04:27:22 PM
post Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 25, 2024, 03:57:34 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 25, 2024, 02:06:41 PM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 04:43:25 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
davekni
March 25, 2024, 02:39:40 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 12:47:09 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 24, 2024, 07:36:32 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
Alberto
March 24, 2024, 07:27:24 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 24, 2024, 04:25:23 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 10:47:35 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 09:30:21 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 04:34:31 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 03:04:25 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 01:38:34 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 04:20:03 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 23, 2024, 12:54:30 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 23, 2024, 12:05:57 AM
post capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 22, 2024, 11:45:03 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 22, 2024, 11:30:09 PM
post Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 22, 2024, 10:20:35 PM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Benbmw
March 22, 2024, 09:21:13 PM
post Re: What actually kills MOSFETs?
[Beginners]
AstRii
March 22, 2024, 03:37:11 PM
post What actually kills MOSFETs?
[Beginners]
FPS
March 22, 2024, 05:09:20 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 22, 2024, 03:57:54 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 22, 2024, 02:59:25 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 06:31:42 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
rikkitikkitavi
March 21, 2024, 03:08:01 PM
post Re: [WTS] IGBT, Ferrite, Capacitors, Tools, PSU, Industrial components and parts
[Sell / Buy / Trade]
Mads Barnkob
March 21, 2024, 01:37:32 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Alberto
March 21, 2024, 11:42:07 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 21, 2024, 04:09:14 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 02:15:31 AM
post My Homemade Structural Analysis X-Ray Machine
[X-ray]
Luca c.
March 21, 2024, 01:35:40 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 20, 2024, 10:40:00 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Mads Barnkob
March 20, 2024, 08:03:41 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Mads Barnkob
March 20, 2024, 07:51:57 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 20, 2024, 10:39:47 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 20, 2024, 04:09:59 AM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 20, 2024, 01:13:23 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
March 20, 2024, 12:45:16 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 20, 2024, 12:30:30 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 11:12:24 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:47:49 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:44:19 PM
post Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 19, 2024, 06:52:09 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 19, 2024, 05:02:44 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
Mads Barnkob
March 19, 2024, 05:01:41 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 04:31:02 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 03:59:54 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 06:41:39 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 19, 2024, 04:05:49 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 18, 2024, 09:08:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 09:07:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
Twospoons
March 18, 2024, 08:57:06 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
MRMILSTAR
March 18, 2024, 03:51:33 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:59:46 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:33:25 PM
post Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 11:02:12 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Twospoons
March 18, 2024, 02:36:11 AM
post Re: Best forum for vacuum tube amplifiers?
[General Chat]
Mads Barnkob
March 17, 2024, 07:42:55 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:15:14 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 05:05:04 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
davekni
March 17, 2024, 04:50:51 AM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Twospoons
March 17, 2024, 04:45:17 AM
post 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:17:51 AM
post Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Terry
March 17, 2024, 01:29:32 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 17, 2024, 12:33:06 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
March 16, 2024, 08:46:20 PM
post Re: Bleeder resistor for MMC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hydron
March 16, 2024, 08:39:24 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hydron
March 16, 2024, 08:21:44 PM
post Best forum for vacuum tube amplifiers?
[General Chat]
yourboi
March 16, 2024, 08:20:13 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal