Author Topic: I need a review of my circuit. Polarities specifically  (Read 1852 times)

Offline Patrick

  • High Voltage Enthusiast
  • *
  • Posts: 43
  • Karma: +2/-0
  • Current Project: Pulse Jet
    • View Profile
I need a review of my circuit. Polarities specifically
« on: January 11, 2023, 10:37:53 AM »
Can others review this schematic for polarities of diodes/transistors and the transformer.
The transformer is a three terminal auto-transformer for truck ignition. But I dont know where to put the return HV.
From the primary they both ohm out to 8k Ohms to HV terminal but 0.4 to each other. So I don't know where to ground out the HV sparks too.
Electronics Technologist ll, LBNL.
Mechatronics Technician, A.S.

Offline Rafft

  • High Voltage Technician
  • ***
  • Posts: 148
  • Karma: +3/-0
  • Electronics Hobbyist - HV n00b - FPV Dr0n3 Pil0t
    • View Profile
Re: I need a review of my circuit. Polarities specifically
« Reply #1 on: January 11, 2023, 05:19:00 PM »
3 terminal means it has one 'Gnd' only. The 'primary' is a tapped connection of the secondary (high tension) output.

 Power is applied on the primary coil, power removed and the collapsing magnetic field creates the hv output.
SGTC / SSTC / DR-SSTC / QCW

Offline Patrick

  • High Voltage Enthusiast
  • *
  • Posts: 43
  • Karma: +2/-0
  • Current Project: Pulse Jet
    • View Profile
Re: I need a review of my circuit. Polarities specifically
« Reply #2 on: January 11, 2023, 10:02:00 PM »
I meant with regard to the TVS and the position where the primary and secondary meet. I think its grounded at 2 and 3.
« Last Edit: January 11, 2023, 10:55:19 PM by Patrick »
Electronics Technologist ll, LBNL.
Mechatronics Technician, A.S.

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2680
  • Karma: +127/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: I need a review of my circuit. Polarities specifically
« Reply #3 on: January 12, 2023, 03:37:56 AM »
Quote
Can others review this schematic for polarities of diodes/transistors and the transformer.
The transformer is a three terminal auto-transformer for truck ignition. But I dont know where to put the return HV.
From the primary they both ohm out to 8k Ohms to HV terminal but 0.4 to each other. So I don't know where to ground out the HV sparks too.
Quote
I think its grounded at 2 and 3.
Internal connection could be 2 to 3 or 2 to 4.  Doesn't make very much difference in how you use the coil.  Either way, just return sparks to +15V, or to GND presuming good low-inductance connection of bypass capacitors.

Schematic questions depend on your unspecified goals.  Is this for occasional single sparks when a button is pressed?  Or rapid-fire?  Best way to figure out your own answers is with analog simulation (LTSpice is my favorite, but there are other free tools and on-line simulators available).

D4 is likely to have much lower avalanche energy than IRF1324, so can be left out.
David Knierim

Offline Patrick

  • High Voltage Enthusiast
  • *
  • Posts: 43
  • Karma: +2/-0
  • Current Project: Pulse Jet
    • View Profile
Re: I need a review of my circuit. Polarities specifically
« Reply #4 on: January 12, 2023, 09:30:55 AM »
Quote
Schematic questions depend on your unspecified goals.  Is this for occasional single sparks when a button is pressed?  Or rapid-fire?  Best way to figure out your own answers is with analog simulation (LTSpice is my favorite, but there are other free tools and on-line simulators available).

D4 is likely to have much lower avalanche energy than IRF1324, so can be left out.

O.K. so here is the code and new schematics, it is intended to function as follows: 50 pulses on, 2 seconds off. Ive also added a capacitor across the D-S of the Mosfet is that in a good idea ?
Electronics Technologist ll, LBNL.
Mechatronics Technician, A.S.

Offline Rafft

  • High Voltage Technician
  • ***
  • Posts: 148
  • Karma: +3/-0
  • Electronics Hobbyist - HV n00b - FPV Dr0n3 Pil0t
    • View Profile
Re: I need a review of my circuit. Polarities specifically
« Reply #5 on: January 12, 2023, 10:54:35 AM »
Try it this way.

Refer to webpage for x-former connections
http://mgaguru.com/mgtech/ignition/ig104.htm

Never done any like this(mosfet) & ignition coil, but its the only way possible to drive an ign coil electronically. im also thinking the 'return' or 'gnd' side for hv output is battery+(and not circuit gnd). Just try it. 1N4007 or FR across mosfet. Iron core is supposed to be low freq. Like 50 or 60Hz. Maybe max 400Hz
« Last Edit: January 12, 2023, 11:12:38 AM by Rafft »
SGTC / SSTC / DR-SSTC / QCW

Offline Mike

  • High Voltage Experimenter
  • **
  • Posts: 56
  • Karma: +3/-0
    • View Profile
Re: I need a review of my circuit. Polarities specifically
« Reply #6 on: January 12, 2023, 11:22:44 AM »
I'm not sure if Q1 is connected the way you want. You're using an emitter follower configuration so you will only apply about 4.4V to the gate of your MOSFET. I suspect you wanted to apply 12V so you should be using a common emitter configuration. This will have the effect of inverting your logic (putting D4 high will turn the MOSFET off) but this is easily corrected in your software.

I also noted the LED in your trigger button doesn't have a current limiting resistor. Some switches include one, but not all, so just be wary. Your trigger won't work at all if there's no included resistor.
« Last Edit: January 13, 2023, 10:19:37 AM by Mike »

Offline SteveN87

  • High Voltage Experimenter
  • **
  • Posts: 53
  • Karma: +4/-0
  • FPGA, Software Defined Radio, HV (mainly flyback)
    • View Profile
Re: I need a review of my circuit. Polarities specifically
« Reply #7 on: January 12, 2023, 01:06:06 PM »
The turns ratio of an ignition coil is more like 100:1 than 1000:1.

As connected, D5 will short out the back EMF (great for relay drive circuits, but not so good for this), meaning you'll get about 200V of spark voltage (you would be more likey to get a spark from the forward voltage - about 1500V). Probably just remove D5.

Offline Patrick

  • High Voltage Enthusiast
  • *
  • Posts: 43
  • Karma: +2/-0
  • Current Project: Pulse Jet
    • View Profile
Re: I need a review of my circuit. Polarities specifically
« Reply #8 on: January 13, 2023, 03:25:10 AM »
Quote
As connected, D5 will short out the back EMF (great for relay drive circuits, but not so good for this), meaning you'll get about 200V of spark voltage (you would be more likey to get a spark from the forward voltage - about 1500V). Probably just remove D5.

Yes was thinking the same Ill remove it and try. This circuit just makes me nervous with a delicate microcontroller involved as this breaks one of my cardinal rules:  -Don't trust programmed silicon near HV-  I'm sure the Mosfet and Bipolar transistor will eat a harmful kickback, and I could add a opto-isolator later.

But the timing is a hell of a lot easier than 555 timers which I was limited to all though the late 90's.
Electronics Technologist ll, LBNL.
Mechatronics Technician, A.S.

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2680
  • Karma: +127/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: I need a review of my circuit. Polarities specifically
« Reply #9 on: January 13, 2023, 04:46:36 AM »
Quote
I'm not sure if Q1 is connected the east you want. You're using an emitter follower configuration so you will only apply about 4.4V to the gate if your MOSFET. I suspect you wanted to apply 12V so you should be using a common emitter configuration. This will have the effect of inverting your logic (putting D4 high will turn the MOSFET off) but this is really corrected in your software.
I see 12V going into the processor block.  Had presumed this output was 12V.  If 5V, then this is accurate.  IRF1324 is spec'ed at 10Vgs.

Quote
The turns ratio of an ignition coil is more like 100:1 than 1000:1.
That's true for old ignition coils used with mechanical break points and some new ones with similar electronic control.  However, I've seen other new coils with >=1000:1, I think designed to produce sparks with the forward 12V across primary as well as the reverse voltage at turn-off.  These coils are driven with short pulses (much less than 7ms) of ~20A at 12V.

Quote
As connected, D5 will short out the back EMF (great for relay drive circuits, but not so good for this), meaning you'll get about 200V of spark voltage (you would be more likey to get a spark from the forward voltage - about 1500V). Probably just remove D5.
If 40kV is desired, then 1000:1 isn't enough for this 24V FET IRF1324.  Turn-off voltage will be lower than 15V on-state voltage.  Much of stored magnetic energy will be dissipated in FET avalanche breakdown after turn-off presuming D5 is removed.  If D5 is kept, then energy is dissipated in D5 and in coil primary resistance.  Either way, circuit will be inefficient unless most energy is transferred to secondary during forward FET on-time.

Depends on primary current and inductance whether 20ms is long enough for current to decay.

« Last Edit: January 13, 2023, 04:50:26 AM by davekni »
David Knierim

Offline klugesmith

  • High Voltage Senior
  • *****
  • Posts: 685
  • Karma: +22/-0
    • View Profile
Re: I need a review of my circuit. Polarities specifically
« Reply #10 on: January 13, 2023, 05:10:13 AM »
Yeah, what Dave said about voltage margin.
Consider the "magnetic field collapse" in classical ignition circuit or flyback converter.
How fast does the magnetic field collapse when switch is opened?
If switch turns off instantly, and isn't shunted by a capacitor, then voltage goes to whatever it takes for something to break down in primary or secondary circuit.  THe stored energy has to go somewhere!

Commonly it's the intended spark gap or unintended D-S bypass in MOSFET. (Secondary/primary voltage ratio remains N:1.)
That voltage then determines the rate at which magnetic flux drops to zero. 
« Last Edit: January 13, 2023, 05:12:29 AM by klugesmith »

Offline Patrick

  • High Voltage Enthusiast
  • *
  • Posts: 43
  • Karma: +2/-0
  • Current Project: Pulse Jet
    • View Profile
Re: I need a review of my circuit. Polarities specifically
« Reply #11 on: January 13, 2023, 01:37:54 PM »
Ok Ill continue to post some changes for you guys to see. It sparks more than 23mm every time and if i tune it better i think it will go way past that. But with the IRF540's 0.85 resistance its flaming hot even at 11.5 - 12 volts in about 20 seconds. I dug around and found some IGBTs that are rated for CE 1.7 Volts at 10 or so amps. Ill cut a bigger heatsink and put in the IGBT in a few hours.... need sleep ...... ZZZZzzzzZzzzzZZZzzz... :)
Electronics Technologist ll, LBNL.
Mechatronics Technician, A.S.

Offline petespaco

  • High Voltage Engineer
  • ****
  • Posts: 269
  • Karma: +12/-0
    • View Profile
    • French Creek Valley Activities
Re: I need a review of my circuit. Polarities specifically
« Reply #12 on: January 13, 2023, 06:28:32 PM »
Just a couple of comments, questions:
   What IS the goal of this project?  That is: --- why are you making sparks?

Can you tell how much time the Mosfets are spending in linear mode?  I don't think they like long switching times.

It took me a while to realize that the "auto-transformer" you mentioned in your first post meant "automotive TYPE" of ignition coil  and NOT "autotransformer".
If you are worried about HV pulses sneaking back into your control electronics, why not simply get yourself a "Coil On Plug" or "Coil Near Plug" coil from a more modern ignition system?  They usually accept a 5 volt trigger pulse.
I have many examples of doing this and here is one link:
xW0KdiP5MJY

Here's a much later link:
/>
And, if you are a real "Gluten for Punishment", here's my  playlist for my own "Coil On Plug" monkey business:
https://www.youtube.com/playlist?list=PLVxWen9M87dAFoZqyj3iy_fyBfkWuESRC

Pete Stanaitis
---------------

Offline Patrick

  • High Voltage Enthusiast
  • *
  • Posts: 43
  • Karma: +2/-0
  • Current Project: Pulse Jet
    • View Profile
Re: I need a review of my circuit. Polarities specifically
« Reply #13 on: January 15, 2023, 08:45:18 AM »

   What IS the goal of this project?  That is: --- why are you making sparks?


I need to ignite Methanol, Ether or Gasoline for a pulse jet.
Electronics Technologist ll, LBNL.
Mechatronics Technician, A.S.

Offline RoamingD

  • High Voltage Enthusiast
  • *
  • Posts: 28
  • Karma: +1/-0
  • Self taught 19yo enthusiast
    • View Profile
Re: I need a review of my circuit. Polarities specifically
« Reply #14 on: January 17, 2023, 03:35:47 PM »

   What IS the goal of this project?  That is: --- why are you making sparks?


I need to ignite Methanol, Ether or Gasoline for a pulse jet.
Hello, I am not an expert but what I can say is that you will have a way easier time with using a flyback transformer from an old tv ( you can program the arduino so that when it is triggered, to output a 15-20khz square wave signal to a small bjt that will drive the gate of a mosfet of your choice (preferably something like an irfp 250/260n) connected to a 8 turn primary coil wound on the ferrite core)
 For example, here is a video I found on youtube with an arduino driven flyback transformer
I am getting 5cm arcs from my irfp260n flyback transformer with a 12V power supply and it doesnt get hot with a good heatsink

High Voltage Forum

Re: I need a review of my circuit. Polarities specifically
« Reply #14 on: January 17, 2023, 03:35:47 PM »

 


* Recent Topics and Posts

post LabCoatz Staccato QCW No straight sparks
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
Today at 02:31:59 PM
post UD2.7 Thru Hole Capacitor Selection
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
Today at 02:30:10 PM
post Re: DIY X-RAY generator made of eBay parts
[X-ray]
PhotonLab
February 20, 2024, 03:14:58 PM
post Re: DIY X-RAY generator made of eBay parts
[X-ray]
alan sailer
February 19, 2024, 06:08:05 PM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
February 19, 2024, 03:03:37 PM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
AstRii
February 19, 2024, 04:34:22 AM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
davekni
February 19, 2024, 04:27:28 AM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
AstRii
February 19, 2024, 03:59:51 AM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
davekni
February 19, 2024, 03:45:51 AM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
February 19, 2024, 03:30:09 AM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
AstRii
February 19, 2024, 02:38:49 AM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
February 19, 2024, 01:52:20 AM
post Re: Lathe Restauration
[General Chat]
TMaxElectronics
February 19, 2024, 12:47:27 AM
post Re: VS-GP250SA60S IGBT suitability - no flywheel diode
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
February 18, 2024, 10:32:36 PM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
February 18, 2024, 10:06:58 PM
post Re: VS-GP250SA60S IGBT suitability - no flywheel diode
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hydron
February 18, 2024, 11:43:44 AM
post Re: VS-GP250SA60S IGBT suitability - no flywheel diode
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
February 18, 2024, 03:41:12 AM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
February 18, 2024, 02:43:37 AM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
February 17, 2024, 10:45:17 PM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
February 17, 2024, 10:29:30 PM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
February 17, 2024, 10:20:39 PM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
February 17, 2024, 10:14:20 PM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
February 17, 2024, 08:56:42 PM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
February 17, 2024, 08:52:45 PM
post Re: DIY X-RAY generator made of eBay parts
[X-ray]
PhotonLab
February 16, 2024, 09:20:44 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
February 16, 2024, 03:50:58 AM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
February 16, 2024, 03:27:18 AM
post Re: DIY X-RAY generator made of eBay parts
[X-ray]
klugesmith
February 16, 2024, 01:55:48 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
February 15, 2024, 07:11:20 PM
post Re: DIY X-RAY generator made of eBay parts
[X-ray]
PhotonLab
February 15, 2024, 11:31:42 AM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
davekni
February 15, 2024, 06:01:49 AM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
AstRii
February 15, 2024, 05:13:13 AM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
davekni
February 15, 2024, 04:26:00 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
February 14, 2024, 06:25:45 PM
post Re: DIY X-RAY generator made of eBay parts
[X-ray]
Luca c.
February 14, 2024, 03:33:25 PM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
AstRii
February 14, 2024, 12:57:01 PM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
February 14, 2024, 05:32:30 AM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
davekni
February 14, 2024, 05:22:35 AM
post Re: VS-GP250SA60S IGBT suitability - no flywheel diode
[Dual Resonant Solid State Tesla coils (DRSSTC)]
AstRii
February 14, 2024, 04:34:14 AM
post Re: VS-GP250SA60S IGBT suitability - no flywheel diode
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
February 14, 2024, 03:02:16 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
February 14, 2024, 01:58:17 AM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
AstRii
February 13, 2024, 09:30:40 PM
post DIY X-RAY generator made of eBay parts
[X-ray]
PhotonLab
February 13, 2024, 03:54:23 PM
post VS-GP250SA60S IGBT suitability - no flywheel diode
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
February 13, 2024, 09:57:12 AM
post Re: TNY265 flyback issue
[Transformer (Ferrite Core)]
davekni
February 13, 2024, 03:50:05 AM
post Re: TNY265 flyback issue
[Transformer (Ferrite Core)]
AstRii
February 12, 2024, 07:30:42 PM
post Re: PLL "IHFSSTC" concept and schematic
[Solid State Tesla Coils (SSTC)]
Anders Mikkelsen
February 11, 2024, 10:30:38 PM
post Re: Help finding correct IGBT Module
[General Chat]
rikkitikkitavi
February 11, 2024, 09:41:57 PM
post Re: PLL "IHFSSTC" concept and schematic
[Solid State Tesla Coils (SSTC)]
Lucasww
February 11, 2024, 06:34:35 AM
post Re: TNY265 flyback issue
[Transformer (Ferrite Core)]
davekni
February 10, 2024, 03:55:35 AM
post Help finding correct IGBT Module
[General Chat]
cnichols
February 09, 2024, 09:34:13 PM
post TNY265 flyback issue
[Transformer (Ferrite Core)]
AstRii
February 09, 2024, 06:45:46 PM
post Re: Help Sourcing or Debugging My Small HV Module
[Transformer (Ferrite Core)]
michaelrcolton
February 08, 2024, 07:04:07 PM
post ESAB Bantam TBH 140 Welder Restoration
[Laboratories, Equipment and Tools]
Mads Barnkob
February 08, 2024, 06:47:35 PM
post Re: Anyone used iCCFL.com?
[Transformer (Ferrite Core)]
FPS
February 08, 2024, 12:27:47 AM
post Re: PLL "IHFSSTC" concept and schematic
[Solid State Tesla Coils (SSTC)]
Anders Mikkelsen
February 07, 2024, 09:49:11 PM
post Re: Anyone know of a good variable driver?
[Beginners]
NyaaX_X
February 07, 2024, 04:48:02 PM
post Re: Anyone know of a good variable driver?
[Beginners]
FPS
February 07, 2024, 08:17:37 AM
post Re: How much power?
[Spark Gap Tesla Coils (SGTC)]
Terry
February 06, 2024, 10:51:35 PM
post Re: OCXO Reference devolopment - or a story about scaleability
[Radio Frequency]
Mads Barnkob
February 06, 2024, 07:29:29 PM
post Re: Anyone used iCCFL.com?
[Transformer (Ferrite Core)]
MRMILSTAR
February 05, 2024, 05:18:33 AM
post Re: Anyone know of a good variable driver?
[Beginners]
Mads Barnkob
February 04, 2024, 09:16:25 PM
post Re: PLL "IHFSSTC" concept and schematic
[Solid State Tesla Coils (SSTC)]
davekni
February 04, 2024, 09:13:36 PM
post Anyone used iCCFL.com?
[Transformer (Ferrite Core)]
FPS
February 04, 2024, 09:00:30 PM
post Re: Anyone know of a good variable driver?
[Beginners]
FPS
February 04, 2024, 08:56:14 PM
post Re: OCXO Reference devolopment - or a story about scaleability
[Radio Frequency]
Da_Stier
February 04, 2024, 08:18:01 PM
post Re: Anyone know of a good variable driver?
[Beginners]
Mads Barnkob
February 04, 2024, 08:04:36 PM
post OCXO Reference devolopment - or a story about scaleability
[Radio Frequency]
Da_Stier
February 04, 2024, 07:56:55 PM
post Re: PLL "IHFSSTC" concept and schematic
[Solid State Tesla Coils (SSTC)]
Lucasww
February 04, 2024, 08:45:53 AM
post Anyone know of a good variable driver?
[Beginners]
FPS
February 04, 2024, 12:56:52 AM
post Re: looking for a pll sstc schematic with gate driver ic.
[Solid State Tesla Coils (SSTC)]
yourboi
February 03, 2024, 07:01:12 PM
post Re: SSTC bus inductance
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
February 03, 2024, 08:04:29 AM
post Re: SSTC bus inductance
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
February 03, 2024, 06:01:12 AM
post Re: is there a standard pinout of optical audio output connectors?
[Electronic Circuits]
Rafft
February 02, 2024, 05:04:44 PM
post SSTC bus inductance
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
February 02, 2024, 08:34:56 AM
post Re: How much power?
[Spark Gap Tesla Coils (SGTC)]
klugesmith
February 01, 2024, 07:03:41 PM
post Does anyone have a 3d print form for a spiral primary on 4" pvc?
[Solid State Tesla Coils (SSTC)]
yourboi
February 01, 2024, 06:23:45 PM
post Re: How much power?
[Spark Gap Tesla Coils (SGTC)]
Mads Barnkob
February 01, 2024, 07:53:53 AM
post Re: How much power?
[Spark Gap Tesla Coils (SGTC)]
klugesmith
January 31, 2024, 11:43:32 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
Ranni81
January 31, 2024, 08:03:40 PM
post Re: How much power?
[Spark Gap Tesla Coils (SGTC)]
Hysteresis
January 31, 2024, 03:34:48 PM
post Re: How much power?
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
January 31, 2024, 05:08:10 AM
post Re: How much power?
[Spark Gap Tesla Coils (SGTC)]
Mads Barnkob
January 30, 2024, 10:17:45 PM
post How much power?
[Spark Gap Tesla Coils (SGTC)]
Terry
January 30, 2024, 08:07:39 PM
post Ultrasonic Plastic Welding experiments with TA-40CS transducer
[Transformer (Ferrite Core)]
davekni
January 28, 2024, 11:37:30 PM
post Re: is there a standard pinout of optical audio output connectors?
[Electronic Circuits]
yourboi
January 28, 2024, 03:07:12 AM
post Re: First time DRSSTC Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
January 27, 2024, 02:27:29 PM
post Re: Lathe Restauration
[General Chat]
Mads Barnkob
January 27, 2024, 01:26:34 PM
post Re: Determine output voltage of DRSSTC
[General Chat]
Mads Barnkob
January 27, 2024, 01:15:51 PM
post Re: is there a standard pinout of optical audio output connectors?
[Electronic Circuits]
Mads Barnkob
January 27, 2024, 01:13:29 PM
post Determine output voltage of DRSSTC
[General Chat]
Pavol
January 27, 2024, 11:35:35 AM
post is there a standard pinout of optical audio output connectors?
[Electronic Circuits]
yourboi
January 27, 2024, 01:47:13 AM
post Re: First time DRSSTC Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
AstRii
January 26, 2024, 11:26:11 PM
post Re: First time DRSSTC Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
January 26, 2024, 08:24:30 PM
post Re: Next Gen DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Netzpfuscher
January 26, 2024, 05:19:18 PM
post Re: Anyone had success using analogue/digital HV panel meters?
[Beginners]
MRMILSTAR
January 26, 2024, 04:28:38 PM
post Re: Anyone had success using analogue/digital HV panel meters?
[Beginners]
Luca c.
January 26, 2024, 03:34:10 PM
post Re: Anyone had success using analogue/digital HV panel meters?
[Beginners]
FPS
January 26, 2024, 11:49:48 AM
post Re: Anyone had success using analogue/digital HV panel meters?
[Beginners]
TizianoBll
January 26, 2024, 11:04:37 AM
post Re: Next Gen DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
January 26, 2024, 06:26:58 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal