Author Topic: Full Bridge Inverter from bits and pieces  (Read 5459 times)

Offline Thunderstruck

  • High Voltage Experimenter
  • **
  • Posts: 68
  • Karma: +1/-0
    • View Profile
Full Bridge Inverter from bits and pieces
« on: April 07, 2019, 08:27:39 AM »
Originally I wanted to build Profdc9’s full bridge inverter, I also wanted to build it using parts listed in the BOM, I even filled a shopping cart at Mouser with all the necessary parts - about $120 worth...

Then the power and gas bills came together...  :-\

So, because I have to act as a responsible adult (BORING), hobby has to wait for funding to be available again.

Then I remebered that I have some bits n pieces left over from my first SSTC attempt that might work together to make a functioning bridge using Profdc9’s full bridge PCB.

I have:
- 4 IRFP460 FETs
- 4 MUR860 Fast Diodes
- 4 WIMA MKP10 0.68uF 630V Polypropylene Caps

I think that there is enough parts here to make a circuit based on Steve Ward’s mini SSTC half bridge inverter, but full bridge instead and using above mentioned PCB.
Maybe my thinking is wrong, but to me it looks like just a matter of doubling the number of the components, and of course driving the FETS in the correct sequence.

Drive would be provided by Profdc9’s SSTC Driver.

So far I mounted the parts together, not exacly as one would expect, but if everything works well I reckon it will make a neater build.

I cannot figure a couple things, one is due to inexperience in interpreting component data sheets:

1. What is the maximum Gate voltage on IRFP460 - I gather its about 10V but not sure
2. GDT from the driver outputs about 34V peak to peak, which is way too high for IRFP460,   
    how do you bring the voltage down so it can be handled by the gate ? Only way I can think of is
    changing primary to secondary winding ratio.

I’d appreciate if someone could help with this - even if you tell me that this contraption will never work the way I imagined.

Image 1 Snip from Steve Ward’s schematic that i want to duplicate in a full bridge configuration
Image 2 Parts on hand
Image 3 Build so far - TVS diodes are bent like that because I wanted to put them under the board, but later realised it wouldn’t work  ::)
Image 4 This way FETS get a huge heatsink that can later serve as a base for the coil - of course keeping in mind that the transistors must be isolated from the heatsink, otherwise there will be a lot of angry Pixies in that sink, waiting to bite.




Offline Fumeaux

  • High Voltage Experimenter
  • **
  • Posts: 82
  • Karma: +7/-0
    • View Profile
Re: Full Bridge Inverter from bits and pieces
« Reply #1 on: April 07, 2019, 08:50:09 AM »
I cannot figure a couple things, one is due to inexperience in interpreting component data sheets:

1. What is the maximum Gate voltage on IRFP460 - I gather its about 10V but not sure
2. GDT from the driver outputs about 34V peak to peak, which is way too high for IRFP460, how do you bring the voltage down so it can be handled by the gate ? Only way I can think of is changing primary to secondary winding ratio.

1) The gatevoltage for the IRFP460 is +-20V. (+- mean you can put everything between 20V and -20V on the gate)
* 91237.pdf
2) 34Vpp (Peak to Peak) means 17Vp (one Peak) or +-17V which is smaller than +-20V. So you are fine as it is.


You could bring it down either by lowering the secondary turns or lowering the gdt driver voltage (which may or may not be possible).

Offline Thunderstruck

  • High Voltage Experimenter
  • **
  • Posts: 68
  • Karma: +1/-0
    • View Profile
Re: Full Bridge Inverter from bits and pieces
« Reply #2 on: April 07, 2019, 08:58:01 AM »
I cannot figure a couple things, one is due to inexperience in interpreting component data sheets:

1. What is the maximum Gate voltage on IRFP460 - I gather its about 10V but not sure
2. GDT from the driver outputs about 34V peak to peak, which is way too high for IRFP460, how do you bring the voltage down so it can be handled by the gate ? Only way I can think of is changing primary to secondary winding ratio.

1) The gatevoltage for the IRFP460 is +-20V. (+- mean you can put everything between 20V and -20V on the gate)
* 91237.pdf
2) 34Vpp (Peak to Peak) means 17Vp (one Peak) or +-17V which is smaller than +-20V. So you are fine as it is.

You could bring it down either by lowering the secondary turns or lowering the gdt driver voltage (which may or may not be possible).

Two birds with one stone ! Thanks Fumeaux !
So, Vgs is what I needed... well I suppose now I know  :)

I tried lowering GDT driver voltage - it doesn’t like it, gets emotional very quickly
But, GDT output voltage is not an issue any more.

Offline Laci

  • High Voltage Engineer
  • ****
  • Posts: 214
  • Karma: +6/-0
    • View Profile
Re: Full Bridge Inverter from bits and pieces
« Reply #3 on: April 07, 2019, 09:01:39 AM »
MUR860s are not TVS diodes,but ultrafast recovery and works as freewheeling diodes. ;)

Offline Thunderstruck

  • High Voltage Experimenter
  • **
  • Posts: 68
  • Karma: +1/-0
    • View Profile
Re: Full Bridge Inverter from bits and pieces
« Reply #4 on: April 07, 2019, 09:05:48 AM »
MUR860s are not TVS diodes,but ultrafast recovery and works as freewheeling diodes. ;)

Yes, that... what you said  ;D

But they deal with the same thing, right ? Feedback from an inductive load ?

Offline Laci

  • High Voltage Engineer
  • ****
  • Posts: 214
  • Karma: +6/-0
    • View Profile
Re: Full Bridge Inverter from bits and pieces
« Reply #5 on: April 07, 2019, 09:17:34 AM »
TVS diodes are more likely used in high inductance bridge design,where high voltages are generated due to parasitic inductances,which they clamp to a safe level.

Offline Fumeaux

  • High Voltage Experimenter
  • **
  • Posts: 82
  • Karma: +7/-0
    • View Profile
Re: Full Bridge Inverter from bits and pieces
« Reply #6 on: April 07, 2019, 09:32:35 AM »
MUR860s are not TVS diodes,but ultrafast recovery and works as freewheeling diodes. ;)

Yes, that... what you said  ;D

But they deal with the same thing, right ? Feedback from an inductive load ?

Point is: they are not ideal, but I do think that they are good enough for a SSTC. TVS diodes are essential for DRSSTCs or I guess when you want a 3kW SSTC, but most schematics online for normal SSTCs don't feature TVS diodes.

Offline Teravolt

  • High Voltage Technician
  • ***
  • Posts: 125
  • Karma: +2/-0
    • View Profile
Re: Full Bridge Inverter from bits and pieces
« Reply #7 on: April 09, 2019, 05:01:38 AM »
the diode conducts only one direction and a tvs conducts in two directions like a big Zenar diode. The reason for them is to protect the internal diode in the mosfet during times of hard switching. If your switching ZCS timing is in phase and or on time they will never conduct.

High Voltage Forum

Re: Full Bridge Inverter from bits and pieces
« Reply #7 on: April 09, 2019, 05:01:38 AM »

 


* Recent Topics and Posts

post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
Today at 04:47:35 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
davekni
Today at 03:59:27 AM
post Re: Kaizer VTTC 1
[Vacuum Tube Tesla Coils (VTTC)]
MRMILSTAR
March 28, 2024, 09:15:11 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 28, 2024, 01:01:12 PM
post Re: Big Coil Build Log
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 28, 2024, 05:47:34 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
davekni
March 28, 2024, 04:45:07 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 28, 2024, 04:18:27 AM
post Push Pull VTTC
[Vacuum Tube Tesla Coils (VTTC)]
janno288
March 28, 2024, 01:10:08 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 27, 2024, 10:54:52 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 27, 2024, 11:53:42 AM
post Re: OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 05:14:36 AM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:47:48 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:41:59 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 27, 2024, 12:04:34 AM
post Re: Super flat QCW simulation (does this look reasonable?)
[Dual Resonant Solid State Tesla coils (DRSSTC)]
toooldforthis
March 26, 2024, 11:08:14 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 11:07:20 PM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 10:46:29 PM
post OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 26, 2024, 09:03:43 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 08:46:59 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 26, 2024, 05:02:18 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 03:16:03 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 26, 2024, 01:41:49 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 04:48:22 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 26, 2024, 04:16:37 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 26, 2024, 04:16:24 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 26, 2024, 04:13:02 AM
post Re: CM400 Induction Heater
[Electronic Circuits]
davekni
March 26, 2024, 04:00:43 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
davekni
March 26, 2024, 03:19:18 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
March 26, 2024, 01:50:42 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 08:05:02 PM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 25, 2024, 07:41:29 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 06:45:46 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 05:44:25 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 25, 2024, 04:47:17 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 04:27:22 PM
post Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 25, 2024, 03:57:34 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 25, 2024, 02:06:41 PM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 04:43:25 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
davekni
March 25, 2024, 02:39:40 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 12:47:09 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 24, 2024, 07:36:32 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
Alberto
March 24, 2024, 07:27:24 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 24, 2024, 04:25:23 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 10:47:35 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 09:30:21 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 04:34:31 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 03:04:25 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 01:38:34 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 04:20:03 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 23, 2024, 12:54:30 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 23, 2024, 12:05:57 AM
post capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 22, 2024, 11:45:03 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 22, 2024, 11:30:09 PM
post Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 22, 2024, 10:20:35 PM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Benbmw
March 22, 2024, 09:21:13 PM
post Re: What actually kills MOSFETs?
[Beginners]
AstRii
March 22, 2024, 03:37:11 PM
post What actually kills MOSFETs?
[Beginners]
FPS
March 22, 2024, 05:09:20 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 22, 2024, 03:57:54 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 22, 2024, 02:59:25 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 06:31:42 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
rikkitikkitavi
March 21, 2024, 03:08:01 PM
post Re: [WTS] IGBT, Ferrite, Capacitors, Tools, PSU, Industrial components and parts
[Sell / Buy / Trade]
Mads Barnkob
March 21, 2024, 01:37:32 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Alberto
March 21, 2024, 11:42:07 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 21, 2024, 04:09:14 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 02:15:31 AM
post My Homemade Structural Analysis X-Ray Machine
[X-ray]
Luca c.
March 21, 2024, 01:35:40 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 20, 2024, 10:40:00 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Mads Barnkob
March 20, 2024, 08:03:41 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Mads Barnkob
March 20, 2024, 07:51:57 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 20, 2024, 10:39:47 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 20, 2024, 04:09:59 AM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 20, 2024, 01:13:23 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
March 20, 2024, 12:45:16 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 20, 2024, 12:30:30 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 11:12:24 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:47:49 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:44:19 PM
post Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 19, 2024, 06:52:09 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 19, 2024, 05:02:44 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
Mads Barnkob
March 19, 2024, 05:01:41 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 04:31:02 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 03:59:54 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 06:41:39 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 19, 2024, 04:05:49 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 18, 2024, 09:08:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 09:07:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
Twospoons
March 18, 2024, 08:57:06 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
MRMILSTAR
March 18, 2024, 03:51:33 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:59:46 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:33:25 PM
post Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 11:02:12 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Twospoons
March 18, 2024, 02:36:11 AM
post Re: Best forum for vacuum tube amplifiers?
[General Chat]
Mads Barnkob
March 17, 2024, 07:42:55 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:15:14 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 05:05:04 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
davekni
March 17, 2024, 04:50:51 AM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Twospoons
March 17, 2024, 04:45:17 AM
post 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:17:51 AM
post Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Terry
March 17, 2024, 01:29:32 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 17, 2024, 12:33:06 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal