Author Topic: Want to build HV HF oscilloscope probe.  (Read 2176 times)

Offline Domo

  • High Voltage Enthusiast
  • *
  • Posts: 11
  • Karma: +0/-0
    • View Profile
Want to build HV HF oscilloscope probe.
« on: May 18, 2024, 09:46:17 PM »
Hello all..

I would like to build a HV and HF probe, that can measure up to around 30kv (TV flyback output).
Since the output  (by calculation) of the flyback is around 3-4 mA, i didn't want the load of probe to draw much current, so I decided to use 20 100MOhm resistors (total of 2 G Ohm). This also was influenced by use of 1/2 watt resistors. Output would be 1000:1, so measuring 10kV would show up as 10V.  By calculations, probe would draw around 15 uA.


I have not yet build it, it is only in simulation, but i am already running into a problem. From the probe to oscilloscope, I would be using coax cable, and I am aware that it has average parasitic capacitance of 66.7pF per meter. When i add that to the simulation, sine wave does not rise more than 3Vpp. Changing values between output of probe and ground does not increase the sinewave amplitude, How can I compensate this?




Offline Twospoons

  • High Voltage Engineer
  • ****
  • Posts: 244
  • Karma: +6/-0
    • View Profile
Re: Want to build HV HF oscilloscope probe.
« Reply #1 on: May 18, 2024, 11:30:11 PM »
Short answer is you need to add capacitance across your 2Gohm resistor to form a capacitive divider than matches your resistive divider, which in your example will be 66fF, or 1.3pF across each 100Mohm resistor . 

Also I suggest you run your sim as an AC analysis - then you will see the frequency response of your probe, and why the capacitive compensation is necessary.

Here's a couple of resources you should find useful :

Oscilloscope Probe Circuits (tektronix) https://w140.com/tekwiki/images/6/62/062-1146-00.pdf   (I would attach the file but it exceeds the file size limit.)
* 100kv_probe.pdf
« Last Edit: May 18, 2024, 11:38:07 PM by Twospoons »

Offline Domo

  • High Voltage Enthusiast
  • *
  • Posts: 11
  • Karma: +0/-0
    • View Profile
Re: Want to build HV HF oscilloscope probe.
« Reply #2 on: May 19, 2024, 02:05:05 AM »
Very good information on attachment.. Thank you.

Offline klugesmith

  • High Voltage Senior
  • *****
  • Posts: 741
  • Karma: +22/-0
    • View Profile
Re: Want to build HV HF oscilloscope probe.
« Reply #3 on: May 19, 2024, 02:48:22 AM »
Also be sure to mind the voltage rating of your resistors.   Look for ones that are called "high voltage resistors".

Most ordinary half-watt axial lead resistors have maximum rated voltage of 350 V.
https://www.seielect.com/catalog/sei-cf_cfm.pdf
A typical resistor product series has a wide range of ohm values, all with the same max power and max voltage.
For R values near the high end,  the voltage limit gets you before the power limit.
Large voltage overloads don't typically cause sparks or smoke, but they can cause resistance change (reversible or not) and long term degradation of the ohmic material.

[edit] your low side resistor is shown as 1Meg + 15.5k, for DC attenuation of about 1/2000 instead of 1/1000.
I guess that's what you want.   The simulation without capacitors shows RMS voltage of 10 kV in, 5 V out.
Lets see if your AC analysis, with 66.7 pF capacitor in parallel with low side R, gives you a 2.35 kHz lowpass filter.
At 10 kHz most of the current goes through the capacitor.

As twospoons said, to get flat frequency response you need a capacitive divider that matches the resistive divider.
Then at 10 kHz, the probe's input capacitance will draw a lot more current than its input resistance.
« Last Edit: May 19, 2024, 03:24:41 AM by klugesmith »

Offline Twospoons

  • High Voltage Engineer
  • ****
  • Posts: 244
  • Karma: +6/-0
    • View Profile
Re: Want to build HV HF oscilloscope probe.
« Reply #4 on: May 19, 2024, 05:08:46 AM »
There is an argument to be made for putting a cable-driving buffer in your probe. That way you can reduce the capacitance of your probe and extend the frequency range without unduly loading whatever you are testing.  It also means you can correctly terminate your cable to avoid ringing.

What upper frequency are you aiming for?

Offline Domo

  • High Voltage Enthusiast
  • *
  • Posts: 11
  • Karma: +0/-0
    • View Profile
Re: Want to build HV HF oscilloscope probe.
« Reply #5 on: May 19, 2024, 07:34:09 PM »
Also be sure to mind the voltage rating of your resistors.   Look for ones that are called "high voltage resistors".

The resistors I want to get are from digikey, HVA05FA100M. Datasheet says max voltage is 3500V. They are 1/2 watt, so it should withstand around 30KV input.

What upper frequency are you aiming for?

This is a project to measure output of TV flyback transformers, so average around 30KV output at 15.7 kHz. In simulation I tested with 10kv RMS @ 10 kHz, and those were arbitrary numbers for easier calculations.

Offline Domo

  • High Voltage Enthusiast
  • *
  • Posts: 11
  • Karma: +0/-0
    • View Profile
Re: Want to build HV HF oscilloscope probe.
« Reply #6 on: May 19, 2024, 08:53:37 PM »
So it appears that AC probe would be not easy using coax cable... Can I just use banana-to-bnc cables? It would eliminate parasitic capacitance. Besides, tv flybacks have pulsed DC, and that is the only thing I would be using it for, to measure 30kV, with minimal current draw.

Now, a new dilemma appeared.. Oscilloscope input impedance is 15pF and 1M Ohm (both to ground), and the current coming out of the voltage divider is so low, that the 15pF is not charging fast enough, and simulation show an RC charge time instead of DC pulses... dang, back to drawing board..

I have tested few circuits in simulator, and I cannot find any work properly..

Edit:
If I am to only use  for flyback transformers, then I guess i will have to compromise any only use for one purpose. I won't be using coax, just banana-to-coax conector.

Signal input to probe is 30kV, 15.7 kHz.


If the output of transformer is 30 kV pulsed DC (0-30 kv), then the output will be 3Vpp (+1.5 to -1.5).



Before I build this i would welcome comments and suggestions.
« Last Edit: May 19, 2024, 11:54:59 PM by Domo »

Offline Twospoons

  • High Voltage Engineer
  • ****
  • Posts: 244
  • Karma: +6/-0
    • View Profile
Re: Want to build HV HF oscilloscope probe.
« Reply #7 on: May 20, 2024, 01:20:42 AM »
No-one suggested an AC probe.  This was about the simulation you are running - do an AC analysis instead of a transient analysis. The result should be a plot of gain vs frequency. Ideally you want the gain curve to be flat over the frequency range of interest. In your case I'd suggest a bandwidth of about 100kHz, which would cover the 5th harmonic of your TV flyback 15kHz.

Quote
Can I just use banana-to-bnc cables? It would eliminate parasitic capacitance.
No. It wont eliminate parasitic C, only change it in an unpredictable way. It would also increase your parasitic inductance.  You'd do better to add a buffer amp, if driving the cable and scope input is  too hard.

What simulator are you using?



Offline klugesmith

  • High Voltage Senior
  • *****
  • Posts: 741
  • Karma: +22/-0
    • View Profile
Re: Want to build HV HF oscilloscope probe.
« Reply #8 on: May 21, 2024, 09:43:39 PM »
If you just want to know the peak voltage, why not get a HV rectifier and charge a small HV capacitor,
to a voltage that can be measured with ordinary kilovoltmeter probe?


If you want to see the waveshape on oscilloscope, can you fit a test winding of a few turns onto the core of your flyback?

Offline Domo

  • High Voltage Enthusiast
  • *
  • Posts: 11
  • Karma: +0/-0
    • View Profile
Re: Want to build HV HF oscilloscope probe.
« Reply #9 on: June 03, 2024, 07:41:41 AM »
No-one suggested an AC probe.  This was about the simulation you are running - do an AC analysis instead of a transient analysis. The result should be a plot of gain vs frequency. Ideally you want the gain curve to be flat over the frequency range of interest. In your case I'd suggest a bandwidth of about 100kHz, which would cover the 5th harmonic of your TV flyback 15kHz.


This is taken from output of the probe / input to oscilloscope.

What simulator are you using?

NI Miltisim 13

Sorry for late reply.. busy at home..

Offline Twospoons

  • High Voltage Engineer
  • ****
  • Posts: 244
  • Karma: +6/-0
    • View Profile
Re: Want to build HV HF oscilloscope probe.
« Reply #10 on: June 03, 2024, 11:13:26 PM »
Can I suggest replotting using dB on the Y axis, and only plot the voltage. Putting V and I on the same graph creates a scaling issue that makes it hard to interpret the results.  We're interested in seeing the -3dB point.  You should also plot the X- axis  using a log scale, covering 10Hz to 1MHz.

Offline Domo

  • High Voltage Enthusiast
  • *
  • Posts: 11
  • Karma: +0/-0
    • View Profile
Re: Want to build HV HF oscilloscope probe.
« Reply #11 on: June 05, 2024, 04:58:35 AM »
Can I suggest replotting using dB on the Y axis, and only plot the voltage. Putting V and I on the same graph creates a scaling issue that makes it hard to interpret the results.  We're interested in seeing the -3dB point.  You should also plot the X- axis  using a log scale, covering 10Hz to 1MHz.

Frequency in LOG,
Amplitude in dB,
10 Hz - 1 MHz.

Offline Twospoons

  • High Voltage Engineer
  • ****
  • Posts: 244
  • Karma: +6/-0
    • View Profile
Re: Want to build HV HF oscilloscope probe.
« Reply #12 on: June 05, 2024, 07:04:45 AM »
Much easier to interpret!
So you currently have a bandwidth that covers 400Hz to ~30kHz.  Which is why your square waves look messed up.
Now if you get rid of C1 and instead put a capacitor across each 5Meg resistor to match the division ratio you have with your resistors, you can greatly extend and flatten the response of your probe.  In practice there will be stray capacitance from your divider resistors to ground that you will have to account for.   Achieving 1MHz bandwidth on a real life probe shouldn't be to hard with a bit of care in construction.

Simple diagram of the end goal, where the ratio of the capacitors matches the ratio of the resistors :

High Voltage Forum

Re: Want to build HV HF oscilloscope probe.
« Reply #12 on: June 05, 2024, 07:04:45 AM »

 


* Recent Topics and Posts

post Re: Problem with SSTC
[Solid State Tesla Coils (SSTC)]
Nunu00
July 12, 2024, 10:17:36 PM
post Making a HV prove
[Electronic Circuits]
Alberto
July 12, 2024, 09:01:08 PM
post Re: Problem with SSTC
[Solid State Tesla Coils (SSTC)]
davekni
July 12, 2024, 01:33:37 AM
post Re: Problem with SSTC
[Solid State Tesla Coils (SSTC)]
Nunu00
July 12, 2024, 12:17:32 AM
post Re: Restoring a Rogowski coil calibrator
[Capacitor Banks]
davekni
July 11, 2024, 07:38:26 PM
post Re: Restoring a Rogowski coil calibrator
[Capacitor Banks]
klugesmith
July 11, 2024, 06:30:00 PM
post LOD No Double Resonant SSTC?
[Solid State Tesla Coils (SSTC)]
ColinHeath
July 11, 2024, 06:08:30 PM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
July 11, 2024, 12:24:56 PM
post Re: Strange QCW Streamer Behavior
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 11, 2024, 06:42:23 AM
post Re: Syntherrupter Lightsaber Sender Programming
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Cameron Prince
July 11, 2024, 05:46:07 AM
post Syntherrupter Lightsaber Sender Programming
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Cameron Prince
July 11, 2024, 05:26:51 AM
post Re: Strange QCW Streamer Behavior
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
July 11, 2024, 02:50:54 AM
post Strange QCW Streamer Behavior
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Coupling
July 11, 2024, 12:59:55 AM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic Circuits]
petespaco
July 10, 2024, 07:10:34 PM
post Re: Understanding and tracking upper and lower poles of QCW DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 10, 2024, 06:52:42 PM
post Re: Understanding and tracking upper and lower poles of QCW DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Anders Mikkelsen
July 10, 2024, 06:28:19 PM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Alex_1996
July 10, 2024, 01:34:09 PM
post Re: Silicon(e) plasma
[General Chat]
alan sailer
July 10, 2024, 12:09:06 AM
post Re: Problem with SSTC
[Solid State Tesla Coils (SSTC)]
Nunu00
July 09, 2024, 11:52:00 PM
post Understanding and tracking upper and lower poles of QCW DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
July 09, 2024, 07:37:22 PM
post Re: Silicon(e) plasma
[General Chat]
MechatEng2023
July 09, 2024, 07:30:05 PM
post Re: UD2.7C outputs very odd single square wave pulses
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 09, 2024, 03:30:49 AM
post Re: UD2.7C outputs very odd single square wave pulses
[Dual Resonant Solid State Tesla coils (DRSSTC)]
verliebt_in_neukölln17
July 09, 2024, 12:51:02 AM
post Re: UD2.7C outputs very odd single square wave pulses
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 08, 2024, 11:30:44 PM
post Re: Why so cheap?
[General Chat]
alan sailer
July 08, 2024, 10:57:10 PM
post UD2.7C outputs very odd single square wave pulses
[Dual Resonant Solid State Tesla coils (DRSSTC)]
verliebt_in_neukölln17
July 08, 2024, 10:21:01 PM
post Why so cheap?
[General Chat]
MRMILSTAR
July 08, 2024, 09:55:24 PM
post Re: Syntherrupter - A Feature-rich, Polyphonic Interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Cameron Prince
July 08, 2024, 09:18:21 PM
post Re: Syntherrupter - A Feature-rich, Polyphonic Interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Max
July 08, 2024, 05:17:49 PM
post Re: Syntherrupter - A Feature-rich, Polyphonic Interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Cameron Prince
July 08, 2024, 04:49:20 PM
post Re: Tesla coil in FEMM
[Beginners]
Simranjit
July 08, 2024, 04:28:43 AM
post Re: Tesla coil in FEMM
[Beginners]
davekni
July 08, 2024, 04:06:53 AM
post Tesla coil in FEMM
[Beginners]
Simranjit
July 08, 2024, 03:46:49 AM
post Re: Best core material for QCW Buck modulator ?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
July 08, 2024, 02:42:00 AM
post Re: QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
July 08, 2024, 01:37:55 AM
post Re: First DRSSTC Build- Issues with Fibernet project
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Sebigamer
July 08, 2024, 12:53:08 AM
post Re: QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Anders Mikkelsen
July 08, 2024, 12:49:48 AM
post Re: Silicon(e) plasma
[General Chat]
alan sailer
July 07, 2024, 11:15:35 PM
post Silicon(e) plasma
[General Chat]
MechatEng2023
July 07, 2024, 11:04:43 PM
post Re: QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
July 07, 2024, 09:39:07 PM
post Re: First DRSSTC Build- Issues with Fibernet project
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 07, 2024, 05:32:56 PM
post Re: QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Anders Mikkelsen
July 07, 2024, 02:52:19 PM
post Re: No change in Phase Lead
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Anders Mikkelsen
July 07, 2024, 02:50:04 PM
post Re: Best core material for QCW Buck modulator ?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Anders Mikkelsen
July 07, 2024, 02:20:11 PM
post Teardown of a APC SmartUPS VT 40 kVA
[Electronic Circuits]
Mads Barnkob
July 07, 2024, 10:02:22 AM
post First DRSSTC Build- Issues with Fibernet project
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Sebigamer
July 07, 2024, 09:23:58 AM
post Re: QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
July 07, 2024, 12:44:53 AM
post Re: FEMM tesla coil simulation
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
July 07, 2024, 12:08:50 AM
post Re: FEMM tesla coil simulation
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 06, 2024, 10:35:49 PM
post FEMM tesla coil simulation
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
July 06, 2024, 09:42:43 PM
post Re: No change in Phase Lead
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 06, 2024, 06:06:23 PM
post Re: No change in Phase Lead
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
July 06, 2024, 10:21:16 AM
post Re: No change in Phase Lead
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
July 06, 2024, 10:15:42 AM
post Re: QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
July 06, 2024, 04:53:56 AM
post Re: No change in Phase Lead
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 06, 2024, 04:42:16 AM
post Re: QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 06, 2024, 04:09:50 AM
post Re: Best core material for QCW Buck modulator ?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 06, 2024, 03:07:11 AM
post Re: No change in Phase Lead
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 06, 2024, 03:05:18 AM
post Re: QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
July 06, 2024, 02:37:16 AM
post Re: QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
July 06, 2024, 02:20:14 AM
post QCWDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
July 06, 2024, 01:55:14 AM
post Re: No change in Phase Lead
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 05, 2024, 11:50:37 PM
post Best core material for QCW Buck modulator ?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
July 05, 2024, 10:07:04 PM
post 230v Tesla coil and krypton gas
[Spark Gap Tesla Coils (SGTC)]
gravitysrainbow
July 05, 2024, 07:13:25 PM
post Re: No change in Phase Lead
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
July 05, 2024, 06:17:13 PM
post Re: Phase lead inductors
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
July 04, 2024, 11:40:45 PM
post Re: Sling Psychrometer
[Laboratories, Equipment and Tools]
Twospoons
July 04, 2024, 11:02:32 PM
post Phase lead inductors
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 04, 2024, 06:28:08 PM
post Re: Sling Psychrometer
[Laboratories, Equipment and Tools]
klugesmith
July 04, 2024, 12:31:40 AM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Alex_1996
July 04, 2024, 12:07:21 AM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Alex_1996
July 04, 2024, 12:06:17 AM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
July 03, 2024, 10:51:23 PM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
July 03, 2024, 09:44:14 PM
post Re: Coax cable for DRSSTC interrupter?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
July 03, 2024, 08:48:13 PM
post Re: Coax cable for DRSSTC interrupter?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
July 03, 2024, 08:24:50 PM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Alex_1996
July 03, 2024, 08:12:55 PM
post Re: Coax cable for DRSSTC interrupter?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
July 03, 2024, 07:29:53 PM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
July 03, 2024, 07:21:38 PM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 03, 2024, 05:05:39 PM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Alex_1996
July 03, 2024, 04:29:53 PM
post Re: FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 03, 2024, 04:09:11 PM
post FIRST DRSSTC SKM400GB128D OCD SETTING
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Alex_1996
July 03, 2024, 02:47:18 PM
post Re: Eliminating discharges from a SSTC
[Solid State Tesla Coils (SSTC)]
Alex_1996
July 03, 2024, 01:35:24 PM
post Re: Coax cable for DRSSTC interrupter?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
July 03, 2024, 02:19:03 AM
post Re: Coax cable for DRSSTC interrupter?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
verliebt_in_neukölln17
July 03, 2024, 01:19:50 AM
post Coax cable for DRSSTC interrupter?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
July 02, 2024, 11:29:18 PM
post Re: Is this a good pulse experiment capacitor?
[Capacitor Banks]
Mads Barnkob
July 02, 2024, 09:59:07 PM
post Re: LabCoatz Staccato QCW No straight sparks
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
July 02, 2024, 09:55:53 PM
post Re: Capacitor wiring for single phase 240 to split phase (180 degree) 240v
[Capacitor Banks]
klugesmith
July 02, 2024, 09:44:55 PM
post Re: LabCoatz Staccato QCW No straight sparks
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
July 02, 2024, 07:51:37 PM
post Re: LabCoatz Staccato QCW No straight sparks
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
July 02, 2024, 06:14:07 PM
post Is this a good pulse experiment capacitor?
[Capacitor Banks]
FPS
July 02, 2024, 06:02:38 PM
post Re: LabCoatz Staccato QCW No straight sparks
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
July 02, 2024, 11:37:46 AM
post Re: Building my first DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 02, 2024, 05:22:10 AM
post Re: Coulometric hourmeters
[Laboratories, Equipment and Tools]
davekni
July 02, 2024, 05:16:30 AM
post Re: Building my first DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
drobotk
July 01, 2024, 11:50:12 PM
post Re: Restoring a Rogowski coil calibrator
[Capacitor Banks]
klugesmith
July 01, 2024, 08:48:53 PM
post Uses for Weston's Little Bee probe
[Laboratories, Equipment and Tools]
klugesmith
July 01, 2024, 08:40:59 AM
post Re: Coulometric hourmeters
[Laboratories, Equipment and Tools]
klugesmith
July 01, 2024, 08:09:42 AM
post Re: Coulometric hourmeters
[Laboratories, Equipment and Tools]
davekni
June 30, 2024, 06:49:45 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal