Author Topic: Benjamin's DRSSTC 2 in progress  (Read 4335 times)

Offline Benjamin Lockhart

  • High Voltage Experimenter
  • **
  • Posts: 96
  • Karma: +12/-0
    • View Profile
Benjamin's DRSSTC 2 in progress
« on: September 10, 2023, 10:25:28 PM »
Hey guys,
I'm really excited I just got my big DRSSTC oscillating under feedback


It uses a Phillip Slawinski UD+
0.365 uF MMC
8 inch secondary coil
about 50kHz secondary fres
CM300 fullbridge

I am  trying to set the phase lead in the driver now. I can just make out some spikes on the igbt collector-emitter signal but barely.
This is one low side IGBT, and the primary current. The bus voltage is about 120V dc, the primary current rings up to around 225A. 150us on time.
And yes this is a different scope than in the picture above.

With a slight dummy load sitting on the coil.


without the dummy load the first spike goes down a bit.


zoomed in, the spikes pretty much disappear, also some wrong triggering I couldn't get rid of.


Two different phase lead settings with the dummy load.



What do you think about these waveforms?
Thanks, Benjamin
« Last Edit: September 14, 2023, 06:55:24 AM by Benjamin Lockhart »

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2826
  • Karma: +134/-2
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: Benjamin's DRSSTC 2 in progress
« Reply #1 on: September 11, 2023, 01:14:49 AM »
Quote
I'm having a bit of trouble getting my analog scope to trigger cleanly to set the phase lead in the driver. I can just make out some spikes on the igbt collector-emitter signal but barely.
First simple step is to set trigger holdoff long enough to avoid multiple triggers within one enable pulse (one burst of oscillation).
Second, I'd try triggering on the current feedback signal (signal across 51 ohm burden resistor presuming input looks like UD2.7).  Or if you have a another CT output for scoping, use that.  Then hopefully you can trigger reliably on the first cycle that exceeds whatever current threshold you set.
Third, if your analog scope is fancy enough, use delayed trigger mode.  Set main trigger mode for current, with delay mode to enable trigger on H-bridge output.  That should clean up much of the jitter remaining with a simple current trigger.  (Or set both main and delayed trigger to H-bridge output, using delay to wait for current to build to desired level for checking phase lead.)

Good luck with your build!

Edit:  Saw above edit after posting.  Spikes near the beginning of a burst are normal, at least for UD2.7.  Phase lead does not work properly until current builds some.  Not as important early either since switching current is low.

Final scope capture definitely looks cleanest.

Are you using chop or alternate mode?  The disappearing spikes look more like an artifact of alternate mode, with trigger capturing first part of a burst when scoping current and a later part when scoping H-bridge output.  I'd suggest using chop mode.  Sufficient trigger hold-off should also fix that issue.
« Last Edit: September 11, 2023, 01:22:01 AM by davekni »
David Knierim

Offline Benjamin Lockhart

  • High Voltage Experimenter
  • **
  • Posts: 96
  • Karma: +12/-0
    • View Profile
Re: Benjamin's DRSSTC 2 in progress
« Reply #2 on: September 11, 2023, 04:46:35 AM »
Thanks, triggering from the primary current CT with DC coupling, and playing with holdoff helped a lot.
Alt vs chop didn't seem to matter very much.
Also fine tuning the startup oscillator got rid of the first spike completely! it's only set for one cycle right now and that seems to work fine.

Unfortunately I can only run the bridge up to 130V DC with isolation so I can scope it. I have 45V step down transformer.

Any tips before I set up for first light testing?

Thanks, Benjamin
« Last Edit: September 11, 2023, 04:48:58 AM by Benjamin Lockhart »

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2826
  • Karma: +134/-2
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: Benjamin's DRSSTC 2 in progress
« Reply #3 on: September 11, 2023, 05:28:09 AM »
Quote
Alt vs chop didn't seem to matter very much.
In most cases alt vs chop does not matter, especially with holdoff set correctly to get one trigger per burst.  However, occasionally alternate can produce seemingly-impossible captures, as in the earlier capture labeled:
"zoomed in, the spikes pretty much disappear, also some wrong triggering I couldn't get rid of."
Even ignoring the jitter, that capture appears to show current continuing to increase each cycle while H-bridge output has stopped.  That is not a real situation.  Capture of current was by chance occurring first while still increasing, followed by capture of H-bridge output voltage later as it ended.
For that reason I almost always avoided alt mode.  Used it only occasionally, when signal being scoped was close to chop frequency, which caused artifacts.  Even then I'd switch back and forth to make sure I wasn't getting a false display due to alternate mode.

Quote
Any tips before I set up for first light testing?
Key advice is test at low duty cycle.  Minimizes chances of hard failures if you find issues.

If your H-bridge Vbus supply is a voltage doubler from line, it may be possible to scope.  Make neutral center of doubler caps.  Connect scope probe through a capacitor (0.1uF or so) to neutral or Vbus-.  Neutral should be close to ground potential, with some ripple due to line power wire IR drop.  Capacitor provides high-frequency coupling to scope ground.  H-bridge outputs should be reasonable to view in spite of that bit of ripple.
David Knierim

Offline Benjamin Lockhart

  • High Voltage Experimenter
  • **
  • Posts: 96
  • Karma: +12/-0
    • View Profile
Re: Benjamin's DRSSTC 2 in progress
« Reply #4 on: September 11, 2023, 06:02:59 AM »
Interesting, the supply is a doubler. I don't have a 100:1 probe though. I'm not sure if I can run it off 120V AC and use a 10:1 probe on the bridge.

Offline Mads Barnkob

  • Administrator
  • Executive Board Member
  • *****
  • Posts: 2301
  • Karma: +73/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Benjamin's DRSSTC 2 in progress
« Reply #5 on: September 11, 2023, 12:17:34 PM »
Quote
Any tips before I set up for first light testing?
Key advice is test at low duty cycle.  Minimizes chances of hard failures if you find issues.

Keep DCbus above 100 VDC to avoid excessive transient ratio from IGBT output capacitance. Low voltage testing like 50VDC can fool you to think there is very large switching spikes, as the spike from the output capacitance is the same at 50VDCbus as 500VDCbus, it will look 10 times worse at the low voltage.

Keep BPS at 100BPS'ish and duty cycle low. If you also use low BPS, you can get weird intermittent errors, where the driver is not getting enough feedback.
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2826
  • Karma: +134/-2
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: Benjamin's DRSSTC 2 in progress
« Reply #6 on: September 12, 2023, 05:46:33 AM »
Quote
Interesting, the supply is a doubler. I don't have a 100:1 probe though. I'm not sure if I can run it off 120V AC and use a 10:1 probe on the bridge.
Depends on voltage rating of your 10x probe.  Many are good to 600V.  Voltage rating does decrease as frequency increases.  At low duty cycle, frequency derating of probe is less important.
David Knierim

Offline Benjamin Lockhart

  • High Voltage Experimenter
  • **
  • Posts: 96
  • Karma: +12/-0
    • View Profile
Re: Benjamin's DRSSTC 2 in progress
« Reply #7 on: September 13, 2023, 07:44:25 PM »
Well I seem to have blown the driver.

The 24V input reads like there is a diode across it, and it's shorting the 24V psu.
I don't know why, perhaps a line filter going into the psu might have helped?

The only things I can think of are that I didn't use distilled water, just clean well water, in the primary cooling loop, so maybe some voltage made it's way into the 120V line through the pump, and somehow through the 24 psu and killed something in the driver?
Or maybe voltage on the ground?

All grounds are tied together, to mains ground, and a 10 foot ground rod.

It was making some small output, 8 inches or so at 140V AC input, but I think that's because I had the OCD set at around 300A. it was skipping a lot of pulses and acting kind of erratic.
It was in tune though, the scope confirmed this because the primary current was notching.

I'd appreciate any advice you have.

Offline Mads Barnkob

  • Administrator
  • Executive Board Member
  • *****
  • Posts: 2301
  • Karma: +73/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Benjamin's DRSSTC 2 in progress
« Reply #8 on: September 13, 2023, 08:06:04 PM »
The only things I can think of are that I didn't use distilled water, just clean well water, in the primary cooling loop, so maybe some voltage made it's way into the 120V line through the pump, and somehow through the 24 psu and killed something in the driver?

Even tap water will not carry any real current at those hose lengths. Steve Ward wrote many years ago that even distilled water is useless and he just used tap water. After a few hours of using distilled water, it has been contaminated by surrounding, ion movement from electrolysis etc.
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline Benjamin Lockhart

  • High Voltage Experimenter
  • **
  • Posts: 96
  • Karma: +12/-0
    • View Profile
Re: Benjamin's DRSSTC 2 in progress
« Reply #9 on: September 13, 2023, 10:15:20 PM »
Ok, thanks. I need to do some testing on the driver to find out exactly what's wrong.
Could the grounding have something to do with it?

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2826
  • Karma: +134/-2
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: Benjamin's DRSSTC 2 in progress
« Reply #10 on: September 14, 2023, 06:13:53 AM »
Quote
Ok, thanks. I need to do some testing on the driver to find out exactly what's wrong.
Could the grounding have something to do with it?
Any chance the PSU got confused and generated more than 24V?  Yes, will help to see what's wrong with driver.

AstRii just posted about his experience with FPGA resetting during ground strike rail hits when driver is grounded:
    https://highvoltageforum.net/index.php?topic=2585.msg19148#msg19148
However, I always ground everything and haven't had such an issue.

Is your driver grounded well to it's shield box?  Looks like so in your picture.

Other than PSU over-voltage, only other thought that comes to mind is driver FPGA getting confused and generating high frequency output that overheated output FETs or driver chips due to rapid switching.
David Knierim

Offline Benjamin Lockhart

  • High Voltage Experimenter
  • **
  • Posts: 96
  • Karma: +12/-0
    • View Profile
Re: Benjamin's DRSSTC 2 in progress
« Reply #11 on: March 15, 2024, 08:56:58 PM »
I've got an update on this build. I'm rebuilding it completely except for the primary and secondary. I've reduced the box from 20 inches to 16 inches square and I'm doubling the bus capacitance to 9900uF.

I got the UD+ fixed, it was just one dead output FET. I'm still not quite sure why it died but I'll keep an eye on temps.

I decided to use a double full bridge after seeing a split MMC used on Phillip Slawinski and Cameron Prince's tesla guns to force equal current sharing.
I'm wiring it like this unless anyone can see a reason this won't work well.

Hopefully the current will be split evenly enough to run close to twice the current of a single bridge.

I'm increasing the MMC to 0.66uF total


« Last Edit: March 15, 2024, 09:01:04 PM by Benjamin Lockhart »

Offline Benjamin Lockhart

  • High Voltage Experimenter
  • **
  • Posts: 96
  • Karma: +12/-0
    • View Profile
Re: Benjamin's DRSSTC 2 in progress
« Reply #12 on: March 19, 2024, 06:41:39 AM »
The new inverter bus assembly is done!




Offline Mads Barnkob

  • Administrator
  • Executive Board Member
  • *****
  • Posts: 2301
  • Karma: +73/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Benjamin's DRSSTC 2 in progress
« Reply #13 on: March 19, 2024, 04:31:02 PM »
Beautiful work on that bridge, I love to see some nice handmade items :)

I never tried split MMC, so looking forward to hear more about your experience in that field.

I think your poor little half-bridge rectifier SKKD 100/12, is going to suffer a bit, you might need a bigger one. Surge overload current capabilities is however helped with a much lower Vrrm voltage, as you are properly at 500-600VDC?
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline Benjamin Lockhart

  • High Voltage Experimenter
  • **
  • Posts: 96
  • Karma: +12/-0
    • View Profile
Re: Benjamin's DRSSTC 2 in progress
« Reply #14 on: March 19, 2024, 11:12:24 PM »
Thanks Mads, I thought that a 100A rectifier would be ok for a coil running off a 50A breaker?
I have a single phase 240V supply so the bus voltage should be 680V with no load.

Offline flyingperson23

  • High Voltage Technician
  • ***
  • Posts: 157
  • Karma: +5/-2
  • noob :)
    • View Profile
Re: Benjamin's DRSSTC 2 in progress
« Reply #15 on: March 20, 2024, 12:30:30 AM »
The breaker supplies 50A RMS. Peaks will be higher, especially with a voltage doubler.

Offline Mads Barnkob

  • Administrator
  • Executive Board Member
  • *****
  • Posts: 2301
  • Karma: +73/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Benjamin's DRSSTC 2 in progress
« Reply #16 on: March 20, 2024, 10:39:47 AM »
Thanks Mads, I thought that a 100A rectifier would be ok for a coil running off a 50A breaker?
I have a single phase 240V supply so the bus voltage should be 680V with no load.

There is some derating graphs in the datasheet. Here both sine wave and rectangular are mentioned, where the rectangular causes higher dissipation etc.
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline Benjamin Lockhart

  • High Voltage Experimenter
  • **
  • Posts: 96
  • Karma: +12/-0
    • View Profile
Re: Benjamin's DRSSTC 2 in progress
« Reply #17 on: March 21, 2024, 02:15:31 AM »
Ok, that makes sense. I have a couple huge 301UR200 stud mount diodes (330A, 2000V) that I can fit in there instead. Should be plenty!

Offline Benjamin Lockhart

  • High Voltage Experimenter
  • **
  • Posts: 96
  • Karma: +12/-0
    • View Profile
Re: Benjamin's DRSSTC 2 in progress
« Reply #18 on: March 21, 2024, 06:31:42 PM »
I have a question.

I was planning to wire the extra gates with more GDT secondaries, but would it be better for switching time matching to parallel the gates directly for the doubled up IGBTs?

Since I've already made gate drive boards for each brick, it would be best if I could continue using them.
I suppose I could use one GDT secondary to feed two separate gate networks through the existing boards.

Thanks, Benjamin

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2826
  • Karma: +134/-2
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: Benjamin's DRSSTC 2 in progress
« Reply #19 on: March 22, 2024, 02:59:25 AM »
Quote
I was planning to wire the extra gates with more GDT secondaries
Yes, I think that would be best, with a caution.
Split MMC balances current at coil frequency.  High frequency (H-bridge output transition edges) are connected more directly through MMC sections that are low impedance at high frequency.  H-bridge output transition timing needs to match.  So GDT windings and lead lengths should be matched including matched coupling to primary.
Best GDT performance (lowest leakage inductance) is using a twisted pair for each gate, half of each pair to IGBT and other half to primary.  All primary windings paralleled.  Ideally each primary winding is twisted together all the way back to driver, connected in parallel only at driver connections.
    https://highvoltageforum.net/index.php?topic=1854.msg13949#msg13949
« Last Edit: March 22, 2024, 01:54:04 PM by Mads Barnkob »
David Knierim

High Voltage Forum

Re: Benjamin's DRSSTC 2 in progress
« Reply #19 on: March 22, 2024, 02:59:25 AM »

 


* Recent Topics and Posts

post Re: Benjamin's DRSSTC3
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Jj
Today at 03:09:41 AM
post Re: Are TVS diodes necessary for full bridge?
[Solid State Tesla Coils (SSTC)]
Simranjit
Today at 01:53:07 AM
post Re: UD+ debugging (randomly skipping pulses)
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
Today at 01:07:30 AM
post Re: UD+ debugging (randomly skipping pulses)
[Dual Resonant Solid State Tesla coils (DRSSTC)]
AstRii
Today at 12:45:22 AM
post Re: UD+ debugging (randomly skipping pulses)
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
June 14, 2024, 10:41:03 PM
post UD+ debugging (randomly skipping pulses)
[Dual Resonant Solid State Tesla coils (DRSSTC)]
AstRii
June 14, 2024, 10:20:00 PM
post Re: Are TVS diodes necessary for full bridge?
[Solid State Tesla Coils (SSTC)]
davekni
June 14, 2024, 09:47:48 PM
post Fronius IG Plus 2LT-2 6kW Solar Inverter Teardown
[Electronic Circuits]
Mads Barnkob
June 14, 2024, 09:40:33 PM
post Re: Are TVS diodes necessary for full bridge?
[Solid State Tesla Coils (SSTC)]
Simranjit
June 14, 2024, 07:44:12 AM
post Re: Are TVS diodes necessary for full bridge?
[Solid State Tesla Coils (SSTC)]
davekni
June 14, 2024, 05:21:55 AM
post Re: Are TVS diodes necessary for full bridge?
[Solid State Tesla Coils (SSTC)]
Simranjit
June 14, 2024, 03:24:43 AM
post Re: Are TVS diodes necessary for full bridge?
[Solid State Tesla Coils (SSTC)]
davekni
June 14, 2024, 03:13:44 AM
post Re: Are TVS diodes necessary for full bridge?
[Solid State Tesla Coils (SSTC)]
Simranjit
June 14, 2024, 02:27:06 AM
post Re: Are TVS diodes necessary for full bridge?
[Solid State Tesla Coils (SSTC)]
davekni
June 14, 2024, 01:56:58 AM
post Are TVS diodes necessary for full bridge?
[Solid State Tesla Coils (SSTC)]
Simranjit
June 13, 2024, 11:21:46 PM
post Re: Bigger sparks?...
[Vacuum Tube Tesla Coils (VTTC)]
Teslaventje
June 13, 2024, 08:50:56 PM
post Re: Steve Ward's DRSSTC Interrupter stops working when adjusting pulse width
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
June 13, 2024, 07:43:37 PM
post Re: Steve Ward's DRSSTC Interrupter stops working when adjusting pulse width
[Dual Resonant Solid State Tesla coils (DRSSTC)]
petespaco
June 13, 2024, 04:52:08 PM
post Re: Turning SSTC into DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
June 13, 2024, 02:14:17 AM
post Re: Turning SSTC into DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
June 12, 2024, 11:04:57 PM
post Turning SSTC into DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Simranjit
June 12, 2024, 10:23:08 PM
post Re: UD2.7C constantly in OCP despite having signal
[Dual Resonant Solid State Tesla coils (DRSSTC)]
verliebt_in_neukölln17
June 12, 2024, 08:41:06 PM
post Re: UD2.7C constantly in OCP despite having signal
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
June 12, 2024, 07:53:31 PM
post Re: Van de Graaf Voltage measurement with voltage sensor and voltage divider
[Static Electricity]
haversin
June 12, 2024, 06:57:13 PM
post UD2.7C constantly in OCP despite having signal
[Dual Resonant Solid State Tesla coils (DRSSTC)]
verliebt_in_neukölln17
June 12, 2024, 06:54:49 PM
post Re: Van de Graaf Voltage measurement with voltage sensor and voltage divider
[Static Electricity]
Mads Barnkob
June 12, 2024, 03:47:28 PM
post Van de Graaf Voltage measurement with voltage sensor and voltage divider
[Static Electricity]
vK
June 12, 2024, 03:42:18 AM
post Re: Bigger sparks?...
[Vacuum Tube Tesla Coils (VTTC)]
davekni
June 12, 2024, 03:32:22 AM
post Re: Bigger sparks?...
[Vacuum Tube Tesla Coils (VTTC)]
Teslaventje
June 11, 2024, 11:05:49 PM
post Re: Bigger sparks?...
[Vacuum Tube Tesla Coils (VTTC)]
MRMILSTAR
June 11, 2024, 05:36:46 AM
post Re: Sling Psychrometer
[Laboratories, Equipment and Tools]
Twospoons
June 11, 2024, 12:29:31 AM
post Bigger sparks?...
[Vacuum Tube Tesla Coils (VTTC)]
Teslaventje
June 10, 2024, 11:05:55 PM
post Re: Syntherrupter - A Feature-rich, Polyphonic Interrupter
[Computers, Microcontrollers, Programmable Logic, Interfaces and Displays]
Max
June 10, 2024, 10:57:51 PM
post Re: Benjamin's DRSSTC3
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
June 10, 2024, 08:08:04 PM
post Re: Plasma Torid - Class E Self Resonant Dual/Stereo - Plasma Torid Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hi-Deff
June 10, 2024, 06:04:09 PM
post Sling Psychrometer
[Laboratories, Equipment and Tools]
klugesmith
June 10, 2024, 04:43:59 PM
post Re: Benjamin's DRSSTC3
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
June 10, 2024, 03:35:28 PM
post Re: Benjamin's DRSSTC3
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Jj
June 10, 2024, 01:36:41 PM
post Re: Is a 60UF 800VDC Dawncap good for an induction heater?
[General Chat]
Anders Mikkelsen
June 09, 2024, 05:44:29 PM
post Is a 60UF 800VDC Dawncap good for an induction heater?
[General Chat]
yourboi
June 09, 2024, 03:31:30 PM
post Re: Steve Ward's DRSSTC Interrupter stops working when adjusting pulse width
[Dual Resonant Solid State Tesla coils (DRSSTC)]
NyaaX_X
June 09, 2024, 01:34:49 PM
post Steve Ward's DRSSTC Interrupter stops working when adjusting pulse width
[Dual Resonant Solid State Tesla coils (DRSSTC)]
verliebt_in_neukölln17
June 09, 2024, 01:56:51 AM
post Re: Return of Electronics Flea Market in "Silicon Valley"
[Sell / Buy / Trade]
klugesmith
June 08, 2024, 06:06:25 AM
post Re: Coulometric hourmeters
[Laboratories, Equipment and Tools]
klugesmith
June 08, 2024, 05:38:14 AM
post Interrupter for SSTC
[Beginners]
Simranjit
June 08, 2024, 12:47:47 AM
post Re: Adding capacitor to primary in SSTC
[Solid State Tesla Coils (SSTC)]
Michelle_
June 07, 2024, 03:59:57 PM
post Re: Adding capacitor to primary in SSTC
[Solid State Tesla Coils (SSTC)]
davekni
June 07, 2024, 06:42:26 AM
post Re: Space-X Starship test this week
[Science, Research and News In Other Fields Than Electronics]
MRMILSTAR
June 07, 2024, 05:08:00 AM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
davekni
June 07, 2024, 03:16:31 AM
post Re: Space-X Starship test this week
[Science, Research and News In Other Fields Than Electronics]
klugesmith
June 06, 2024, 11:37:20 PM
post Adding capacitor to primary in SSTC
[Solid State Tesla Coils (SSTC)]
Simranjit
June 06, 2024, 11:20:23 PM
post Re: Plasma Torid - Class E Self Resonant Dual/Stereo - Plasma Torid Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
June 06, 2024, 10:54:48 PM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
ZakW
June 06, 2024, 05:17:02 AM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
Simranjit
June 06, 2024, 04:50:00 AM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
davekni
June 06, 2024, 04:00:52 AM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
ZakW
June 06, 2024, 01:43:41 AM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
Simranjit
June 05, 2024, 11:11:17 PM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
Michelle_
June 05, 2024, 10:18:57 PM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
Simranjit
June 05, 2024, 10:13:03 PM
post Re: Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
ZakW
June 05, 2024, 09:29:18 PM
post Half bridge sstc different waveform on two mosfets
[Solid State Tesla Coils (SSTC)]
Simranjit
June 05, 2024, 08:46:53 PM
post Re: Want to build HV HF oscilloscope probe.
[Electronic Circuits]
Twospoons
June 05, 2024, 07:04:45 AM
post Re: Want to build HV HF oscilloscope probe.
[Electronic Circuits]
Domo
June 05, 2024, 04:58:35 AM
post Re: Pearson current monitor model 1330 teardown (100kA)
[Laboratories, Equipment and Tools]
klugesmith
June 05, 2024, 01:42:04 AM
post Re: Coulometric hourmeters
[Laboratories, Equipment and Tools]
klugesmith
June 04, 2024, 10:31:58 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
pete_dl
June 04, 2024, 08:08:28 PM
post Re: Want to build HV HF oscilloscope probe.
[Electronic Circuits]
Twospoons
June 03, 2024, 11:13:26 PM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
June 03, 2024, 10:35:57 PM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hi-Deff
June 03, 2024, 05:51:05 PM
post Re: Want to build HV HF oscilloscope probe.
[Electronic Circuits]
Domo
June 03, 2024, 07:41:41 AM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
June 03, 2024, 05:28:44 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
June 03, 2024, 05:02:19 AM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
June 03, 2024, 03:47:33 AM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
June 03, 2024, 02:23:58 AM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hi-Deff
June 03, 2024, 01:25:24 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
June 03, 2024, 01:08:47 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
June 02, 2024, 10:29:02 PM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
June 02, 2024, 10:02:45 PM
post Re: Racing sparks
[Spark Gap Tesla Coils (SGTC)]
davekni
June 02, 2024, 08:25:37 PM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
June 02, 2024, 04:51:58 PM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Michelle_
June 02, 2024, 04:44:30 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
MRMILSTAR
June 02, 2024, 03:25:11 PM
post APC Smart-UPS 1500VA Teardown
[Electronic Circuits]
Mads Barnkob
June 02, 2024, 01:36:11 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
pete_dl
June 02, 2024, 11:43:40 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
June 02, 2024, 08:49:11 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
June 02, 2024, 08:36:07 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
June 02, 2024, 12:41:50 AM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Benjamin Lockhart
June 01, 2024, 08:24:35 PM
post Pearson current monitor model 1330 teardown (100kA)
[Laboratories, Equipment and Tools]
Mads Barnkob
June 01, 2024, 08:22:28 PM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
June 01, 2024, 03:56:53 AM
post Re: Racing sparks
[Spark Gap Tesla Coils (SGTC)]
Terry
June 01, 2024, 12:03:50 AM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hi-Deff
May 31, 2024, 11:46:20 PM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
Michelle_
May 31, 2024, 06:13:59 PM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
May 31, 2024, 01:55:22 AM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
May 30, 2024, 11:57:49 PM
post Re: First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
May 30, 2024, 11:50:06 PM
post First DRSSTC questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hi-Deff
May 30, 2024, 11:23:35 PM
post Re: Steve Ward SSTC5 build
[Solid State Tesla Coils (SSTC)]
davekni
May 30, 2024, 10:43:06 PM
post Re: Benjamin's DRSSTC3
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
May 30, 2024, 10:24:35 PM
post Re: SSTC tripping circuit breaker
[Solid State Tesla Coils (SSTC)]
NyaaX_X
May 30, 2024, 06:10:04 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal