Author Topic: LabCoatz Staccato QCW No straight sparks  (Read 1765 times)

Offline Admiral Aaron Ravensdale

  • High Voltage Enthusiast
  • *
  • Posts: 13
  • Karma: +0/-0
    • View Profile
LabCoatz Staccato QCW No straight sparks
« on: February 21, 2024, 02:31:59 PM »
Hi new build, new issues :-(
I build the Staccato QCW out of this Video.

With the following stats.



and shematic


Now I run into the issue that I don't get straight sparks!
First I try it with a 28cm Toroid and 337kHz@15nf
and now with a 20cm Toroid and 378kHz @40nf
With an Probe in the air it looks like the ramp is very short but i can change the time like described from 1ms to 8 ms



also confirmed the 378kHz when I zoom in on the upper picture




also the Signal at the Pin "Int" of the shematic looks good





But you can see only wild sparking more like an DRSSTC than QCW
any ideas whats wrong?


Video with 200VAC and all pulse width
https://photos.app.goo.gl/t16hUAzQX47Hd1Gm6
« Last Edit: February 21, 2024, 03:07:32 PM by Admiral Aaron Ravensdale »

Offline ZakW

  • High Voltage Technician
  • ***
  • Posts: 180
  • Karma: +6/-0
  • YouTube @QZW_Labs
    • View Profile
Re: LabCoatz Staccato QCW No straight sparks
« Reply #1 on: February 21, 2024, 06:58:39 PM »
Hello,

You first probe waveform looks to be the issue. You have a sharp spike in the beginning instead of a ramp. That spike is going to cause arcs to branch a lot. Are you powering the coil with unfiltered rectified AC (no bulk capacitors to smooth input voltage)?

The zero cross detector might not be triggering at the zero crossing, here is an example of that: When the coil turns on too late into the AC half cycle (ramp) it causes more of a burst of power into the primary rather than a more gradual ramp. What AC source are you using for the ZCD? In the picture, the purple trace is the probe hanging in air. Yellow is from an AC transformer.




This is the wave form you are looking for: Blue is the probe hanging in the air by the coil. Coil turns on at or as close to zero crossing and ramps up as AC voltage increases.


The 1-8ms adjustment determines when the coil shuts off. It should always trigger as close to the start of the AC half cycle (zero crossing) and then can be adjusted to shut off before the cycle has ended.

Good luck!

Offline Admiral Aaron Ravensdale

  • High Voltage Enthusiast
  • *
  • Posts: 13
  • Karma: +0/-0
    • View Profile
Re: LabCoatz Staccato QCW No straight sparks
« Reply #2 on: February 21, 2024, 07:28:29 PM »

Thanks for the reply.


You first probe waveform looks to be the issue. You have a sharp spike in the beginning instead of a ramp. That spike is going to cause arcs to branch a lot. Are you powering the coil with unfiltered rectified AC (no bulk capacitors to smooth input voltage)?

The side of the Power Input for the IGBT looks like that 2 Caps 250V 1000uf in series and a 1600V 100A Brick rectifier
 [ Invalid Attachment ]
The zero cross detector might not be triggering at the zero crossing, here is an example of that: When the coil turns on too late into the AC half cycle (ramp) it causes more of a burst of power into the primary rather than a more gradual ramp. What AC source are you using for the ZCD? In the picture, the purple trace is the probe hanging in air. Yellow is from an AC transformer.
I use this transformer 12.6V AC
 [ Invalid Attachment ]


This is the wave form you are looking for: Blue is the probe hanging in the air by the coil. Coil turns on at or as close to zero crossing and ramps up as AC voltage increases.

OK this looks quiet different.
How can I figure out if the which side cause the issue?

THANKS!


Offline ZakW

  • High Voltage Technician
  • ***
  • Posts: 180
  • Karma: +6/-0
  • YouTube @QZW_Labs
    • View Profile
Re: LabCoatz Staccato QCW No straight sparks
« Reply #3 on: February 21, 2024, 07:48:47 PM »
Quote
The side of the Power Input for the IGBT looks like that 2 Caps 250V 1000uf in series and a 1600V 100A Brick rectifier
That is the issue. Just remove those capacitors and you should be good to go.

Since this is a ramped coil, you are trying to utilize the AC input (sine wave) ramp shape. With the filtering capacitors you are effective getting rid of that and smoothing it all out. So the coil is getting a high voltage pulse at startup.

The only other thing that you might need to verify is that the zero cross AC transformer is in phase with the AC bridge input. If you dont get any arcs after removing the filtering caps, try reversing the zero crossing transformer input.

nice build btw, those are some hefty resonant capacitors!

Offline Admiral Aaron Ravensdale

  • High Voltage Enthusiast
  • *
  • Posts: 13
  • Karma: +0/-0
    • View Profile
Re: LabCoatz Staccato QCW No straight sparks
« Reply #4 on: February 21, 2024, 08:53:07 PM »
Quote
The side of the Power Input for the IGBT looks like that 2 Caps 250V 1000uf in series and a 1600V 100A Brick rectifier
That is the issue. Just remove those capacitors and you should be good to go.


THHHHAAAAANNNKS worked now  ;D


Since this is a ramped coil, you are trying to utilize the AC input (sine wave) ramp shape. With the filtering capacitors you are effective getting rid of that and smoothing it all out. So the coil is getting a high voltage pulse at startup.

The only other thing that you might need to verify is that the zero cross AC transformer is in phase with the AC bridge input. If you dont get any arcs after removing the filtering caps, try reversing the zero crossing transformer input.

nice build btw, those are some hefty resonant capacitors!
which build? it's just the test crappy test look.
Later it looks like this QCW where I currently wait for the "Simple Driver" from Ukrain but you know the war and the struggle there is real, I mailed already with he is still alive but he spend nearly every day in a bunker somewhere in Kiev and don't get parts :-(




Offline ZakW

  • High Voltage Technician
  • ***
  • Posts: 180
  • Karma: +6/-0
  • YouTube @QZW_Labs
    • View Profile
Re: LabCoatz Staccato QCW No straight sparks
« Reply #5 on: February 21, 2024, 09:04:11 PM »
You're welcome! Happy to hear that it is working now.

-Zak

Offline Admiral Aaron Ravensdale

  • High Voltage Enthusiast
  • *
  • Posts: 13
  • Karma: +0/-0
    • View Profile
Re: LabCoatz Staccato QCW No straight sparks
« Reply #6 on: February 21, 2024, 09:13:05 PM »
Nice!
This is how QCW Sparks should look like \o/
https://photos.app.goo.gl/DHpoqBSRY8W7kuWW8

@ZakW Got all my HV Caps from aliexpress Dawncap is a really good brand.
https://de.aliexpress.com/item/4000314891877.html
https://de.aliexpress.com/item/1005004990716404.html
But take care that you order DTR caps


Offline ZakW

  • High Voltage Technician
  • ***
  • Posts: 180
  • Karma: +6/-0
  • YouTube @QZW_Labs
    • View Profile
Re: LabCoatz Staccato QCW No straight sparks
« Reply #7 on: February 21, 2024, 11:37:47 PM »
Nice output, thanks for sharing!

Offline alan sailer

  • High Voltage Engineer
  • ****
  • Posts: 286
  • Karma: +18/-1
    • View Profile
Re: LabCoatz Staccato QCW No straight sparks
« Reply #8 on: February 22, 2024, 12:53:22 AM »
It looks like that antenna is getting a workout. I see corona coming off the tip during every pulse.

The "simple driver" works great. Used it two coils, a DRSSTC and a QCW.  Glad to hear Eugene is still OK. He is a good guy...

Cheers.
« Last Edit: February 22, 2024, 12:56:42 AM by alan sailer »

High Voltage Forum

Re: LabCoatz Staccato QCW No straight sparks
« Reply #8 on: February 22, 2024, 12:53:22 AM »

 


* Recent Topics and Posts

post Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
Today at 05:58:27 AM
post Tesla coil UV eye protection?
[General Chat]
Michelle_
Today at 05:17:22 AM
post Re: Tenebrescent Potassium Iodide
[Solid State Tesla Coils (SSTC)]
alan sailer
Today at 12:39:59 AM
post Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
April 23, 2024, 11:07:41 PM
post Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
April 23, 2024, 10:57:39 PM
post Re: Plasma Torid - Class E Self Resonant Dual/Stereo - Plasma Torid Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
OmGigaTron
April 23, 2024, 09:33:49 PM
post Re: Tenebrescent Potassium Iodide
[Solid State Tesla Coils (SSTC)]
haversin
April 23, 2024, 06:00:42 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 23, 2024, 03:50:49 AM
post Re: Tenebrescent Potassium Iodide
[Solid State Tesla Coils (SSTC)]
alan sailer
April 23, 2024, 03:13:31 AM
post Re: Tenebrescent Potassium Iodide
[Solid State Tesla Coils (SSTC)]
haversin
April 23, 2024, 12:50:40 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 11:21:06 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 08:11:00 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 06:15:30 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
NyaaX_X
April 22, 2024, 05:52:50 PM
post Tenebrescent Potassium Iodide
[Solid State Tesla Coils (SSTC)]
alan sailer
April 22, 2024, 05:52:13 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 04:31:52 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
NyaaX_X
April 22, 2024, 04:05:34 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
markus
April 22, 2024, 01:02:30 PM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
April 22, 2024, 06:32:35 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 06:24:10 AM
post M2000NM1 toroid for gdt tesla coil
[General Chat]
thedark
April 22, 2024, 05:13:15 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 02:25:29 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
alan sailer
April 22, 2024, 02:09:18 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 12:14:21 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 21, 2024, 09:47:15 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
April 21, 2024, 08:34:02 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 21, 2024, 06:09:57 PM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
April 21, 2024, 06:21:54 AM
post Re: Insulate the secondary of the Tesla coil with a PET plastic bottle
[General Chat]
Michelle_
April 21, 2024, 06:18:30 AM
post Re: Insulate the secondary of the Tesla coil with a PET plastic bottle
[General Chat]
davekni
April 21, 2024, 06:12:31 AM
post Re: Insulate the secondary of the Tesla coil with a PET plastic bottle
[General Chat]
MRMILSTAR
April 21, 2024, 05:19:55 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 21, 2024, 02:29:17 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
alan sailer
April 21, 2024, 01:28:59 AM
post Insulate the secondary of the Tesla coil with a PET plastic bottle
[General Chat]
thedark
April 21, 2024, 01:19:44 AM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
April 21, 2024, 12:55:25 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 20, 2024, 11:25:32 PM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
April 20, 2024, 10:28:26 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
davekni
April 20, 2024, 10:23:28 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 20, 2024, 10:06:44 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
davekni
April 20, 2024, 09:21:55 PM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
April 20, 2024, 09:16:14 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
April 20, 2024, 08:58:40 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 20, 2024, 06:18:26 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 20, 2024, 06:15:26 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
April 20, 2024, 03:45:43 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Benjamin Lockhart
April 20, 2024, 06:33:37 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 20, 2024, 05:45:04 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Benjamin Lockhart
April 20, 2024, 05:34:16 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 20, 2024, 04:50:57 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Benjamin Lockhart
April 20, 2024, 04:03:55 AM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
April 20, 2024, 02:35:56 AM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 19, 2024, 09:37:52 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
klugesmith
April 19, 2024, 09:20:10 PM
post Re: Next Gen DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
April 19, 2024, 07:22:26 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 19, 2024, 04:46:36 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
alan sailer
April 19, 2024, 03:49:28 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 19, 2024, 01:53:57 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
MRMILSTAR
April 19, 2024, 05:24:19 AM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Tesla Junior
April 19, 2024, 04:24:09 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 19, 2024, 04:20:35 AM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 19, 2024, 04:05:28 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
alan sailer
April 19, 2024, 04:03:54 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 19, 2024, 03:19:19 AM
post Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
April 19, 2024, 03:09:29 AM
post Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
unrealcrafter2
April 19, 2024, 01:47:37 AM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 19, 2024, 12:19:21 AM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
klugesmith
April 18, 2024, 11:33:01 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 18, 2024, 11:15:15 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
davekni
April 18, 2024, 10:59:36 PM
post Re: What actually kills MOSFETs?
[Beginners]
unrealcrafter2
April 18, 2024, 10:03:48 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
klugesmith
April 18, 2024, 09:53:25 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
unrealcrafter2
April 18, 2024, 09:50:09 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 18, 2024, 09:15:55 PM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
April 18, 2024, 08:50:49 PM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
unrealcrafter2
April 18, 2024, 08:11:27 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
davekni
April 18, 2024, 07:28:05 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 18, 2024, 06:30:30 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 18, 2024, 06:03:57 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 18, 2024, 05:26:13 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
NyaaX_X
April 18, 2024, 04:03:38 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 18, 2024, 02:56:40 PM
post Re: DIY induction guns? (warning:long)
[Induction Launchers, Coil Guns and Rails guns]
Benbmw
April 18, 2024, 06:17:15 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 18, 2024, 05:46:07 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
April 18, 2024, 05:18:31 AM
post Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
April 18, 2024, 04:34:52 AM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
klugesmith
April 18, 2024, 04:11:53 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 18, 2024, 04:02:44 AM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
April 18, 2024, 03:35:52 AM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
MRMILSTAR
April 17, 2024, 11:54:05 PM
post 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
April 17, 2024, 11:37:16 PM
post Re: Has anyone tried to build a TMT (extra coil) Tesla coil?
[General Chat]
Michelle_
April 17, 2024, 02:29:30 AM
post Re: Has anyone tried to build a TMT (extra coil) Tesla coil?
[General Chat]
MRMILSTAR
April 16, 2024, 11:56:12 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
klugesmith
April 16, 2024, 11:46:57 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 16, 2024, 10:40:11 PM
post Has anyone tried to build a TMT (extra coil) Tesla coil?
[General Chat]
Michelle_
April 16, 2024, 09:21:39 PM
post Re: Medium Drsstc question
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
April 16, 2024, 08:04:16 PM
post Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
April 16, 2024, 06:48:05 PM
post Re: Game changing tesla coil secondary winding suggestions
[General Chat]
Michelle_
April 16, 2024, 06:18:40 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 16, 2024, 06:14:53 PM
post Re: 3D printed mini-slayer: world's weakest tesla coil
[Solid State Tesla Coils (SSTC)]
unrealcrafter2
April 16, 2024, 05:44:44 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal