Author Topic: Drsstc feedback startup  (Read 2404 times)

Offline RoamingD

  • High Voltage Enthusiast
  • *
  • Posts: 28
  • Karma: +1/-0
  • Self taught 19yo enthusiast
    • View Profile
Drsstc feedback startup
« on: September 18, 2023, 02:59:10 PM »
Hello, it may sound like a stupid question, but do I need to have my secondary coil in place for my ud2.7c to be able to pick up the feedback signal from the primary coil?
Currently my driver works fine only when it is fed a 120khz square wave, and the feedback transformer when loaded with a 51ohm burden resistor appears on the oscilloscope

Offline flyingperson23

  • High Voltage Technician
  • ***
  • Posts: 107
  • Karma: +5/-2
  • noob :)
    • View Profile
Re: Drsstc feedback startup
« Reply #1 on: September 18, 2023, 04:29:15 PM »
No, the UD operates on primary current feedback; all it needs is for current to be flowing through the primary. If you operate without a secondary, the UD will oscillate normally as current will still flow through the primary.

Offline RoamingD

  • High Voltage Enthusiast
  • *
  • Posts: 28
  • Karma: +1/-0
  • Self taught 19yo enthusiast
    • View Profile
Re: Drsstc feedback startup
« Reply #2 on: September 18, 2023, 05:01:22 PM »
Some quick scope shots, this is the halfbridge output working when the driver is fed a signal
I fed it 170 vac on the bus at some point and nothing blew up so the halfbridge is switching right

This is the feedback transformer loaded on a 51ohm burden resistor and it looks good  ???

but the really strange output is this "starting pulse" that I measured on the gdt when it has no feedback connected, to me it looks inverted, how is this possible?
« Last Edit: September 18, 2023, 05:05:26 PM by RoamingD »

Offline flyingperson23

  • High Voltage Technician
  • ***
  • Posts: 107
  • Karma: +5/-2
  • noob :)
    • View Profile
Re: Drsstc feedback startup
« Reply #3 on: September 18, 2023, 06:20:30 PM »
Those waveforms look normal enough to me. What do you mean by 'inverted'?

Offline RoamingD

  • High Voltage Enthusiast
  • *
  • Posts: 28
  • Karma: +1/-0
  • Self taught 19yo enthusiast
    • View Profile
Re: Drsstc feedback startup
« Reply #4 on: September 18, 2023, 07:46:46 PM »
I mean the output is almost high and has just a short off time, kinda like a high duty cycle, and on the internet I saw quite the opposite, a short positive pulse, not a short gnd pulse like mine, I really don't know, but the circuit isn't able to start it's oscillation from the current transformer

Offline flyingperson23

  • High Voltage Technician
  • ***
  • Posts: 107
  • Karma: +5/-2
  • noob :)
    • View Profile
Re: Drsstc feedback startup
« Reply #5 on: September 19, 2023, 12:45:37 AM »
Did you try changing the phasing on the driver? If your feedback phase is wrong it won't oscillate under its own feedback.

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2680
  • Karma: +127/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: Drsstc feedback startup
« Reply #6 on: September 19, 2023, 06:15:40 AM »
Quote
Some quick scope shots, this is the halfbridge output working when the driver is fed a signal
I fed it 170 vac on the bus at some point and nothing blew up so the halfbridge is switching right
Do you have a bleed resistor pulling half-bridge output low?  Something is causing output to end up at 0V after enable pulse ends.
Looks like Vbus is 60V for this scope capture.  Is that accurate?  Is Vbus 60V for the current transformer output capture too?

Quote
but the really strange output is this "starting pulse" that I measured on the gdt when it has no feedback connected, to me it looks inverted, how is this possible?
Where on GDT are you probing?  Is this low-side Vge (or Vgs if using FETs)?  If so, it looks appropriate, other than possible CT inversion issue as flyingperson23 mentioned.  What does half-bridge output look like?  What does voltage across UD2.7 51-ohm resistor look like?
If this is low-side Vge, then high side Vge should be a matching positive pulse.  That should make a low-to-high transition on half-bridge output.  That output transition should cause current that should trigger another transition.
David Knierim

Offline RoamingD

  • High Voltage Enthusiast
  • *
  • Posts: 28
  • Karma: +1/-0
  • Self taught 19yo enthusiast
    • View Profile
Re: Drsstc feedback startup
« Reply #7 on: September 19, 2023, 07:53:34 AM »
Quote
Do you have a bleed resistor pulling half-bridge output low?  Something is causing output to end up at 0V after enable pulse ends.
Looks like Vbus is 60V for this scope capture.  Is that accurate?  Is Vbus 60V for the current transformer output capture too?
This horrible thing I drew is the schematic of the bridge, I dont use any bleed resistor except on the bus capacitor

and this is how I connected the probe

This is how I connected and measured the feedback transformer with a 120khz signal from a 555 timer fed in the feedback connector, the variac was set to 50v ac

With no feedback transformer/signal generator, this is the startup pulse that I can measure on the gates of the igbt, is this normal?


And I dont think the gdt is the problem because with external feedback, the circuit didnt blow at 170vac input and also no real heating, at some point I was even tripping the ocd
I really dont know what to do, but for a last resort can I run the coil based on the signal generator and ditch primary feedback, keeping in mind the ocd does still work?

Offline flyingperson23

  • High Voltage Technician
  • ***
  • Posts: 107
  • Karma: +5/-2
  • noob :)
    • View Profile
Re: Drsstc feedback startup
« Reply #8 on: September 19, 2023, 03:48:23 PM »
Typically the non-igbt end of a half bridge tank circuit is connected to a capacitive voltage divider, not Vbus-

Offline RoamingD

  • High Voltage Enthusiast
  • *
  • Posts: 28
  • Karma: +1/-0
  • Self taught 19yo enthusiast
    • View Profile
Re: Drsstc feedback startup
« Reply #9 on: September 19, 2023, 03:57:15 PM »
I asked previously about this in this thread https://highvoltageforum.net/index.php?topic=2348.0

Offline Mads Barnkob

  • Administrator
  • Executive Board Member
  • *****
  • Posts: 2243
  • Karma: +70/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Drsstc feedback startup
« Reply #10 on: September 19, 2023, 08:46:36 PM »
I replied to your thread "Re: Inverter question" and I think your problem here is primary coil saturation, from leaving out the DC blocking capacitors. Often they are mistaken for only being used for voltage doubling in 120VAC countries, but that is just a double use of them.
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline RoamingD

  • High Voltage Enthusiast
  • *
  • Posts: 28
  • Karma: +1/-0
  • Self taught 19yo enthusiast
    • View Profile
Re: Drsstc feedback startup
« Reply #11 on: September 19, 2023, 08:53:11 PM »
Oh, I see, but I have one more question, when adding the DC blocking caps does their capacity add up to the MMC?

Offline Mads Barnkob

  • Administrator
  • Executive Board Member
  • *****
  • Posts: 2243
  • Karma: +70/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Drsstc feedback startup
« Reply #12 on: September 19, 2023, 09:10:06 PM »
Oh, I see, but I have one more question, when adding the DC blocking caps does their capacity add up to the MMC?

Not if you calculate it correctly as I linked to in the other thread.
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline RoamingD

  • High Voltage Enthusiast
  • *
  • Posts: 28
  • Karma: +1/-0
  • Self taught 19yo enthusiast
    • View Profile
Re: Drsstc feedback startup
« Reply #13 on: September 19, 2023, 10:02:13 PM »
Quote
Not if you calculate it correctly as I linked to in the other thread.
I am very sorry if my physics or mathematics skills are lacking :))) the resonant freq is 122khz with a 3.808 uH primary coil inductance
I have run the calculations and a 1uF capacitor will have 1.305 Ohms of reactance but the frequency comes at around 0.08164 kHz, will this work?
Also, another beginner question, what should the voltage rating of those caps be? Can I get away with 630v?
« Last Edit: September 19, 2023, 10:46:46 PM by RoamingD »

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2680
  • Karma: +127/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: Drsstc feedback startup
« Reply #14 on: September 20, 2023, 05:24:44 AM »
Quote
I dont use any bleed resistor except on the bus capacitor
Then I'm puzzled as to why half-bridge output returns quickly to 0V (to Vbus-) shortly after a burst.  (This is from first scope capture of reply #2 above.)  Only explanations I'm thinking of at the moment are either there is some glitch in low-side IGBT Vge or the low-side IGBT is partially damaged (leakage current).

Quote
With no feedback transformer/signal generator, this is the startup pulse that I can measure on the gates of the igbt, is this normal?
I'll guess the probe is really 10x, so 20V/div.  Even then it does not look normal.   Initial -24V pulse looks somewhat reasonable, but too short.  Subsequent ring appears clipped, more square than sine wave, and too high frequency for your 122kHz coil.  Are you sure GDT is on ferrite core and not powdered iron?  It may work barely well enough for operation at 122kHz, but not for the initial start transition.

Quote
Typically the non-igbt end of a half bridge tank circuit is connected to a capacitive voltage divider, not Vbus-
Agree.  But I don't think this is a significant cause of issues showing up here.

David Knierim

Offline RoamingD

  • High Voltage Enthusiast
  • *
  • Posts: 28
  • Karma: +1/-0
  • Self taught 19yo enthusiast
    • View Profile
Re: Drsstc feedback startup
« Reply #15 on: September 20, 2023, 05:51:18 AM »
Sadly I am sure the gdt is proper ferrite, I have used this type of core in my 200khz sstc and it was fine, here is a link of it
https://www.tme.eu/ro/details/b64290l0618x830/miezuri-de-ferita/epcos/
Also, I think the output returning to 0 was some kind of weird glitch with that cheap oscilloscope, my trusty analog scope doesn't show it falling, but staying in the middle

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2680
  • Karma: +127/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: Drsstc feedback startup
« Reply #16 on: September 20, 2023, 06:05:54 AM »
Quote
Sadly I am sure the gdt is proper ferrite, I have used this type of core in my 200khz sstc and it was fine, here is a link of it
Material is fine.  How many turns are on your GDT?  Core is rather small for 120kHz.  I'm guessing core is saturating after 5us.  That should be just enough for 120kHz (4us half-cycle).  Not much margin, but probably not the main issue.

Quote
Also, I think the output returning to 0 was some kind of weird glitch with that cheap oscilloscope, my trusty analog scope doesn't show it falling, but staying in the middle
Puzzling, but I'll ignore that one capture showing quick return to Vbus-.  You still might need bleed resistors to keep half-bridge output at half way point.  Without scope load, if upper IGBT happens to have slightly higher leakage current, output may drift high.  Initial start pulse tries to pull it high.  If output is already high, no initial change, so no feedback.

I still suggest scoping UD2.7 51ohm CT burden resistor during that startup pulse, then half-bridge output.
David Knierim

Offline RoamingD

  • High Voltage Enthusiast
  • *
  • Posts: 28
  • Karma: +1/-0
  • Self taught 19yo enthusiast
    • View Profile
Re: Drsstc feedback startup
« Reply #17 on: September 20, 2023, 04:39:36 PM »
Hello, I made a huge discovery, the whole thing works fine when I touch the 2nd or 3rd pin of the AD8561ANZ  ultra fast comparator that I used instead of the lt1001 with the tip of a oscilloscope probe
Now I am confused as to why does this solve the problem and what should I change on the board to make it work by itself
With red is where I probed and it stared working (the ground lead was not connected to anything)
« Last Edit: September 20, 2023, 06:02:04 PM by RoamingD »

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2680
  • Karma: +127/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: Drsstc feedback startup
« Reply #18 on: September 21, 2023, 04:55:53 AM »
Quote
Hello, I made a huge discovery, the whole thing works fine when I touch the 2nd or 3rd pin of the AD8561ANZ  ultra fast comparator that I used instead of the lt1001 with the tip of a oscilloscope probe
Now I am confused as to why does this solve the problem and what should I change on the board to make it work by itself
With red is where I probed and it stared working (the ground lead was not connected to anything)
Scope probe and lead cable are acting as an antenna.  You are picking up enough either random noise or more likely voltage from secondary.  That pickup makes extra driver output transitions to start oscillation.

Three options come to mind for fixing this without a scope probe:

1) Add an antenna.  NOT recommended.  Hard to control what phase lead will be or how much signal may be picked up and over-drive comparitor input.

2) Fix the issue(s) preventing normal startup.  I've already twice suggested next scope measurements to take, so won't repeat here.

3) Modify your driver to be self-oscillating.  I described this for UD2.7 in third paragraph of this post:
    https://highvoltageforum.net/index.php?topic=1373.msg10197#msg10197
David Knierim

Offline Hari33

  • High Voltage Enthusiast
  • *
  • Posts: 19
  • Karma: +0/-0
    • View Profile
Re: Drsstc feedback startup
« Reply #19 on: September 30, 2023, 09:48:42 PM »
Hello, I made a huge discovery, the whole thing works fine when I touch the 2nd or 3rd pin of the AD8561ANZ  ultra fast comparator that I used instead of the lt1001 with the tip of a oscilloscope probe
Now I am confused as to why does this solve the problem and what should I change on the board to make it work by itself
With red is where I probed and it stared working (the ground lead was not connected to anything)


Hi, i am a complete beginner to drsstc, infact i am still in the process of building my first drsstc😅.
But i faced a similar issue while building the driver for my coil.i made Steve Wards 1.3b driver on bread board and it was giving the initial starting pulse only when i was probing the ouput of the mosfet driver.I think its because of the noise getting fixed due to the added capacitence of the probe.
I was able to solve this by connecting a 0.1uf capacitor between the point i probed and the ground.

Hope this helps.
« Last Edit: September 30, 2023, 10:04:08 PM by Hari33 »

High Voltage Forum

Re: Drsstc feedback startup
« Reply #19 on: September 30, 2023, 09:48:42 PM »

 


* Recent Topics and Posts

post Re: LabCoatz Staccato QCW No straight sparks
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
Today at 12:53:22 AM
post Re: LabCoatz Staccato QCW No straight sparks
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
February 21, 2024, 11:37:47 PM
post Re: ESAB Bantam TBH 140 Welder Restoration
[Laboratories, Equipment and Tools]
rikkitikkitavi
February 21, 2024, 10:58:53 PM
post Re: LabCoatz Staccato QCW No straight sparks
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
February 21, 2024, 09:13:05 PM
post Re: LabCoatz Staccato QCW No straight sparks
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
February 21, 2024, 09:04:11 PM
post Re: LabCoatz Staccato QCW No straight sparks
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
February 21, 2024, 08:53:07 PM
post Re: LabCoatz Staccato QCW No straight sparks
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
February 21, 2024, 07:48:47 PM
post Re: LabCoatz Staccato QCW No straight sparks
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
February 21, 2024, 07:28:29 PM
post Re: LabCoatz Staccato QCW No straight sparks
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
February 21, 2024, 06:58:39 PM
post LabCoatz Staccato QCW No straight sparks
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Admiral Aaron Ravensdale
February 21, 2024, 02:31:59 PM
post UD2.7 Thru Hole Capacitor Selection
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
February 21, 2024, 02:30:10 PM
post Re: DIY X-RAY generator made of eBay parts
[X-ray]
PhotonLab
February 20, 2024, 03:14:58 PM
post Re: DIY X-RAY generator made of eBay parts
[X-ray]
alan sailer
February 19, 2024, 06:08:05 PM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
February 19, 2024, 03:03:37 PM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
AstRii
February 19, 2024, 04:34:22 AM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
davekni
February 19, 2024, 04:27:28 AM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
AstRii
February 19, 2024, 03:59:51 AM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
davekni
February 19, 2024, 03:45:51 AM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
February 19, 2024, 03:30:09 AM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
AstRii
February 19, 2024, 02:38:49 AM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
February 19, 2024, 01:52:20 AM
post Re: Lathe Restauration
[General Chat]
TMaxElectronics
February 19, 2024, 12:47:27 AM
post Re: VS-GP250SA60S IGBT suitability - no flywheel diode
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
February 18, 2024, 10:32:36 PM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
February 18, 2024, 10:06:58 PM
post Re: VS-GP250SA60S IGBT suitability - no flywheel diode
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hydron
February 18, 2024, 11:43:44 AM
post Re: VS-GP250SA60S IGBT suitability - no flywheel diode
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
February 18, 2024, 03:41:12 AM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
February 18, 2024, 02:43:37 AM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
February 17, 2024, 10:45:17 PM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
February 17, 2024, 10:29:30 PM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
February 17, 2024, 10:20:39 PM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
February 17, 2024, 10:14:20 PM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
February 17, 2024, 08:56:42 PM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
February 17, 2024, 08:52:45 PM
post Re: DIY X-RAY generator made of eBay parts
[X-ray]
PhotonLab
February 16, 2024, 09:20:44 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
February 16, 2024, 03:50:58 AM
post Re: Ramped DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
February 16, 2024, 03:27:18 AM
post Re: DIY X-RAY generator made of eBay parts
[X-ray]
klugesmith
February 16, 2024, 01:55:48 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
February 15, 2024, 07:11:20 PM
post Re: DIY X-RAY generator made of eBay parts
[X-ray]
PhotonLab
February 15, 2024, 11:31:42 AM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
davekni
February 15, 2024, 06:01:49 AM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
AstRii
February 15, 2024, 05:13:13 AM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
davekni
February 15, 2024, 04:26:00 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
February 14, 2024, 06:25:45 PM
post Re: DIY X-RAY generator made of eBay parts
[X-ray]
Luca c.
February 14, 2024, 03:33:25 PM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
AstRii
February 14, 2024, 12:57:01 PM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
February 14, 2024, 05:32:30 AM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
davekni
February 14, 2024, 05:22:35 AM
post Re: VS-GP250SA60S IGBT suitability - no flywheel diode
[Dual Resonant Solid State Tesla coils (DRSSTC)]
AstRii
February 14, 2024, 04:34:14 AM
post Re: VS-GP250SA60S IGBT suitability - no flywheel diode
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
February 14, 2024, 03:02:16 AM
post Re: RDRSSTC - Project Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
ZakW
February 14, 2024, 01:58:17 AM
post Re: ZCS for SSTC without E class??
[Solid State Tesla Coils (SSTC)]
AstRii
February 13, 2024, 09:30:40 PM
post DIY X-RAY generator made of eBay parts
[X-ray]
PhotonLab
February 13, 2024, 03:54:23 PM
post VS-GP250SA60S IGBT suitability - no flywheel diode
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
February 13, 2024, 09:57:12 AM
post Re: TNY265 flyback issue
[Transformer (Ferrite Core)]
davekni
February 13, 2024, 03:50:05 AM
post Re: TNY265 flyback issue
[Transformer (Ferrite Core)]
AstRii
February 12, 2024, 07:30:42 PM
post Re: PLL "IHFSSTC" concept and schematic
[Solid State Tesla Coils (SSTC)]
Anders Mikkelsen
February 11, 2024, 10:30:38 PM
post Re: Help finding correct IGBT Module
[General Chat]
rikkitikkitavi
February 11, 2024, 09:41:57 PM
post Re: PLL "IHFSSTC" concept and schematic
[Solid State Tesla Coils (SSTC)]
Lucasww
February 11, 2024, 06:34:35 AM
post Re: TNY265 flyback issue
[Transformer (Ferrite Core)]
davekni
February 10, 2024, 03:55:35 AM
post Help finding correct IGBT Module
[General Chat]
cnichols
February 09, 2024, 09:34:13 PM
post TNY265 flyback issue
[Transformer (Ferrite Core)]
AstRii
February 09, 2024, 06:45:46 PM
post Re: Help Sourcing or Debugging My Small HV Module
[Transformer (Ferrite Core)]
michaelrcolton
February 08, 2024, 07:04:07 PM
post ESAB Bantam TBH 140 Welder Restoration
[Laboratories, Equipment and Tools]
Mads Barnkob
February 08, 2024, 06:47:35 PM
post Re: Anyone used iCCFL.com?
[Transformer (Ferrite Core)]
FPS
February 08, 2024, 12:27:47 AM
post Re: PLL "IHFSSTC" concept and schematic
[Solid State Tesla Coils (SSTC)]
Anders Mikkelsen
February 07, 2024, 09:49:11 PM
post Re: Anyone know of a good variable driver?
[Beginners]
NyaaX_X
February 07, 2024, 04:48:02 PM
post Re: Anyone know of a good variable driver?
[Beginners]
FPS
February 07, 2024, 08:17:37 AM
post Re: How much power?
[Spark Gap Tesla Coils (SGTC)]
Terry
February 06, 2024, 10:51:35 PM
post Re: OCXO Reference devolopment - or a story about scaleability
[Radio Frequency]
Mads Barnkob
February 06, 2024, 07:29:29 PM
post Re: Anyone used iCCFL.com?
[Transformer (Ferrite Core)]
MRMILSTAR
February 05, 2024, 05:18:33 AM
post Re: Anyone know of a good variable driver?
[Beginners]
Mads Barnkob
February 04, 2024, 09:16:25 PM
post Re: PLL "IHFSSTC" concept and schematic
[Solid State Tesla Coils (SSTC)]
davekni
February 04, 2024, 09:13:36 PM
post Anyone used iCCFL.com?
[Transformer (Ferrite Core)]
FPS
February 04, 2024, 09:00:30 PM
post Re: Anyone know of a good variable driver?
[Beginners]
FPS
February 04, 2024, 08:56:14 PM
post Re: OCXO Reference devolopment - or a story about scaleability
[Radio Frequency]
Da_Stier
February 04, 2024, 08:18:01 PM
post Re: Anyone know of a good variable driver?
[Beginners]
Mads Barnkob
February 04, 2024, 08:04:36 PM
post OCXO Reference devolopment - or a story about scaleability
[Radio Frequency]
Da_Stier
February 04, 2024, 07:56:55 PM
post Re: PLL "IHFSSTC" concept and schematic
[Solid State Tesla Coils (SSTC)]
Lucasww
February 04, 2024, 08:45:53 AM
post Anyone know of a good variable driver?
[Beginners]
FPS
February 04, 2024, 12:56:52 AM
post Re: looking for a pll sstc schematic with gate driver ic.
[Solid State Tesla Coils (SSTC)]
yourboi
February 03, 2024, 07:01:12 PM
post Re: SSTC bus inductance
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
February 03, 2024, 08:04:29 AM
post Re: SSTC bus inductance
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
February 03, 2024, 06:01:12 AM
post Re: is there a standard pinout of optical audio output connectors?
[Electronic Circuits]
Rafft
February 02, 2024, 05:04:44 PM
post SSTC bus inductance
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
February 02, 2024, 08:34:56 AM
post Re: How much power?
[Spark Gap Tesla Coils (SGTC)]
klugesmith
February 01, 2024, 07:03:41 PM
post Does anyone have a 3d print form for a spiral primary on 4" pvc?
[Solid State Tesla Coils (SSTC)]
yourboi
February 01, 2024, 06:23:45 PM
post Re: How much power?
[Spark Gap Tesla Coils (SGTC)]
Mads Barnkob
February 01, 2024, 07:53:53 AM
post Re: How much power?
[Spark Gap Tesla Coils (SGTC)]
klugesmith
January 31, 2024, 11:43:32 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
Ranni81
January 31, 2024, 08:03:40 PM
post Re: How much power?
[Spark Gap Tesla Coils (SGTC)]
Hysteresis
January 31, 2024, 03:34:48 PM
post Re: How much power?
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
January 31, 2024, 05:08:10 AM
post Re: How much power?
[Spark Gap Tesla Coils (SGTC)]
Mads Barnkob
January 30, 2024, 10:17:45 PM
post How much power?
[Spark Gap Tesla Coils (SGTC)]
Terry
January 30, 2024, 08:07:39 PM
post Ultrasonic Plastic Welding experiments with TA-40CS transducer
[Transformer (Ferrite Core)]
davekni
January 28, 2024, 11:37:30 PM
post Re: is there a standard pinout of optical audio output connectors?
[Electronic Circuits]
yourboi
January 28, 2024, 03:07:12 AM
post Re: First time DRSSTC Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
January 27, 2024, 02:27:29 PM
post Re: Lathe Restauration
[General Chat]
Mads Barnkob
January 27, 2024, 01:26:34 PM
post Re: Determine output voltage of DRSSTC
[General Chat]
Mads Barnkob
January 27, 2024, 01:15:51 PM
post Re: is there a standard pinout of optical audio output connectors?
[Electronic Circuits]
Mads Barnkob
January 27, 2024, 01:13:29 PM
post Determine output voltage of DRSSTC
[General Chat]
Pavol
January 27, 2024, 11:35:35 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal