Author Topic: IGBTs dying silently, but why?  (Read 3793 times)

Offline xxThorx

  • High Voltage Enthusiast
  • *
  • Posts: 4
  • Karma: +0/-0
    • View Profile
IGBTs dying silently, but why?
« on: March 26, 2020, 12:03:43 PM »
Hi everybody,
I'm building my second DRSSTC with this configuration:

Full Bridge of IXGN60N60C2D1
Filter cap: 5100uF 400V
Snubber cap: 2.5uF 1kV
MMC: 149nF made with 3S 3P CDE942C20P15K-F
Primary: 7.5 turns of 6mm copper tube
Frequency: 110kHz
OCD set to 300A (planned 400-450A)
10kohm 50W across outputs
Resistor between GDT and Gate: 10R
Schottky diode between GDT and Gate: 1N5819
Zeners between Emitter and Gate: 28V 3W
GDT made with 10 turns of CAT5 cable over EPCOS N30 toroid

I'm using UD 2.5 driver, with feedback transformers made with turns ratio 1:625 (OCD 5R1, FB 51R)(2x 2 EPCOS N30 toroids)
I've burnt in total 7 IGBTs, they keep failing silently, shorting E, G and C all together.
The first 6 failed with a bus voltage of around 120VDC.
I've tried using 5R1, 8R2 and 10R resistors between Emitter and Gate, with these results (0VDC bus)



After these failures, I've rebuilt the GDT and feedback transformers with the EPCOS N30 toroids (I was using the yellow toroids from an ATX, really wrong choice, I admit).
I thought I had found the source of the failures, but today I've tried pushing the coil to 200VDC, yet another silent failure..
I plan to use it at full power (325VDC, 450A OCD), but I can't keep throwing away IGBTs, as it take 1 month to arrive from China..
For Phase Lead I'm currently using Coilcraft 7m3 153 inductors (maybe I have to tune it better?)
I'll attach some pictures of my overall setup
Does somebody have any suggestion?
Best regards
Daniel Rinni

IMAGES:


















Offline oneKone

  • High Voltage Engineer
  • ****
  • Posts: 337
  • Karma: +14/-0
    • View Profile
Re: IGBTs dying silently, but why?
« Reply #1 on: March 26, 2020, 01:39:17 PM »
welcome to the forum!

When i built my first drsstc i also used chinese ixgn60n60 devices, Like you i had zero success with them. I think i killed like 12 of them before i gave up. In the end i ended up ordering genuine 'nos' (bit of a stretch calling them that :) ) devices, they were expensive but they worked flawlessly.

imo if you can (and i definitely don't want to deter you from using the packages you want) have a look at skm modules from aliexpress, I've successfully used skm100gb in a fullbridge at 650a @ 180khz, although now they're sitting at 500a limit.

these are the ones i ordered:
https://www.aliexpress.com/item/32226740068.html?spm=a2g0o.productlist.0.0.48205ec3N0Us4f&algo_pvid=adc8b0d0-59f2-4b2e-9e15-c57bf2dfb687&algo_expid=adc8b0d0-59f2-4b2e-9e15-c57bf2dfb687-1&btsid=0ab6f81615852262872864010e4291&ws_ab_test=searchweb0_0,searchweb201602_,searchweb201603_

sorry i couldn't give the answer you were looking for,     


Offline xxThorx

  • High Voltage Enthusiast
  • *
  • Posts: 4
  • Karma: +0/-0
    • View Profile
Re: IGBTs dying silently, but why?
« Reply #2 on: March 26, 2020, 03:11:10 PM »
Thank you very much for your answer!
Well, it is quite strange that all these modules have broken, and they all come from China..
I read that also Mads have had some problems with these modules, were these also from China, brand new? Or they were an old stock..?
It should be a discontinued/obsolete product, maybe they're producing them again, but not with the same quality?

Anyway, I will consider switching to these half bridge modules, but first I would like to search some similar modules with the same package, I don't really want to rebuild the aluminium busbars, they're laser cut 😅
Any suggestions on similar, not discontinued IGBTs?

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2744
  • Karma: +129/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: IGBTs dying silently, but why?
« Reply #3 on: March 26, 2020, 06:49:18 PM »
I'll agree that counterfeit Chinese parts are the most likely cause.  As you mentioned, drive phasing is another possible cause.  That you can measure with your scope.

One small point that isn't likely to be a real problem:  Those IGBT packages are intended to have one emitter terminal used for the power connection and the other for gate return.  It's better not to have connections between the two emitter terminals outside of the IGBT package itself.  Outside connections add some of the voltage drop (due to parasitic inductance) to the gate-drive signal.  Your connections are with aluminum bars directly on the packages, so not likely an issue.  I'd still suggest leaving off those little bars.

I couldn't tell from the images just how much wiring inductance there may be between the 2.5uF snubber cap and the bulk filter cap.  With 600V IGBTs, inductance there can be problematic at the end of each enable pulse, when the H-Bridge changes from drawing power to sourcing power (from the Tesla primary back to the bulk supply).  I had to redo my bulk-cap wiring for that reason, as my DRSSTC also uses 600V parts (10x TO247 for each leg).  Bulk cap inductance makes a large voltage spike on the snubber at that end-of-enable transition.  Try scoping across the snubber and triggering off the trailing enable edges.

Final note:  For future posts, would you mind uploading pictures directly to this forum rather than linking?  The linked image host has intrusive advertising, and was initially blocked by my anti-virus software.
David Knierim

Offline xxThorx

  • High Voltage Enthusiast
  • *
  • Posts: 4
  • Karma: +0/-0
    • View Profile
Re: IGBTs dying silently, but why?
« Reply #4 on: March 26, 2020, 09:23:35 PM »
I'll agree that counterfeit Chinese parts are the most likely cause.  As you mentioned, drive phasing is another possible cause.  That you can measure with your scope.
Here are some scope shots, I've changed the burnt IGBT with a new one.




Yellow trace is the DC bus voltage (210VDC, peaks of 384V), blue trace is one output of the full bridge. I've tried every setting for the phase lead, I really can't get rid of these huge spikes, maybe I need a smaller inductor.. or maybe it is caused by the same input?
However, 384V peaks should be under the 600V IGBT rating, hence I don't think it is the real problem here.. right?



One small point that isn't likely to be a real problem:  Those IGBT packages are intended to have one emitter terminal used for the power connection and the other for gate return.  It's better not to have connections between the two emitter terminals outside of the IGBT package itself.  Outside connections add some of the voltage drop (due to parasitic inductance) to the gate-drive signal.  Your connections are with aluminum bars directly on the packages, so not likely an issue.  I'd still suggest leaving off those little bars.
I'll do it in my next coil, thank you very much for the suggestion! I can't do it in this one because I can't modify the negative side, I would remove too much material to leave uncovered the emitter for the gate return..

I couldn't tell from the images just how much wiring inductance there may be between the 2.5uF snubber cap and the bulk filter cap.  With 600V IGBTs, inductance there can be problematic at the end of each enable pulse, when the H-Bridge changes from drawing power to sourcing power (from the Tesla primary back to the bulk supply).  I had to redo my bulk-cap wiring for that reason, as my DRSSTC also uses 600V parts (10x TO247 for each leg).  Bulk cap inductance makes a large voltage spike on the snubber at that end-of-enable transition.  Try scoping across the snubber and triggering off the trailing enable edges.
I'll post another picture of the rectifying assembly:



could it be the problem?
Code for the filtering capacitor is ALS70A512MF400, code for the snubber is C4BSNBX4250ZAMJ


PS: I don't know why, but I don't manage to put the pictures in the right direction  :-X
« Last Edit: March 26, 2020, 09:44:05 PM by xxThorx »

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2744
  • Karma: +129/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: IGBTs dying silently, but why?
« Reply #5 on: March 27, 2020, 12:55:38 AM »
I'll take up-side-down images over the links.  It's not hard to invert them during viewing.

I agree that the bus voltage ring is not likely the issue, at least not the lower-frequency peak that I had problems with.  Thank you for the image;  I now see that the bulk cap is bolted to your bus bars, not at the other end of the cables as I was initially thinking.  That is good.

It's hard to tell phase lead based on the attached scope traces.  H-Bridge output phase appears to be roughly at the current zero-crossings.  Slightly before current zero-crossing is ideal, so slightly more phase lead.  More phase lead requires a larger inductance on the driver board.  (I have UD2.7 schematics, so am presuming that UD2.5 is similar.)  Hopefully phasing the H-Bridge output slightly before current zero-crossing will reduce the spikes.  It usually does.  It is possible that those high-frequency spikes are even higher voltage at the IGBT die themselves than where you can scope.  If the spikes can be reduced by adding a bit more phase lead, that might make the IGBTs last longer.
David Knierim

Offline xxThorx

  • High Voltage Enthusiast
  • *
  • Posts: 4
  • Karma: +0/-0
    • View Profile
Re: IGBTs dying silently, but why?
« Reply #6 on: April 04, 2020, 04:07:16 PM »
Little update:
I tried adding another 1.5KE440CA TVS between the snubber cap, to decrease any transient voltage.
It worked well for a while at 200BPS, 60us on-time, 300A OCD, I even managed to reach 325VDC input voltage for 5 minutes, until.. quite a nice explosion, it broke in half an IGBT.
It was the only IGBT I had in the bridge from 5 years ago, a used one.. which was quite suspectful.
The other 3 IGBTs appeared to be shorted between all the ports, so I decided to do an autopsy on the different IGBTs, which revealed a different package, with probably inferior quality and design compared to old ones.. I think that 2-3 IGBTs failed short, leaving the other one do all the job. In conclusion, looks like the diode semiconductor failed, exploding

(Bottom, short-failing, new IGBT. Top, exploded, old IGBT. Notice the different internal config and the different labeling)



In conclusion, I discarded completely these IGBTs, since I can't find any reliable component source, and accepted oneKone suggestion.
I'll buy two used SKM100GB125DN modules, add another bus cap to increase ripple current from 22.3A to 44.6A (10kHz), rebuild the full bridge with aluminium laminated busbars and hope for the best!
« Last Edit: April 04, 2020, 04:10:01 PM by xxThorx »

High Voltage Forum

Re: IGBTs dying silently, but why?
« Reply #6 on: April 04, 2020, 04:07:16 PM »

 


* Recent Topics and Posts

post Re: Big Coil Build Log
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
Today at 05:47:34 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
davekni
Today at 04:45:07 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
Today at 04:18:27 AM
post Push Pull VTTC
[Vacuum Tube Tesla Coils (VTTC)]
janno288
Today at 01:10:08 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 27, 2024, 10:54:52 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 27, 2024, 11:53:42 AM
post Re: OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 05:14:36 AM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:47:48 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:41:59 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 27, 2024, 12:04:34 AM
post Re: Super flat QCW simulation (does this look reasonable?)
[Dual Resonant Solid State Tesla coils (DRSSTC)]
toooldforthis
March 26, 2024, 11:08:14 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 11:07:20 PM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 10:46:29 PM
post OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 26, 2024, 09:03:43 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 08:46:59 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 26, 2024, 05:02:18 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 03:16:03 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 26, 2024, 01:41:49 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 04:48:22 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 26, 2024, 04:16:37 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 26, 2024, 04:16:24 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 26, 2024, 04:13:02 AM
post Re: CM400 Induction Heater
[Electronic Circuits]
davekni
March 26, 2024, 04:00:43 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
davekni
March 26, 2024, 03:19:18 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
March 26, 2024, 01:50:42 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 08:05:02 PM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 25, 2024, 07:41:29 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 06:45:46 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 05:44:25 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 25, 2024, 04:47:17 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 04:27:22 PM
post Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 25, 2024, 03:57:34 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 25, 2024, 02:06:41 PM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 04:43:25 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
davekni
March 25, 2024, 02:39:40 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 12:47:09 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 24, 2024, 07:36:32 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
Alberto
March 24, 2024, 07:27:24 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 24, 2024, 04:25:23 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 10:47:35 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 09:30:21 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 04:34:31 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 03:04:25 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 01:38:34 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 04:20:03 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 23, 2024, 12:54:30 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 23, 2024, 12:05:57 AM
post capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 22, 2024, 11:45:03 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 22, 2024, 11:30:09 PM
post Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 22, 2024, 10:20:35 PM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Benbmw
March 22, 2024, 09:21:13 PM
post Re: What actually kills MOSFETs?
[Beginners]
AstRii
March 22, 2024, 03:37:11 PM
post What actually kills MOSFETs?
[Beginners]
FPS
March 22, 2024, 05:09:20 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 22, 2024, 03:57:54 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 22, 2024, 02:59:25 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 06:31:42 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
rikkitikkitavi
March 21, 2024, 03:08:01 PM
post Re: [WTS] IGBT, Ferrite, Capacitors, Tools, PSU, Industrial components and parts
[Sell / Buy / Trade]
Mads Barnkob
March 21, 2024, 01:37:32 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Alberto
March 21, 2024, 11:42:07 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 21, 2024, 04:09:14 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 02:15:31 AM
post My Homemade Structural Analysis X-Ray Machine
[X-ray]
Luca c.
March 21, 2024, 01:35:40 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 20, 2024, 10:40:00 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Mads Barnkob
March 20, 2024, 08:03:41 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Mads Barnkob
March 20, 2024, 07:51:57 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 20, 2024, 10:39:47 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 20, 2024, 04:09:59 AM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 20, 2024, 01:13:23 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
March 20, 2024, 12:45:16 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 20, 2024, 12:30:30 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 11:12:24 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:47:49 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:44:19 PM
post Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 19, 2024, 06:52:09 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 19, 2024, 05:02:44 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
Mads Barnkob
March 19, 2024, 05:01:41 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 04:31:02 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 03:59:54 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 06:41:39 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 19, 2024, 04:05:49 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 18, 2024, 09:08:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 09:07:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
Twospoons
March 18, 2024, 08:57:06 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
MRMILSTAR
March 18, 2024, 03:51:33 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:59:46 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:33:25 PM
post Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 11:02:12 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Twospoons
March 18, 2024, 02:36:11 AM
post Re: Best forum for vacuum tube amplifiers?
[General Chat]
Mads Barnkob
March 17, 2024, 07:42:55 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:15:14 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 05:05:04 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
davekni
March 17, 2024, 04:50:51 AM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Twospoons
March 17, 2024, 04:45:17 AM
post 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:17:51 AM
post Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Terry
March 17, 2024, 01:29:32 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 17, 2024, 12:33:06 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
March 16, 2024, 08:46:20 PM
post Re: Bleeder resistor for MMC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hydron
March 16, 2024, 08:39:24 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hydron
March 16, 2024, 08:21:44 PM
post Best forum for vacuum tube amplifiers?
[General Chat]
yourboi
March 16, 2024, 08:20:13 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal