High Voltage Forum
High voltage => Transformer (Ferrite Core) => Topic started by: AlexanderHun on September 14, 2019, 05:05:00 PM
-
Hello!
I would like to ask you, who has made several high voltage transformers here? I was experimenting with television flyback transformers, it could produce a piece of 30kV. They can be connected in series but I want to make my own, my goal is at least 60kV. Do you think this is possible? Included are two forms of what ferrite core I found, so I should design a secondary one.
(https://i.postimg.cc/XXfg6SBy/f1.jpg) (https://postimg.cc/XXfg6SBy)
(https://i.postimg.cc/vxsk8rv7/f2.jpg) (https://postimg.cc/vxsk8rv7)
I drive with this switch ..
https://cdn.instructables.com/FSW/2MIC/GNBEVVKF/FSW2MICGNBEVVKF.LARGE.jpg?auto=webp&&frame=1 (https://cdn.instructables.com/FSW/2MIC/GNBEVVKF/FSW2MICGNBEVVKF.LARGE.jpg?auto=webp&&frame=1)
I have a 3d printer, I could print what I need, but unfortunately I haven't designed one yet. I will need to drive an X-ray tube, then I want to apply a voltage multiplier.
-
https://highvoltageforum.net/index.php?topic=390.0 (https://highvoltageforum.net/index.php?topic=390.0)
consider making a bobbin
-
Thanks! I don't see any specific electrical voltage, nor is it written by any person who built one. Do they measure voltage? I see a 14-20kV post, but it is very little for me
-
Hi :)
what core is in the picture ?
I have the same project, but with a lower voltage (20kV)
I suggest for the bobbin a milled HDPE cylinder because 3d printed coils have air bubble, so partial discharges can occur
cheers
-
Thanks for the help! I have a dental X-ray and I want to operate an X-ray tube. The question is how much tension to multiply, what do I manage to produce for myself.
Philips oralix dental x-ray head:
(https://i.postimg.cc/ppsHzgmn/20190810-131709.jpg) (https://postimg.cc/ppsHzgmn)
I usually do X-ray fluoroscopy videos, this is my own:
https://www.youtube.com/watch?v=3kqrlqLzQrE (https://www.youtube.com/watch?v=3kqrlqLzQrE)
The tube I want to operate requires 60kV: (I'd like to operate this tube)
(https://i.postimg.cc/pphZJjTY/cs3.jpg) (https://postimg.cc/pphZJjTY)
This is a "siemens röntgenkugel" x-ray tube
(https://i.postimg.cc/v1rMgDfG/ER10.jpg) (https://postimg.cc/v1rMgDfG)
-
Presuming you need 60V DC, it's probably easier to use a somewhat-lower-voltage transformer and a voltage multiplier. For my Marx generator, I wound a +-11kV transformer followed by a voltage multiplier to get +-22kV DC
-
Hi! Today I experimented a bit, I have a lot of quarantine due to the coronavirus, I got this with two flyback transformers. Measurement coming soon, the voltage divider has been made ...
https://www.youtube.com/watch?v=XpStl-phy7w (https://www.youtube.com/watch?v=XpStl-phy7w)
-
Is that with primaries in parallel and secondaries in series?
-
I made a 250kV x-ray psu a few years back
i used a max of 7kV from the transformer. Formers very similar to what has been already linked except i had the primary under the secondary. The secondary a press fit over the primary former. 12 turn primary driven by an audio amplifier running +-48 volt rails @ 20 khz
The 7 kv supply fed the center of of a full wave cockcroft walton multiplier one multiplier going each way so that I had the actual transformer feeding inin the centerof the multiplier with the multiplier capas doubled in value for the first two stages in each direction
more info here http://www.coultersmithing.com/forums/viewtopic.php?f=9&t=98