Author Topic: Anyone tried resonant NST?  (Read 4980 times)

Offline AstRii

  • High Voltage Engineer
  • ****
  • Posts: 260
  • Karma: +9/-0
  • Czech Technical University in Prague
    • View Profile
    • UHVlab - Tesla Coils | High Voltage | Education
Anyone tried resonant NST?
« on: August 30, 2020, 01:42:12 AM »
Hey!
I was wondering... You can see so many people making arcs with resonant MOTs, has anyone tried to do the same with NSTs?
Unlike MOTs they have very low output currents, but maybe with resonant capacitors, the arcs could be monstrous :) (maybe even try to parallel a few of those for higher currents? :D)

I have only seen very few attempts of trying resonant NST arcs, and with almost no details or information about it.
Is there any reason to why not try resonance with NSTs?
Bc. Marek Novotny
Czech Republic, Czech Technical University in Prague
www.uhvlab.org

Offline Mads Barnkob

  • Administrator
  • Executive Board Member
  • *****
  • Posts: 2269
  • Karma: +71/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Anyone tried resonant NST?
« Reply #1 on: August 30, 2020, 01:15:46 PM »
You will see from SGTC builders that sizing of the MMC for such a Tesla Coil is aimed at a term called Larger-Than-Resonant and is a term to design the MMC to NOT resonate with the NST secondary inductance, as it will destroy the transformer from over-voltage.

The MOT only has about 2 kVAC output whereas the MST has 9-15 kVAC, but with wire with about the same voltage rating, the MOT is much more robust against over-voltage than the NST is.
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline AstRii

  • High Voltage Engineer
  • ****
  • Posts: 260
  • Karma: +9/-0
  • Czech Technical University in Prague
    • View Profile
    • UHVlab - Tesla Coils | High Voltage | Education
Re: Anyone tried resonant NST?
« Reply #2 on: August 30, 2020, 01:21:21 PM »
Oh, is the voltage really rising so high?
Because MOT capacitors are rated ~2.1kVAC, yet people very often use only 1 series capacitor (and 2-3 in parallel) for MOT resonance.
Why is it that the capacitors survive?
Bc. Marek Novotny
Czech Republic, Czech Technical University in Prague
www.uhvlab.org

Offline davekni

  • Executive Board Member
  • *******
  • Posts: 2745
  • Karma: +130/-1
  • Physicist, engineer (electronic), and hobbiest
    • View Profile
Re: Anyone tried resonant NST?
« Reply #3 on: August 30, 2020, 06:36:53 PM »
There are smaller NSTs for small signs with lower voltage, down to 3kV.  Those are usually lower current too (for smaller neon tube diameter), so not of much interest for SGTC or arcs.

Especially with AC use, capacitor failure isn't typically instantaneous,.  Failure occurs with localized corona or similar dielectric breakdown at field concentration points within the capacitor.  This breakdown doesn't initially extend all the way to the opposite plate, just very locally at the sharp edge or corner.  Over use time, the insulation degrades and spreads until failure.  So, capacitor lifetime is more of an exponential function of voltage than an abrupt function.

Most MOT arc experiments last no more than a few seconds or minutes.  The caps would not survive long-term use in such over-voltage conditions.
David Knierim

Offline AstRii

  • High Voltage Engineer
  • ****
  • Posts: 260
  • Karma: +9/-0
  • Czech Technical University in Prague
    • View Profile
    • UHVlab - Tesla Coils | High Voltage | Education
Re: Anyone tried resonant NST?
« Reply #4 on: August 30, 2020, 10:59:51 PM »
Interesting..
When i find some spare time, i will measure the voltage of resonant MOT.
I'm curious :D
Bc. Marek Novotny
Czech Republic, Czech Technical University in Prague
www.uhvlab.org

Offline DashApple

  • High Voltage Enthusiast
  • *
  • Posts: 29
  • Karma: +1/-0
    • View Profile
Re: Anyone tried resonant NST?
« Reply #5 on: August 31, 2020, 03:02:16 PM »
I have tried it , Three 6.3Kv NST's with a 200nF resonant capacitor ( 5 MOT caps in series ) All three get warm rather quickly   

« Last Edit: August 31, 2020, 03:07:14 PM by DashApple »

Offline AstRii

  • High Voltage Engineer
  • ****
  • Posts: 260
  • Karma: +9/-0
  • Czech Technical University in Prague
    • View Profile
    • UHVlab - Tesla Coils | High Voltage | Education
Re: Anyone tried resonant NST?
« Reply #6 on: August 31, 2020, 07:33:55 PM »
That's so sick!
Thank you for sharing.

Bc. Marek Novotny
Czech Republic, Czech Technical University in Prague
www.uhvlab.org

Offline klugesmith

  • High Voltage Senior
  • *****
  • Posts: 688
  • Karma: +22/-0
    • View Profile
Re: Anyone tried resonant NST?
« Reply #7 on: September 01, 2020, 02:36:45 AM »
Thank you.  Reminds me how making arcs with high voltage transformers could be fun. But take it easy with the arcs if you intend to use the transformer for something more productive. :-)

How did you choose the capacitance value?

Did you happen to measure the primary current while making those arcs?   
That might benefit someone here, who recently wondered how a NST could ever draw more current than it would with short circuit on output.

« Last Edit: September 01, 2020, 02:51:02 AM by klugesmith »

Offline DashApple

  • High Voltage Enthusiast
  • *
  • Posts: 29
  • Karma: +1/-0
    • View Profile
Re: Anyone tried resonant NST?
« Reply #8 on: September 06, 2020, 04:16:45 PM »
Thanks

I never measured the primary current when i tried this as it was just a quick setup and for sizing the capacitor it was just trial and error for the most part : )


Offline johnf

  • High Voltage Technician
  • ***
  • Posts: 192
  • Karma: +6/-0
    • View Profile
Re: Anyone tried resonant NST?
« Reply #9 on: September 07, 2020, 11:31:27 AM »
Series resonant circuits can be scary
I did a job for a startup that was making a superconducting magnet for a beam scanning system.
upshot was that an audio amp of 1kW was used to sinewave drive the magnet at approx 100Hz.
the amp was connected by a 25:1 turns ratio transformer to the series tuned circuit. The capacitors required were 20kV rated Plastic capacitors inc units. yep you guessed it we did puncture a few expensive caps due to voltage over excursion.
This is the extreme case with very high Q but similar can be expected with trying to resonate NSTs albeit with much lower Q and higher drive voltage.

Offline Mads Barnkob

  • Administrator
  • Executive Board Member
  • *****
  • Posts: 2269
  • Karma: +71/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Anyone tried resonant NST?
« Reply #10 on: September 07, 2020, 09:22:53 PM »
Oh, is the voltage really rising so high?
Because MOT capacitors are rated ~2.1kVAC, yet people very often use only 1 series capacitor (and 2-3 in parallel) for MOT resonance.
Why is it that the capacitors survive?

MOT capacitors are designed for abuse. I do not have a datasheet at hand, but got a copied table of specifications on my article on a MOT capacitor bank here: http://kaizerpowerelectronics.dk/pulse-power/333-joule-moc-capacitor-bank/

They are tested with 9030 VDC for 60 seconds between terminals.

I have tried it , Three 6.3Kv NST's with a 200nF resonant capacitor ( 5 MOT caps in series ) All three get warm rather quickly   

/>

I would argue that these do NOT count as regular NSTs :) Very nice arcs, but those huge iron cores with separated windings is a whole other level from the small casted resin units seen outside on buildings.
« Last Edit: September 07, 2020, 09:24:58 PM by Mads Barnkob »
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline johnnyzoo

  • High Voltage Enthusiast
  • *
  • Posts: 35
  • Karma: +2/-0
    • View Profile
Re: Anyone tried resonant NST?
« Reply #11 on: September 09, 2020, 11:25:39 AM »
 
Series resonant circuits can be scary
I did a job for a startup that was making a superconducting magnet for a beam scanning system.
upshot was that an audio amp of 1kW was used to sinewave drive the magnet at approx 100Hz.
the amp was connected by a 25:1 turns ratio transformer to the series tuned circuit. The capacitors required were 20kV rated Plastic capacitors inc units. yep you guessed it we did puncture a few expensive caps due to voltage over excursion.
This is the extreme case with very high Q but similar can be expected with trying to resonate NSTs albeit with much lower Q and higher drive voltage.

Hmmm... superconducting tesla coil, anyone? :o

Offline abstruse1

  • High Voltage Technician
  • ***
  • Posts: 131
  • Karma: +1/-0
    • View Profile
Re: Anyone tried resonant NST?
« Reply #12 on: September 04, 2021, 04:51:28 PM »
I hope this question is not a hijacking of this thread. It seems to me that these truly spectacular flame arcs are not the result of especially high voltage. You’ll notice that the spoon had to almost touch the other terminal to get the arc started. One interpretation of this is that the voltage is pretty low but the power is very high, easily ionizing a lot of air which gets the arc growing. Or maybe the resonance phenomenon (high voltage) doesn’t begin until the current starts flowing, after which it takes over, big-time.

 What am I missing?
Abstruse1
   Been working with electricity for 60 years and still getting a tingle!

Offline AstRii

  • High Voltage Engineer
  • ****
  • Posts: 260
  • Karma: +9/-0
  • Czech Technical University in Prague
    • View Profile
    • UHVlab - Tesla Coils | High Voltage | Education
Re: Anyone tried resonant NST?
« Reply #13 on: September 28, 2021, 10:44:30 PM »
You are right, the voltage doesn't have to be high to create large arcs.
This is my setup with multiple MOTs and resonant capacitors:


This setup produces ~4kV. The electrodes need to be millimeters apart to start the arc.
But the higher current creates much more conductive plasma channel which is easier to sustain over big distances.

With this setup I was able to stretch over a meter long arc with only a few kV (but more than 16kVA of power).

Even though most NSTs generate larges voltages (up to 12kV) their power is much lower (~400VA) and therefore create only "small" arcs.

In general, if you want bigger output, you need bigger power. You cannot magically create large hot arc with a few Watts of power. 
Theoretically you don't even need high voltage to make huge arc.
Bc. Marek Novotny
Czech Republic, Czech Technical University in Prague
www.uhvlab.org

High Voltage Forum

Re: Anyone tried resonant NST?
« Reply #13 on: September 28, 2021, 10:44:30 PM »

 


* Recent Topics and Posts

post Re: Kaizer VTTC 1
[Vacuum Tube Tesla Coils (VTTC)]
Mads Barnkob
Today at 10:23:02 AM
post Re: Capacitor in Parallel with Primary Coil
[Beginners]
Mads Barnkob
Today at 10:17:34 AM
post Capacitor in Parallel with Primary Coil
[Beginners]
FPS
Today at 10:01:41 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
Today at 04:47:35 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
davekni
Today at 03:59:27 AM
post Re: Kaizer VTTC 1
[Vacuum Tube Tesla Coils (VTTC)]
MRMILSTAR
March 28, 2024, 09:15:11 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 28, 2024, 01:01:12 PM
post Re: Big Coil Build Log
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 28, 2024, 05:47:34 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
davekni
March 28, 2024, 04:45:07 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 28, 2024, 04:18:27 AM
post Push Pull VTTC
[Vacuum Tube Tesla Coils (VTTC)]
janno288
March 28, 2024, 01:10:08 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 27, 2024, 10:54:52 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 27, 2024, 11:53:42 AM
post Re: OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 05:14:36 AM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:47:48 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:41:59 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 27, 2024, 12:04:34 AM
post Re: Super flat QCW simulation (does this look reasonable?)
[Dual Resonant Solid State Tesla coils (DRSSTC)]
toooldforthis
March 26, 2024, 11:08:14 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 11:07:20 PM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 10:46:29 PM
post OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 26, 2024, 09:03:43 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 08:46:59 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 26, 2024, 05:02:18 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 03:16:03 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 26, 2024, 01:41:49 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 04:48:22 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 26, 2024, 04:16:37 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 26, 2024, 04:16:24 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 26, 2024, 04:13:02 AM
post Re: CM400 Induction Heater
[Electronic Circuits]
davekni
March 26, 2024, 04:00:43 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
davekni
March 26, 2024, 03:19:18 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
March 26, 2024, 01:50:42 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 08:05:02 PM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 25, 2024, 07:41:29 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 06:45:46 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 05:44:25 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 25, 2024, 04:47:17 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 04:27:22 PM
post Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 25, 2024, 03:57:34 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 25, 2024, 02:06:41 PM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 04:43:25 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
davekni
March 25, 2024, 02:39:40 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 12:47:09 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 24, 2024, 07:36:32 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
Alberto
March 24, 2024, 07:27:24 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 24, 2024, 04:25:23 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 10:47:35 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 09:30:21 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 04:34:31 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 03:04:25 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 01:38:34 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 04:20:03 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 23, 2024, 12:54:30 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 23, 2024, 12:05:57 AM
post capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 22, 2024, 11:45:03 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 22, 2024, 11:30:09 PM
post Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 22, 2024, 10:20:35 PM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Benbmw
March 22, 2024, 09:21:13 PM
post Re: What actually kills MOSFETs?
[Beginners]
AstRii
March 22, 2024, 03:37:11 PM
post What actually kills MOSFETs?
[Beginners]
FPS
March 22, 2024, 05:09:20 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 22, 2024, 03:57:54 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 22, 2024, 02:59:25 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 06:31:42 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
rikkitikkitavi
March 21, 2024, 03:08:01 PM
post Re: [WTS] IGBT, Ferrite, Capacitors, Tools, PSU, Industrial components and parts
[Sell / Buy / Trade]
Mads Barnkob
March 21, 2024, 01:37:32 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Alberto
March 21, 2024, 11:42:07 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 21, 2024, 04:09:14 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 02:15:31 AM
post My Homemade Structural Analysis X-Ray Machine
[X-ray]
Luca c.
March 21, 2024, 01:35:40 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 20, 2024, 10:40:00 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Mads Barnkob
March 20, 2024, 08:03:41 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Mads Barnkob
March 20, 2024, 07:51:57 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 20, 2024, 10:39:47 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 20, 2024, 04:09:59 AM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 20, 2024, 01:13:23 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
March 20, 2024, 12:45:16 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 20, 2024, 12:30:30 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 11:12:24 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:47:49 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:44:19 PM
post Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 19, 2024, 06:52:09 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 19, 2024, 05:02:44 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
Mads Barnkob
March 19, 2024, 05:01:41 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 04:31:02 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 03:59:54 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 06:41:39 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 19, 2024, 04:05:49 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 18, 2024, 09:08:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 09:07:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
Twospoons
March 18, 2024, 08:57:06 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
MRMILSTAR
March 18, 2024, 03:51:33 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:59:46 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:33:25 PM
post Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 11:02:12 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Twospoons
March 18, 2024, 02:36:11 AM
post Re: Best forum for vacuum tube amplifiers?
[General Chat]
Mads Barnkob
March 17, 2024, 07:42:55 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:15:14 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 05:05:04 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
davekni
March 17, 2024, 04:50:51 AM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Twospoons
March 17, 2024, 04:45:17 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal