Author Topic: PCB etching, DIY (chemistry mostly)  (Read 6067 times)

Offline afk

  • High Voltage Enthusiast
  • *
  • Posts: 30
  • Karma: +0/-0
    • View Profile
PCB etching, DIY (chemistry mostly)
« on: April 11, 2017, 01:45:02 PM »
Hi guys,

Not so relevant to our usual high voltage stuffs, I'd like to consult you about etching PCB via chemical process (which is cheap!)

Though I'm not really good with chemistry, luckily for PCB etching it is not about organic chemistry (yay).

I am using Copper (II) Chloride solution by using Hydrochloric Acid taking copper directly from the board, with hydrogen peroxide as oxidizer. As you know, CuCl2 takes copper from the board to become Cupric Chloride. This solution can be reusable by bubbling air (oxygen) into the solution with more Hydrochloric Acid, turning CuCl back to CuCl2.

However, the etching speed is really slow. It took me 10 hours to clear up around 9 cm² of copper, which is so darn long. I even had to heat the solution up but it did not speed up much. On the copper tracks that needs removing, it turns dark-colored and it seems that I have to rub them off to speed up the etching (I suspect this is copper oxide that is resulted from copper and peroxide, but it is strange as it isn't solved by acid). It is very time-consuming and inconvenient. Even worse, the longer I leave the PCB in, the chemicals will start to attack the part that I don't want to be removed.

I don't etch PCB much, but I sometimes have to do it, so I need to improve my solution for my future usage. Some DIY sites don't have much information to solve this problem for me; their etching speed doesn't look this long.

Anyone here can help me with this problem?

Offline Mads Barnkob

  • Administrator
  • Executive Board Member
  • *****
  • Posts: 2267
  • Karma: +71/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: PCB etching, DIY (chemistry mostly)
« Reply #1 on: April 11, 2017, 10:36:57 PM »
I only know your problems from using a too thin, saturated or cold Iron(III) chloride / ferric chloride solution.

They are weak acids for copper etching, but they are also relatively harmless, but will colour your clothes for life :) I have a solution that I have been using for years and with the small amount of boards I etch, its still the most cheap way.

I recently bought some Sodium persulfate, but have not yet tried it out.

I will make a thread on toner transfer method and etching later when I have time
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline futurist

  • Global Moderator
  • High Voltage Engineer
  • *****
  • Posts: 203
  • Karma: +8/-0
    • View Profile
Re: PCB etching, DIY (chemistry mostly)
« Reply #2 on: April 12, 2017, 02:12:03 AM »
I etched my PCBs in hydrochloric acid/hydrogen peroxide mixture which went down the drain after each use
Recovery isn't worth the trouble, you probably won't etch that many PCBs and both of the chemicals are cheap as hell

Unfortunately I can't find the ratio I used, but you could experiment with various ones found on the internet
Etching solutions are easy to debug; when I had problems (etching taking too long, copper delaminating, etc.) I would make small dummy boards with lines of various thickness, to avoid ruining real ones

Offline afk

  • High Voltage Enthusiast
  • *
  • Posts: 30
  • Karma: +0/-0
    • View Profile
Re: PCB etching, DIY (chemistry mostly)
« Reply #3 on: April 13, 2017, 07:09:40 AM »
I etched my PCBs in hydrochloric acid/hydrogen peroxide mixture which went down the drain after each use
Recovery isn't worth the trouble, you probably won't etch that many PCBs and both of the chemicals are cheap as hell

Unfortunately I can't find the ratio I used, but you could experiment with various ones found on the internet
Etching solutions are easy to debug; when I had problems (etching taking too long, copper delaminating, etc.) I would make small dummy boards with lines of various thickness, to avoid ruining real ones

I use CuCl2 not for recovery, but mostly to avoid treating the waste by reusing the chemicals again.

You are using HCl and H2O2 like me, and adding CuCl/CuCl2 as the products of etching, it sounds like a good way to destroy your drain system. I don't know about your drain system, but most drainage pipes are made of copper, and this mixture can "etch" your pipe, wearing them down fast.

Copper in CuCl/CuCl2 are also toxic and harmful to the environment; dumping it into your drain or into your garden without treating is bad.

Since there is no dedicated service for treating chemical waste in where I live, I have to take care of everything.

Offline futurist

  • Global Moderator
  • High Voltage Engineer
  • *****
  • Posts: 203
  • Karma: +8/-0
    • View Profile
Re: PCB etching, DIY (chemistry mostly)
« Reply #4 on: April 13, 2017, 01:56:05 PM »
Don't worry about copper waste, it isn't mercury.. 1 oz PCB has ~300 g/m^2 of copper, so common 10x10 cm PCB has just 3 g of copper - and you don't etch all of it
And as far as I know drain pipes were never made out of copper.. you will more likely damage the plumbing and environment with acidic/caustic drain cleaners than with diluted etching solution

Offline Morvandium

  • High Voltage Enthusiast
  • *
  • Posts: 4
  • Karma: +0/-0
    • View Profile
Re: PCB etching, DIY (chemistry mostly)
« Reply #5 on: July 10, 2020, 11:06:07 PM »
And as far as I know drain pipes were never made out of copper.

Plumbers started using copper drain line (in the US) in the 1930s (plumbers preferred it to much heavier cast-iron), though copper really didn't catch on until the '60s for drain lines.  I've read Chicago required them at least as recently as 2006.  There's 20+feet of copper drain line in my basement (the rest was cast iron, but my repairs are PVC), and it was built in the '70s.

Don't know about other parts of the world.

Offline klugesmith

  • High Voltage Senior
  • *****
  • Posts: 688
  • Karma: +22/-0
    • View Profile
Re: PCB etching, DIY (chemistry mostly)
« Reply #6 on: July 10, 2020, 11:35:05 PM »
Copper drains are uncommon in my California experience, except in expensive rain gutter systems.  The associated pipes and fittings (type DWV, even thinner than type M) are easy to get.
https://www.plumbingsupplynow.com/fittings/copper-dwv/

I remember when they stopped selling copper sulfate, for pouring down the drain to kill tree roots in clay drain pipes underground.  Now industrial printed circuit fabricators need to reclaim the copper from used etchant.  On a hobby scale, I think copper from DIY circuit boards is minor, like silver from DIY photo developing once upon a time, and tin-lead solder waste into the garbage can. 

The only etchants I've used for circuit boards are ferric chloride (temperature and agitation are important) and plain salt water with electric current (can even etch stainless steel).
« Last Edit: July 11, 2020, 04:16:51 AM by klugesmith »

Offline Twospoons

  • High Voltage Engineer
  • ****
  • Posts: 221
  • Karma: +6/-0
    • View Profile
Re: PCB etching, DIY (chemistry mostly)
« Reply #7 on: July 11, 2020, 01:35:07 AM »
Last time I used HCl/peroxide it went pretty fast. It does rely on good air contact though.
I've always felt the best results were from warm, fresh, agitated FeCl3. Brushing or spraying work very well.  Obvious downside is the mess - FeCl3 stains everything.
Persulfate is much cleaner, but I felt I got more pinholing with it. Its also slower, and MUST be used hot.

Spent etchant should really be processed to remove the copper - simple enough to electroplate it out.

Offline klugesmith

  • High Voltage Senior
  • *****
  • Posts: 688
  • Karma: +22/-0
    • View Profile
Re: PCB etching, DIY (chemistry mostly)
« Reply #8 on: July 11, 2020, 04:18:29 AM »
Sort of off topic, but since we are talking about toxic metals in the drain...

California mines produced roughly 100,000 tons of mercury, starting in 1840's, of which 10% or more ended up in local and Gold Rush river beds.  From which it slowly leaches even today.
https://www.kqed.org/quest/17506/mercury-in-san-francisco-bay
« Last Edit: July 11, 2020, 07:03:52 AM by klugesmith »

High Voltage Forum

Re: PCB etching, DIY (chemistry mostly)
« Reply #8 on: July 11, 2020, 04:18:29 AM »

 


* Recent Topics and Posts

post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
Today at 01:01:12 PM
post Re: Big Coil Build Log
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
Today at 05:47:34 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
davekni
Today at 04:45:07 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
Today at 04:18:27 AM
post Push Pull VTTC
[Vacuum Tube Tesla Coils (VTTC)]
janno288
Today at 01:10:08 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 27, 2024, 10:54:52 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 27, 2024, 11:53:42 AM
post Re: OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 05:14:36 AM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:47:48 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 27, 2024, 04:41:59 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 27, 2024, 12:04:34 AM
post Re: Super flat QCW simulation (does this look reasonable?)
[Dual Resonant Solid State Tesla coils (DRSSTC)]
toooldforthis
March 26, 2024, 11:08:14 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 11:07:20 PM
post Re: Is the UD2.7C under voltage lock out basically worthless?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 10:46:29 PM
post OCD Triggering Early + Low Output
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 26, 2024, 09:03:43 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 08:46:59 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 26, 2024, 05:02:18 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 26, 2024, 03:16:03 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 26, 2024, 01:41:49 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 26, 2024, 04:48:22 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 26, 2024, 04:16:37 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 26, 2024, 04:16:24 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 26, 2024, 04:13:02 AM
post Re: CM400 Induction Heater
[Electronic Circuits]
davekni
March 26, 2024, 04:00:43 AM
post Re: Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
davekni
March 26, 2024, 03:19:18 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
March 26, 2024, 01:50:42 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 08:05:02 PM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 25, 2024, 07:41:29 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 06:45:46 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 25, 2024, 05:44:25 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
Anders Mikkelsen
March 25, 2024, 04:47:17 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
March 25, 2024, 04:27:22 PM
post Re-chargeable 1.5 volt lithium ion AAA batteries
[General Chat]
MRMILSTAR
March 25, 2024, 03:57:34 PM
post Re: CM400 Induction Heater
[Electronic Circuits]
markus
March 25, 2024, 02:06:41 PM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 04:43:25 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
davekni
March 25, 2024, 02:39:40 AM
post Re: Odd MOSFET Driver Behavior
[Solid State Tesla Coils (SSTC)]
KrisPringle
March 25, 2024, 12:47:09 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 24, 2024, 07:36:32 PM
post Re: My completed 14-stage Cockroft-Walton voltage multiplier
[Voltage Multipliers]
Alberto
March 24, 2024, 07:27:24 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 24, 2024, 04:25:23 AM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 10:47:35 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 09:30:21 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 04:34:31 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 03:04:25 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 23, 2024, 01:38:34 PM
post Re: capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
MRMILSTAR
March 23, 2024, 04:20:03 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 23, 2024, 12:54:30 AM
post Re: Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
davekni
March 23, 2024, 12:05:57 AM
post capacitor and diodes. Voltage values for a CW
[Voltage Multipliers]
Alberto
March 22, 2024, 11:45:03 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 22, 2024, 11:30:09 PM
post Smoke Screen Machine Protect 950 XP - Teardown of a Smoke Cannon!
[Electronic Circuits]
Mads Barnkob
March 22, 2024, 10:20:35 PM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Benbmw
March 22, 2024, 09:21:13 PM
post Re: What actually kills MOSFETs?
[Beginners]
AstRii
March 22, 2024, 03:37:11 PM
post What actually kills MOSFETs?
[Beginners]
FPS
March 22, 2024, 05:09:20 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 22, 2024, 03:57:54 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 22, 2024, 02:59:25 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 06:31:42 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
rikkitikkitavi
March 21, 2024, 03:08:01 PM
post Re: [WTS] IGBT, Ferrite, Capacitors, Tools, PSU, Industrial components and parts
[Sell / Buy / Trade]
Mads Barnkob
March 21, 2024, 01:37:32 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Alberto
March 21, 2024, 11:42:07 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 21, 2024, 04:09:14 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 21, 2024, 02:15:31 AM
post My Homemade Structural Analysis X-Ray Machine
[X-ray]
Luca c.
March 21, 2024, 01:35:40 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 20, 2024, 10:40:00 PM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Mads Barnkob
March 20, 2024, 08:03:41 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Mads Barnkob
March 20, 2024, 07:51:57 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 20, 2024, 10:39:47 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
March 20, 2024, 04:09:59 AM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 20, 2024, 01:13:23 AM
post Re: Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
March 20, 2024, 12:45:16 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 20, 2024, 12:30:30 AM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 11:12:24 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:47:49 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 19, 2024, 09:44:19 PM
post Phase Lead Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
March 19, 2024, 06:52:09 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 19, 2024, 05:02:44 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
Mads Barnkob
March 19, 2024, 05:01:41 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 04:31:02 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
March 19, 2024, 03:59:54 PM
post Re: Benjamin's DRSSTC 2 in progress
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
March 19, 2024, 06:41:39 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
davekni
March 19, 2024, 04:05:49 AM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
OmGigaTron
March 18, 2024, 09:08:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 09:07:35 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
Twospoons
March 18, 2024, 08:57:06 PM
post Re: Can I Trust This Super Cheap Site?
[General Chat]
MRMILSTAR
March 18, 2024, 03:51:33 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:59:46 PM
post Re: 160mm DRSSTC II project | Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Late
March 18, 2024, 02:33:25 PM
post Can I Trust This Super Cheap Site?
[General Chat]
2020-Man
March 18, 2024, 11:02:12 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Twospoons
March 18, 2024, 02:36:11 AM
post Re: Best forum for vacuum tube amplifiers?
[General Chat]
Mads Barnkob
March 17, 2024, 07:42:55 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:15:14 PM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 05:05:04 AM
post Re: Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
davekni
March 17, 2024, 04:50:51 AM
post Re: 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Twospoons
March 17, 2024, 04:45:17 AM
post 2x Panasonic Inverter Microwaves - what to salvage, dangers?
[General Chat]
Michelle_
March 17, 2024, 04:17:51 AM
post Where's all this voltage coming from?
[Spark Gap Tesla Coils (SGTC)]
Terry
March 17, 2024, 01:29:32 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
March 17, 2024, 12:33:06 AM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Keybored
March 16, 2024, 08:46:20 PM
post Re: Bleeder resistor for MMC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hydron
March 16, 2024, 08:39:24 PM
post Re: DRSSTC Questions
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Hydron
March 16, 2024, 08:21:44 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal