Author Topic: Now building a spark chamber  (Read 2660 times)

Offline pentode

  • High Voltage Enthusiast
  • *
  • Posts: 36
  • Karma: +2/-0
    • View Profile
    • humourous
Now building a spark chamber
« on: April 24, 2019, 05:41:07 PM »
I don't suppose anyone is interested in dated spark chambers but...….
I have started building a circular one using Argon gas.
Circular is much easier to seal to ensure it's gas tight.

10 Aluminium plates 200mm dia spaced at 20mm giving a 180mm high display.
Adjustable 25kV DC across alternate plates, non pulsed.

Non pulsed HV was used in the very early spark chambers but one gets spurious discharges.

If my non pulsed system doesn't work I shall have to spend, spend, spend on scintillators and
photo multiplier tubes, amps and timing extras.
"One small step for man"...
…..because he has Arthritis.
www.retinascope.co.uk

Offline pentode

  • High Voltage Enthusiast
  • *
  • Posts: 36
  • Karma: +2/-0
    • View Profile
    • humourous
Re: Now building a spark chamber
« Reply #1 on: April 27, 2019, 12:56:40 PM »

Here's the 10 aluminium  discs with 20mm nylon spacers and nylon bolts.
Each alternate one to be connected for HV supply.
This is just a mock up to ensure everything fits together.   :)

Plates must be even to each other within about 1% so that's .2mm in this case.

Acrylic enclosure shown to have top and bottom plates attached, gas proof
with valves to supply argon and drain chamber of air.

"One small step for man"...
…..because he has Arthritis.
www.retinascope.co.uk

Offline Mads Barnkob

  • Administrator
  • High Voltage Expert
  • *****
  • Posts: 1738
  • Karma: +42/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: Now building a spark chamber
« Reply #2 on: April 27, 2019, 08:55:23 PM »
You have me following your build process :)

Nothing wrong with dated and old school scientific equipment as they are often the basic principles that more modern and complex equipment is build upon, looking forward to see your results.
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline pentode

  • High Voltage Enthusiast
  • *
  • Posts: 36
  • Karma: +2/-0
    • View Profile
    • humourous
Re: Now building a spark chamber
« Reply #3 on: April 30, 2019, 02:19:21 PM »
I hunted around for some small valves for gas inlet/air outlet.
As the whole rig is only 200mm dia x 250mm high I didn't
wish for large ones, so I bought two model railway engine valves. (60mm high)

Both mounted on the top acrylic plate where the argon gas is not inclined to escape
anyway as it is heavier than air.

The rig will be tilted to one side to fill the chamber, argon pushing the air up
and out.....I hope. :)  If a problem I shall have to  pipe the gas to the bottom of the chamber.

Now how to know when the chamber is full?
I shall use a lighted match burning at the exit valve and when it goes out
I should be nearly there !

Is there a better way?




« Last Edit: April 30, 2019, 02:21:18 PM by pentode »
"One small step for man"...
…..because he has Arthritis.
www.retinascope.co.uk

Offline pentode

  • High Voltage Enthusiast
  • *
  • Posts: 36
  • Karma: +2/-0
    • View Profile
    • humourous
Re: Now building a spark chamber
« Reply #4 on: May 01, 2019, 09:42:26 PM »
Whilst waiting for more parts I built the power supply on the acrylic base mounted under the base. (It will be covered for safety as the voltage will be up to 25kV.  )
Initially the supply will be from a 15kV 30m/a  NST I stripped from an old SGTC I once built.

Nothing unusual in the power supply, just series HV diodes in a bridge with smoothing caps and bleeders wound around a piece of acrylic tube.
I always use nylon bolts, super glued to bases etc  to make cheap stand off HV insulators.

 

"One small step for man"...
…..because he has Arthritis.
www.retinascope.co.uk

Offline pentode

  • High Voltage Enthusiast
  • *
  • Posts: 36
  • Karma: +2/-0
    • View Profile
    • humourous
Re: Now building a spark chamber
« Reply #5 on: May 03, 2019, 09:11:42 AM »
I thought about pressure build up in the chamber as sparking will warm up the Argon gas
and so pressure build up.

To keep an eye on this in a very cheap way I will fit a thin sheet of neoprene
onto a 60mm dia neoprene flat washer.  This will be fitted to the top
acrylic plate with a small hole drilled through it.

In this way any pressure increase or decrease will immediately show as a
depression or bulge in the neoprene. (dotted lines)
It will be interesting to watch this as sparking occurs.
I may put a position sensor on it too.

So I can keep an eye on pressure and cut the HV if too much.





« Last Edit: May 03, 2019, 09:17:56 AM by pentode »
"One small step for man"...
…..because he has Arthritis.
www.retinascope.co.uk

Offline pentode

  • High Voltage Enthusiast
  • *
  • Posts: 36
  • Karma: +2/-0
    • View Profile
    • humourous
Re: Now building a spark chamber
« Reply #6 on: May 05, 2019, 11:13:20 AM »
When a partical passing through my chamber ionises the Argon, ( I hope  ),
the spark created will continue so I need to cut the HV after some
short time. As I am finding, switching 20kV plus HV is rather costly so I will make a short period timer to cut the mains supply to the NST, if I can
detect when a spark has been triggered by a partical and not spurious.


This is all a new ball game for me and the next part of the game is ordering
a small cylinder of Argon and a regulator.
to suit. I think these will fit the bill from Machine Mart who is near to me...……..
  https://www.machinemart.co.uk/p/argon-gas-cylinder

https://www.machinemart.co.uk/p/bottle-regulator-small-gas-bottle/?da=1&TC=GS-010120110&gclid=CjwKCAjwk7rmBRAaEiwAhDGhxAv38k0Mveuq4iDGj-d5h0VlQeo9blAsNy8uW2lPxb7esL1KbnfboRoC6RQQAvD_BwE


Maybe I ought to train up as a gas engineer. ;D
« Last Edit: May 05, 2019, 11:24:17 AM by pentode »
"One small step for man"...
…..because he has Arthritis.
www.retinascope.co.uk

High Voltage Forum

Re: Now building a spark chamber
« Reply #6 on: May 05, 2019, 11:13:20 AM »

 


* Recent Topics and Posts

post Re: First middle sized DRSSTC - Phase lead tuning
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Rapy2
Today at 01:06:02 AM
post Re: First middle sized DRSSTC - Phase lead tuning
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
Today at 12:44:31 AM
post Re: First middle sized DRSSTC - Phase lead tuning
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Rapy2
Today at 12:41:33 AM
post Re: First middle sized DRSSTC - Phase lead tuning
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Rapy2
Today at 12:11:13 AM
post Re: First middle sized DRSSTC - Phase lead tuning
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
June 13, 2021, 11:52:11 PM
post Re: First middle sized DRSSTC - Phase lead tuning
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Rapy2
June 13, 2021, 11:38:44 PM
post Re: First middle sized DRSSTC - Phase lead tuning
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Rapy2
June 13, 2021, 10:26:51 PM
post Re: First middle sized DRSSTC - Phase lead tuning
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
June 13, 2021, 09:57:56 PM
post Re: First middle sized DRSSTC - Phase lead tuning
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Rapy2
June 13, 2021, 09:29:08 PM
post Re: First middle sized DRSSTC - Phase lead tuning
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
June 13, 2021, 08:53:25 PM
post Re: First middle sized DRSSTC - Phase lead tuning
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Rapy2
June 13, 2021, 07:22:05 PM
post Re: First middle sized DRSSTC - Phase lead tuning
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
June 13, 2021, 07:02:28 PM
post Re: HFSSTC with fixed crystal-controlled frequency
[Solid State Tesla Coils (SSTC)]
Steve Ward
June 13, 2021, 06:25:20 PM
post First middle sized DRSSTC - Phase lead tuning
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Rapy2
June 13, 2021, 02:48:59 PM
post OpenTheremin v3 loosing calibration after minutes
[Electronic Circuits]
gianpaolo
June 13, 2021, 12:00:09 PM
post Re: What is the guidence on SpaceX rockets based on ? PID's?
[General Chat]
Mads Barnkob
June 12, 2021, 07:28:03 PM
post Re: Rocket engine questions
[General Chat]
klugesmith
June 12, 2021, 07:23:12 PM
post Re: Rocket engine questions
[General Chat]
rikkitikkitavi
June 12, 2021, 12:24:06 PM
post Re: Nice PC Board Tesla
[Solid State Tesla Coils (SSTC)]
Da_Stier
June 12, 2021, 10:06:18 AM
post Re: Rocket engine questions
[General Chat]
plasma
June 12, 2021, 10:01:29 AM
post Re: Nice PC Board Tesla
[Solid State Tesla Coils (SSTC)]
Twospoons
June 12, 2021, 08:47:08 AM
post Re: What is the guidence on SpaceX rockets based on ? PID's?
[General Chat]
Patrick
June 12, 2021, 07:03:10 AM
post Re: Complications in the design of the first DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
PEDRO HENRIQUE
June 12, 2021, 06:42:56 AM
post Re: Nice PC Board Tesla
[Solid State Tesla Coils (SSTC)]
davekni
June 12, 2021, 04:20:53 AM
post Re: SKM100 Mini DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Willsmith001
June 11, 2021, 11:08:24 PM
post Re: How much propagation delay is too much propagation delay
[General Chat]
Willsmith001
June 11, 2021, 11:07:00 PM
post Re: Nice PC Board Tesla
[Solid State Tesla Coils (SSTC)]
Da_Stier
June 11, 2021, 12:33:55 PM
post Re: Nice PC Board Tesla
[Solid State Tesla Coils (SSTC)]
futurist
June 11, 2021, 12:03:24 PM
post Re: How much propagation delay is too much propagation delay
[General Chat]
davekni
June 11, 2021, 06:47:52 AM
post Re: How much propagation delay is too much propagation delay
[General Chat]
Power-Max
June 11, 2021, 06:32:02 AM
post Re: How much propagation delay is too much propagation delay
[General Chat]
davekni
June 11, 2021, 05:16:03 AM
post Re: SKM100 Mini DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
June 11, 2021, 04:53:50 AM
post Re: Why are SGT50T65FD1PN soo cheap on lcsc?
[General Chat]
Hydron
June 10, 2021, 11:51:17 PM
post Re: Rocket engine questions
[General Chat]
MRMILSTAR
June 10, 2021, 09:52:59 PM
post Re: Rocket engine questions
[General Chat]
Patrick
June 10, 2021, 09:16:25 PM
post Re: Why are SGT50T65FD1PN soo cheap on lcsc?
[General Chat]
Weston
June 10, 2021, 08:19:40 PM
post Fujifilm PMT module PMT12A, reverse engineering
[Detection, Counting and Measurements]
Mads Barnkob
June 10, 2021, 08:05:27 PM
post Nice PC Board Tesla
[Solid State Tesla Coils (SSTC)]
alan sailer
June 10, 2021, 07:46:12 PM
post Re: Is it possible to go fully CW with a DRSSRC?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Uspring
June 10, 2021, 06:31:40 PM
post Re: Why are SGT50T65FD1PN soo cheap on lcsc?
[General Chat]
rikkitikkitavi
June 10, 2021, 02:12:07 PM
post Re: Help for people buying the "12-48 Volt 1800/2500 Watt ZVS induction Heater"
[Electronic Circuits]
T3sl4co1l
June 10, 2021, 05:14:41 AM
post How much propagation delay is too much propagation delay
[General Chat]
Power-Max
June 10, 2021, 05:10:24 AM
post Re: Why are SGT50T65FD1PN soo cheap on lcsc?
[General Chat]
Power-Max
June 10, 2021, 04:50:34 AM
post Re: SKM100 Mini DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
June 10, 2021, 01:36:31 AM
post Re: Why are SGT50T65FD1PN soo cheap on lcsc?
[General Chat]
Steve Ward
June 09, 2021, 09:15:22 PM
post Re: Is it possible to go fully CW with a DRSSRC?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Power-Max
June 09, 2021, 08:02:15 PM
post Re: Complications in the design of the first DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
PEDRO HENRIQUE
June 09, 2021, 07:17:27 PM
post Re: Analog HFBR amplifier
[Electronic Circuits]
Max
June 09, 2021, 06:58:33 PM
post Aisler PCB Manufacturer
[Printed Circuit Board]
Max
June 09, 2021, 06:58:12 PM
post [WTS] (US) Large Ferrite U and E Cores, assorted types
[Sell / Buy / Trade]
Steve Ward
June 09, 2021, 05:44:06 PM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal