Author Topic: Reverse engineering a big old American smoke detector  (Read 2110 times)

Offline klugesmith

  • High Voltage Engineer
  • ****
  • Posts: 378
  • Karma: +12/-0
    • View Profile
Reverse engineering a big old American smoke detector
« on: March 15, 2020, 09:50:48 PM »
Just noticed the thread about big old Soviet smoke detector, which makes this one seem as safe as baby ducklings.  Told this story yesterday, in almost the same words, on another forum.

Here is an old stock Pyrotronics F5B smoke detector head, similar to the F3/5 head. They are still available for people maintaining old installations, but typically cost well over $100 on ebay.

Ionization-type smoke detectors seem to have started in the 1960's. Preventing fires in industrial & institutional settings easily justified the proliferation of 80 microcurie Am-241 alpha particle sources. Those produce enough air ionization that a cold cathode trigger tube can switch the alarm circuit.

I got the pictured device to turn on a neon lamp, within a few seconds of being exposed to smoke from a smoldering popsicle stick. My circuit is shown below, on the right. The original application uses Base Units (sockets) with resistors and a neon indicator lamp, and if any reader has one I'd love to know the circuit details.

.
These old smoke detectors, just like modern ones with less than 1 uCi of radioisotope, use a reference ionization chamber as the high impedance on top of voltage divider. Cheaper than a many-gigaohm resistor, and it automatically compensates for pressure and temperature and decay of the alpha particle source.

I found out that the internal construction is similar to this unfinished drawing.  The ion chambers in schematic above were rendered accordingly.


It came as a surprise that the larger ionization source, which irradiates the smoky chamber, is directly visible through the window-screened ports. Close enough that energetic alpha particles, not just ions, could be escaping from the enclosure. Let's check with some alpha-viewing fluorescent film, like what's sold for making spinthariscopes.


Set shutter time to 30 s, aperture f/1.4, ISO 12800. Lights off, not completely. Go...


This device could be disassembled without any screwdriving, wrenching, or cutting. 
Not sure if that's a good idea, or a thing to talk about.
Even if it were reassembled and tested as a working smoke detector, good as new, ready to protect lives.

Offline John123

  • High Voltage Engineer
  • ****
  • Posts: 227
  • Karma: +4/-0
  • All the gear, no idea. UK
    • View Profile
Re: Reverse engineering a big old American smoke detector
« Reply #1 on: March 16, 2020, 05:57:16 AM »
Looks quite big in the photo compared to the ones inside modern detectors.

How come they were designed as replaceable parts, do they wear out and become unreliable over time?

Offline johnf

  • High Voltage Technician
  • ***
  • Posts: 163
  • Karma: +5/-0
    • View Profile
Re: Reverse engineering a big old American smoke detector
« Reply #2 on: March 18, 2020, 07:34:09 PM »
I think the part has been made much like tubes were made
in fact that looks like a standard octal tube base with a few pins missing.
this would fit well with early electronics manufacture allowing all to be tested before the detector head was put in

Offline TheMaxii2007

  • High Voltage Enthusiast
  • *
  • Posts: 3
  • Karma: +0/-0
    • View Profile
Re: Reverse engineering a big old American smoke detector
« Reply #3 on: June 02, 2020, 04:19:02 AM »
Hello My old smoke detector Am-241 (72 microcurie )  ;)






« Last Edit: June 02, 2020, 04:32:01 AM by TheMaxii2007 »

Offline klugesmith

  • High Voltage Engineer
  • ****
  • Posts: 378
  • Karma: +12/-0
    • View Profile
Re: Reverse engineering a big old American smoke detector
« Reply #4 on: June 04, 2020, 06:30:09 AM »
Welcome to the forum, and thank you for the interesting report.

The sectional drawing you shared is much better than anything I've seen before.
It sure beats measuring parts and drawing things from scratch.
Does the document it came from include details of the circuit in base unit?

Is there a model number and/or date code on your device? 
How come the nominal activity is 72 uCi, vs 80 uCi in my specimens and in the F3/5 model we can read about?

Might as well share a picture I made with alpha-viewing film, to get an idea of relative activity in the outer and inner chamber irradiators, next to a modern sub-1-uCi source.
« Last Edit: June 04, 2020, 06:49:45 AM by klugesmith »

Offline TheMaxii2007

  • High Voltage Enthusiast
  • *
  • Posts: 3
  • Karma: +0/-0
    • View Profile

High Voltage Forum

Re: Reverse engineering a big old American smoke detector
« Reply #5 on: June 06, 2020, 10:44:15 PM »

 


* Recent Topics and Posts

post Re: Proper phase lead adjustment at the input
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
Today at 10:15:30 PM
post CW Help -- too much info to digest
[Voltage Multipliers]
abstruse1
Today at 06:16:53 PM
post Re: Proper phase lead adjustment at the input
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Chrisader
Today at 04:16:11 PM
post Re: Gate driver for big IGBTs
[Electronic Circuits]
davekni
Today at 05:38:42 AM
post Gate driver for big IGBTs
[Electronic Circuits]
TMaxElectronics
Today at 02:15:25 AM
post Re: Modified VTTC for induction heating
[Vacuum Tube Tesla Coils (VTTC)]
dbach
July 24, 2021, 11:38:33 PM
post Re: Modified VTTC for induction heating
[Vacuum Tube Tesla Coils (VTTC)]
Mads Barnkob
July 24, 2021, 11:29:15 PM
post Re: repair of Panasonic microwave inverter
[Electronic Circuits]
Twospoons
July 24, 2021, 10:41:38 PM
post Modified VTTC for induction heating
[Vacuum Tube Tesla Coils (VTTC)]
dbach
July 24, 2021, 09:18:42 PM
post Re: repair of Panasonic microwave inverter
[Electronic Circuits]
Mads Barnkob
July 24, 2021, 08:08:36 PM
post Re: Tesla Coil Show Controller Project
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Max
July 24, 2021, 11:13:18 AM
post Re: repair of Panasonic microwave inverter
[Electronic Circuits]
Weston
July 24, 2021, 10:08:34 AM
post Re: Horrible waveforms advice--just bad test setup?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 24, 2021, 03:20:42 AM
post Re: repair of Panasonic microwave inverter
[Electronic Circuits]
Twospoons
July 24, 2021, 03:16:27 AM
post 3kW Cisco Server Supply teardown and help needed
[Electronic Circuits]
Da_Stier
July 23, 2021, 09:23:11 PM
post Re: IGBT question
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
July 23, 2021, 08:05:58 PM
post Re: IGBT question
[Dual Resonant Solid State Tesla coils (DRSSTC)]
futurist
July 23, 2021, 07:02:18 PM
post Re: IGBT question
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
July 23, 2021, 05:33:57 PM
post Re: Horrible waveforms advice--just bad test setup?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
GKnapp
July 23, 2021, 04:51:37 PM
post Re: Horrible waveforms advice--just bad test setup?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 23, 2021, 03:52:46 AM
post Re: IGBT question
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
July 22, 2021, 10:59:32 PM
post Re: Horrible waveforms advice--just bad test setup?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
GKnapp
July 22, 2021, 08:50:34 PM
post Re: IGBT question
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
July 22, 2021, 08:47:23 PM
post Help needed - which IGBT module to buy
[Dual Resonant Solid State Tesla coils (DRSSTC)]
thedoc298
July 22, 2021, 07:01:24 PM
post Re: Horrible waveforms advice--just bad test setup?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 22, 2021, 06:50:07 AM
post Re: Proper phase lead adjustment at the input
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 22, 2021, 06:39:37 AM
post Re: Horrible waveforms advice--just bad test setup?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
alan sailer
July 21, 2021, 07:55:03 PM
post Horrible waveforms advice--just bad test setup?
[Dual Resonant Solid State Tesla coils (DRSSTC)]
GKnapp
July 21, 2021, 06:34:13 PM
post Re: Global shutter synchronized to arcs?
[DSLR]
Uspring
July 21, 2021, 05:10:18 PM
post Re: Tesla Coil Show Controller Project
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
July 21, 2021, 12:42:29 PM
post Re: Proper phase lead adjustment at the input
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Chrisader
July 21, 2021, 08:15:00 AM
post Re: Proper phase lead adjustment at the input
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
July 21, 2021, 04:57:04 AM
post Re: Micro-power continuity checker.
[Electronic Circuits]
davekni
July 21, 2021, 03:50:33 AM
post Re: Skm flyback destroyer 🤗
[Transformer (Ferrite Core)]
oneKone
July 21, 2021, 01:50:19 AM
post Proper phase lead adjustment at the input
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Chrisader
July 20, 2021, 10:06:14 PM
post Re: Micro-power continuity checker.
[Electronic Circuits]
klugesmith
July 20, 2021, 06:24:29 PM
post Micro-power continuity checker.
[Electronic Circuits]
davekni
July 20, 2021, 05:37:36 AM
post Re: Help needed with SSTC. First TC build
[Solid State Tesla Coils (SSTC)]
davekni
July 20, 2021, 05:08:24 AM
post Re: Global shutter synchronized to arcs?
[DSLR]
davekni
July 20, 2021, 04:43:05 AM
post Re: Global shutter synchronized to arcs?
[DSLR]
TMaxElectronics
July 20, 2021, 12:09:36 AM
post Re: Help needed with SSTC. First TC build
[Solid State Tesla Coils (SSTC)]
AstRii
July 19, 2021, 11:13:13 PM
post Another question on CT Feedback
[Solid State Tesla Coils (SSTC)]
Maverikie
July 19, 2021, 08:56:04 PM
post Re: Sync RSG motor problems - help and thoughts needed
[Spark Gap Tesla Coils (SGTC)]
newage
July 19, 2021, 07:09:56 PM
post Re: Global shutter synchronized to arcs?
[DSLR]
klugesmith
July 19, 2021, 06:49:08 PM
post Re: Sync RSG motor problems - help and thoughts needed
[Spark Gap Tesla Coils (SGTC)]
klugesmith
July 19, 2021, 04:39:05 PM
post Global shutter synchronized to arcs?
[DSLR]
davekni
July 19, 2021, 06:32:35 AM
post Re: Sync RSG motor problems - help and thoughts needed
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
July 19, 2021, 05:22:51 AM
post Re: Sync RSG motor problems - help and thoughts needed
[Spark Gap Tesla Coils (SGTC)]
newage
July 19, 2021, 04:24:38 AM
post Re: a typical sstc half bridge design, any considerations or tips?
[Solid State Tesla Coils (SSTC)]
eli
July 19, 2021, 12:35:18 AM
post Re: a typical sstc half bridge design, any considerations or tips?
[Solid State Tesla Coils (SSTC)]
Mads Barnkob
July 19, 2021, 12:15:43 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal