Author Topic: 30% power increase  (Read 1922 times)

Offline MRMILSTAR

  • High Voltage Senior
  • *****
  • Posts: 557
  • Karma: +20/-0
  • Cedar Rapids, Iowa
    • View Profile
30% power increase
« on: August 06, 2019, 04:35:37 PM »
I recently increased the power of my big SGTC by about 30%, from 4.8 KVA to 6.5 KVA. This was very simple to do on my equipment. All I had to do was increase the air gap on my ballast very slightly. JAVATC predicted a 9-foot maximum streamer length. A neighbor took the attached picture. If I stretch out all of the kinks, the streamer length does indeed measure to about 9 feet. For reference the coil is 75" tall.

This is the maximum power that I can safely use with my current components. My weak link is my variac which is the largest General Radio variac available. It is rated for 240 volts at 25 amps continuous and up to 32 amps with cooling intervals. My current power level draws 27 amps, with PFC, through the variac. This is the maximum that I am comfortable with unless I want to make major modifications (2 ganged variacs and more capacitance).
Steve White
Cedar Rapids, Iowa
Retired electrical engineer

Offline Mads Barnkob

  • Administrator
  • Executive Board Member
  • *****
  • Posts: 2281
  • Karma: +73/-0
  • Denmark
    • View Profile
    • Kaizer Power Electronics
Re: 30% power increase
« Reply #1 on: August 08, 2019, 08:33:01 AM »
I was never so bold to "stretch" out the spark for spark length measurements  :P

Most variacs are rated for 200-300% operation for very short periods, it will however hum violently, just if you wanted to push things a bit :)
https://kaizerpowerelectronics.dk - Tesla coils, high voltage, pulse power, audio and general electronics
https://www.youtube.com/KaizerPowerElectronicsDk60/join - Please consider supporting the forum, websites and youtube channel!

Offline MRMILSTAR

  • High Voltage Senior
  • *****
  • Posts: 557
  • Karma: +20/-0
  • Cedar Rapids, Iowa
    • View Profile
Re: 30% power increase
« Reply #2 on: August 08, 2019, 04:18:09 PM »
The GR variacs also have an internal fuse which I believe is rated for 32 amps, so that is another limitation. I could just bypass the fuse since my control cabinet has a 40 amp breaker. However, going higher than 27 amps would be largely pointless without increasing the size of my primary circuit capacitance. With my 45 nF capacitance, JAVATC says that my capacitors are 95% charged at the start of each bang (240 BPS) with 27 amps. I could increase the capacitance to 60 nF since I do have additional Maxwell energy discharge capacitors. I might do that some day but for now, 9-foot streamers satisfy me.

My ultimate limit though are the 40 amp breakers in my distribution panel.
« Last Edit: August 08, 2019, 04:22:59 PM by MRMILSTAR »
Steve White
Cedar Rapids, Iowa
Retired electrical engineer

High Voltage Forum

Re: 30% power increase
« Reply #2 on: August 08, 2019, 04:18:09 PM »

 


* Recent Topics and Posts

post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
Today at 06:30:43 PM
post Re: Tesla coil UV eye protection?
[General Chat]
Michelle_
Today at 06:14:35 PM
post Re: Tesla coil UV eye protection?
[General Chat]
MRMILSTAR
Today at 05:13:46 PM
post Re: Tesla coil UV eye protection?
[General Chat]
Twospoons
Today at 11:40:08 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
NyaaX_X
Today at 06:01:50 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
Today at 05:55:45 AM
post Re: Tesla coil UV eye protection?
[General Chat]
Michelle_
Today at 05:47:36 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
Today at 05:45:36 AM
post Re: Tesla coil UV eye protection?
[General Chat]
MRMILSTAR
Today at 05:41:05 AM
post Re: Tesla coil UV eye protection?
[General Chat]
Twospoons
Today at 04:33:57 AM
post Re: Tesla coil UV eye protection?
[General Chat]
alan sailer
April 24, 2024, 08:02:47 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 24, 2024, 06:51:17 PM
post Re: Tesla coil UV eye protection?
[General Chat]
Michelle_
April 24, 2024, 06:45:00 PM
post Re: Tesla coil UV eye protection?
[General Chat]
Mads Barnkob
April 24, 2024, 05:18:27 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
NyaaX_X
April 24, 2024, 05:14:27 PM
post Re: Ignitron trigger drive ideas?
[Capacitor Banks]
huntergroundmind
April 24, 2024, 02:51:23 PM
post Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
April 24, 2024, 05:58:27 AM
post Tesla coil UV eye protection?
[General Chat]
Michelle_
April 24, 2024, 05:17:22 AM
post Re: Tenebrescent Potassium Iodide
[Solid State Tesla Coils (SSTC)]
alan sailer
April 24, 2024, 12:39:59 AM
post Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
April 23, 2024, 11:07:41 PM
post Re: First DRSSTC SKM100
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Saattvik24
April 23, 2024, 10:57:39 PM
post Re: Plasma Torid - Class E Self Resonant Dual/Stereo - Plasma Torid Build
[Dual Resonant Solid State Tesla coils (DRSSTC)]
OmGigaTron
April 23, 2024, 09:33:49 PM
post Re: Tenebrescent Potassium Iodide
[Solid State Tesla Coils (SSTC)]
haversin
April 23, 2024, 06:00:42 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 23, 2024, 03:50:49 AM
post Re: Tenebrescent Potassium Iodide
[Solid State Tesla Coils (SSTC)]
alan sailer
April 23, 2024, 03:13:31 AM
post Re: Tenebrescent Potassium Iodide
[Solid State Tesla Coils (SSTC)]
haversin
April 23, 2024, 12:50:40 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 11:21:06 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 08:11:00 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 06:15:30 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
NyaaX_X
April 22, 2024, 05:52:50 PM
post Tenebrescent Potassium Iodide
[Solid State Tesla Coils (SSTC)]
alan sailer
April 22, 2024, 05:52:13 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 04:31:52 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
NyaaX_X
April 22, 2024, 04:05:34 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
markus
April 22, 2024, 01:02:30 PM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
April 22, 2024, 06:32:35 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 06:24:10 AM
post M2000NM1 toroid for gdt tesla coil
[General Chat]
thedark
April 22, 2024, 05:13:15 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 02:25:29 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
alan sailer
April 22, 2024, 02:09:18 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 22, 2024, 12:14:21 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 21, 2024, 09:47:15 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
April 21, 2024, 08:34:02 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 21, 2024, 06:09:57 PM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
April 21, 2024, 06:21:54 AM
post Re: Insulate the secondary of the Tesla coil with a PET plastic bottle
[General Chat]
Michelle_
April 21, 2024, 06:18:30 AM
post Re: Insulate the secondary of the Tesla coil with a PET plastic bottle
[General Chat]
davekni
April 21, 2024, 06:12:31 AM
post Re: Insulate the secondary of the Tesla coil with a PET plastic bottle
[General Chat]
MRMILSTAR
April 21, 2024, 05:19:55 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 21, 2024, 02:29:17 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
alan sailer
April 21, 2024, 01:28:59 AM
post Insulate the secondary of the Tesla coil with a PET plastic bottle
[General Chat]
thedark
April 21, 2024, 01:19:44 AM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
flyingperson23
April 21, 2024, 12:55:25 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 20, 2024, 11:25:32 PM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
April 20, 2024, 10:28:26 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
davekni
April 20, 2024, 10:23:28 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 20, 2024, 10:06:44 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
davekni
April 20, 2024, 09:21:55 PM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
April 20, 2024, 09:16:14 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
April 20, 2024, 08:58:40 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 20, 2024, 06:18:26 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 20, 2024, 06:15:26 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
April 20, 2024, 03:45:43 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Benjamin Lockhart
April 20, 2024, 06:33:37 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 20, 2024, 05:45:04 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Benjamin Lockhart
April 20, 2024, 05:34:16 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 20, 2024, 04:50:57 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Benjamin Lockhart
April 20, 2024, 04:03:55 AM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Benjamin Lockhart
April 20, 2024, 02:35:56 AM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 19, 2024, 09:37:52 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
klugesmith
April 19, 2024, 09:20:10 PM
post Re: Next Gen DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
April 19, 2024, 07:22:26 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 19, 2024, 04:46:36 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
alan sailer
April 19, 2024, 03:49:28 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 19, 2024, 01:53:57 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
MRMILSTAR
April 19, 2024, 05:24:19 AM
post Re: Difference between these transformers
[Transformer (Ferrite Core)]
Tesla Junior
April 19, 2024, 04:24:09 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 19, 2024, 04:20:35 AM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 19, 2024, 04:05:28 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
alan sailer
April 19, 2024, 04:03:54 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 19, 2024, 03:19:19 AM
post Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
davekni
April 19, 2024, 03:09:29 AM
post Re: IKY150N65EH7, is it good for DRSSTC
[Dual Resonant Solid State Tesla coils (DRSSTC)]
unrealcrafter2
April 19, 2024, 01:47:37 AM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 19, 2024, 12:19:21 AM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
klugesmith
April 18, 2024, 11:33:01 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 18, 2024, 11:15:15 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
davekni
April 18, 2024, 10:59:36 PM
post Re: What actually kills MOSFETs?
[Beginners]
unrealcrafter2
April 18, 2024, 10:03:48 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
klugesmith
April 18, 2024, 09:53:25 PM
post Re: Welcome new members, come say hello and tell a little about yourself :)
[General Chat]
unrealcrafter2
April 18, 2024, 09:50:09 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 18, 2024, 09:15:55 PM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
Mads Barnkob
April 18, 2024, 08:50:49 PM
post Re: 100kHz CM300 gate resistor choice
[Dual Resonant Solid State Tesla coils (DRSSTC)]
unrealcrafter2
April 18, 2024, 08:11:27 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
davekni
April 18, 2024, 07:28:05 PM
post Re: How to get a GE Yokogawa AB40 Sync Scope to rotate without a powerplant.
[Laboratories, Equipment and Tools]
Bobakman
April 18, 2024, 06:30:30 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 18, 2024, 06:03:57 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 18, 2024, 05:26:13 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
NyaaX_X
April 18, 2024, 04:03:38 PM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 18, 2024, 02:56:40 PM
post Re: DIY induction guns? (warning:long)
[Induction Launchers, Coil Guns and Rails guns]
Benbmw
April 18, 2024, 06:17:15 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
Michelle_
April 18, 2024, 05:46:07 AM
post Re: Small-ish 3D printed SGTC via cheap ZVS flyback build, humbly asking a couple ?s
[Spark Gap Tesla Coils (SGTC)]
MRMILSTAR
April 18, 2024, 05:18:31 AM

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
SimplePortal 2.3.6 © 2008-2014, SimplePortal